2026-08-09

Harness - Active Noise Cancellation - Front - LH ((拆卸和更换))

校正代码 17107702 171077802 0.36 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

  • 2025-03-24: Released new procedure.
警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。

拆卸

  1. Open LH front door
  2. Raise and support vehicle
    注
    Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads
  3. Open hood
    注
    Select Controls > Frunk Open
  4. Remove rear underhood apron
    注
    8x clips
  5. Remove LH underhood apron
    注
    10x clips
  6. Remove RH underhood apron
    注
    10x clips
  7. Remove front underhood apron
    注
    7x clips
  8. Remove frunk access panel
    注
    3x clips, 3x hooks, 1x connector
  9. Remove frunk carpet
  10. Remove frunk assembly
    注
    4x bolts, 10mm, 5 Nm
  11. Disconnect active noise cancellation harness connector from frunk harness
    注
    1x connector, Release locking tab, 1x harness clip, Release clip securing active noise cancellation harness connector onto body
  12. Remove LH front wheel cap
    注
    Lift every other spoke at a time until cap is released from rim
  13. Loosen LH front wheel
    注
    5x nuts, 21mm, 175 Nm
  14. Raise vehicle partially and lower onto locks
    注
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  15. Remove LH front wheel
    注
    5x nuts, 21mm, 175 Nm
  16. Release clips securing active noise cancellation harness onto bracket
    注
    2x harness clip
  17. Disconnect active noise cancellation harness connector from sensor and remove harness from vehicle
    注
    1x connect, Release locking tab

安装

  1. Connect active noise cancellation harness onto sensor
    注
    1x connect, Secure locking tab
  2. Position active noise cancellation harness into place
    注
    Ensure the harness is routed above the lower links and below the tie rod and halfshaft
  3. Install clips securing active noise cancellation harness onto bracket
    注
    2x harness clip
  4. Install LH front wheel
    注
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  5. Lower vehicle until tires are touching ground
    注
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  6. Torque LH front wheel
    注
    5x nuts, 21mm, 175 Nm
  7. Install LH front wheel cap
    注
    Align valve stem with cap
  8. Connect active noise cancellation harness connector to frunk harness
    注
    1x connector, Secure locking tab, 1x harness clip, Install clip securing active noise cancellation harness connector onto body
  9. Install frunk assembly
    注
    4x bolts, 10mm, 5 Nm
  10. Install frunk carpet
    注
    Verify carpet is properly seated under the seal
  11. Install frunk access panel
    注
    3x clips, 3x hooks, 1x connector
  12. Install front underhood apron
    注
    7x clips
  13. Install RH underhood apron
    注
    10x clips
  14. Install LH underhood apron
    注
    10x clips
  15. Install rear underhood apron
    注
    8x clips
  16. Close hood
    注
    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
  17. Remove vehicle from lift
    注
    Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
  18. Close LH front door
    注
    Close doors