2026-08-09

接地线缆 - 高压电池（拆卸和更换）

校正代码 16100022 0.48 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：执行下述程序时，请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。

警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。

拆卸

  1. Raise and support vehicle.
    注
    Set air suspension to "Jack Mode".
  2. Raise vehicle fully and lower lift onto locks.
    注
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side.
  3. Remove clips securing front aero shield.
    注
    5x push clips.
  4. Remove bolts securing front aero shield and remove from vehicle.
    注
    9x bolts, 10mm, 6 Nm.
  5. Release clips securing wheel house liner to front skid plate.
    注
    4x clips.
  6. Remove bolts securing front skid plate to body sill.
    注
    2x bolts, 15mm, 30 Nm.
  7. Remove bolts securing front skid plate to body casting.
    注
    2x bolts, 15mm, 60 Nm.
  8. Remove bolts securing front skid plate to front subframe and remove skid plate.
    注
    4x bolts, 15mm, 70 Nm, 2x bolts, 10mm, 10 Nm.
  9. Release bolt securing ground strap to body.
    注
    1x bolt, 10mm, 9 Nm.
  10. Release clip securing ground cable to battery.
    注
    1x clip.
  11. Remove bolt securing ground cable to HV battery and remove assembly.
    注
    1x bolt, 10mm, 10 Nm? torque.

安装

  1. Route and install bolt securing ground cable to HV battery .
    注
    1x bolt, 10mm, 10 Nm? torque.
  2. Install clip securing ground cable to battery.
    注
    1x clip.
  3. Install bolt securing ground strap to body.
    注
    1x bolt, 10mm, 9 Nm.
  4. Position front skid plate for installation and thread in all bolts .
    注
    4x bolts, 15mm, 70 Nm, 2x bolts, 15mm, 60 Nm, 2x bolts, 15mm, 30 Nm, 2x bolts, 10mm, 10 Nm, Torque at later step.
  5. Torque bolts securing front skid plate to body casting.
    注
    2x bolts, 15mm, 60 Nm.
  6. Torque bolts securing front skid plate to body sill.
    注
    2x bolts, 15mm, 30 Nm.
  7. Torque bolts securing front skid plate to front subframe.
    注
    4x bolts, 15mm, 70 Nm, 2x bolts, 10mm, 10 Nm.
  8. Secure clips securing wheel house liner to front skid plate.
    注
    4x clips.
  9. Apply Loctite 222 onto front aero shield bolts and install fasteners securing front aero shield to vehicle.
    注
    9x bolts, 10mm, 6 Nm.
  10. Install clips securing front aero shield.
    注
    5x push clips.
  11. Lower vehicle fully.
    注
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered.
  12. Remove vehicle from lift.
    注
    Lower rack arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode".