2025-11-22
饰板总成 - 前 (HW4)（拆卸和更换）
校正代码
10011032
0.72
注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。
注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至ServiceManualFeedback@tesla.com。
注意：请参阅 人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
注意：请参阅人体工程学注意事项查看安全健康的作业规程。
- 2025-11-17: Replaced radar heater disconnect step with reference to rework procedure. Removed steps to reinstall and reconnect radar heater.
- 2023-08-24: Added steps to transfer the front license plate brackets from the old fascia to the new fascia.
拆卸
- Remove the front license plate base bracket and front license plate molding painted bracket from the old front fascia so that they can be installed on the replacement fascia in a later step. See 底座支架 - 车牌 - 前（拆卸和更换）.
- Remove the front fascia assembly. See 饰板总成 - 前（拆下和安装）.
-
Disconnect the LH front fog light electrical connector. Repeat this step for the RH fog light electrical connector.
警告Do not push down on the red tab. Pull the red tab to disengage the lock, and then pull again to release the headlight electrical connector.
-
Remove the LV jumper wires (x2) from the tow hook cover.
注Squeeze the retaining tabs together and gently remove the jumper wires from the tow hook cover.
-
Disconnect the front Bluetooth Low Energy (BLE) module electrical connector.
警告Do not push down on the red tab. Pull the red tab to disengage the lock, and then pull again to release the BLE electrical connector.
- If the radar heater has not been permanently disconnected, perform the rework. See 加热器 - 雷达（返工）（2021 年 7 月 1 日之前生产的车辆） or 加热器 - 雷达（返工）（2021 年 7 月 1 日之后生产的车辆）.
-
Disconnect the pedestrian warning speaker electrical connector, and then release the electrical harness from the edge clip that is located on the RH side of the front fascia valance.
警告Do not push down on the red tab. Pull the red tab to disengage the lock, and then pull again to release electrical connector.
-
Release the clips (x10) that attach the electrical harness to the front fascia assembly, and then remove the electrical harness from the fascia.
-
Remove the screws (x3) that attach the RH front fog light to the front fascia assembly. Repeat this step for the LH front fog light.
1.8 Nm (1.3 lbs-ft)TIp推荐使用以下工具：- 梅花 T25 批头
-
Release the retaining tabs (x4) that attach the RH front fog light, and then remove the RH front fog light from the front fascia assembly. Repeat this step for the LH front fog light.
-
Remove the push clips (x8) that attach the valance to the front fascia assembly.
-
Remove the nuts (x2) that attach the valance to the front fascia assembly.3 Nm (2.2 lbs-ft)TIp推荐使用以下工具：
- 10 毫米套筒
注Release the LH and RH corners of the valance from the front fascia assembly. -
Remove the screws (x2) that attach the front fascia grille to the front fascia assembly.3 Nm (2.2 lbs-ft)TIp推荐使用以下工具：
- 梅花 T25 批头
-
Release the tabs (x11) that attach the front fascia grille to the front fascia assembly, and then remove the grille from the fascia.
-
Remove the screw that attaches the T badge support to the front fascia assembly.3 Nm (2.2 lbs-ft)TIp推荐使用以下工具：
- 梅花 T25 批头
-
Release the tabs (x4) that attach the T badge support to the front fascia assembly, and then remove the T badge support from the fascia.
安装
-
Put the new front fascia assembly on a padded workbench.
-
Fasten the tabs (x4) that attach the T badge support to the front fascia assembly.
-
Install the screw that attaches the T badge support to the front fascia assembly.3 Nm (2.2 lbs-ft)TIp推荐使用以下工具：
- 梅花 T25 批头
-
Fasten the tabs (x11) that attach the front fascia grille to the front fascia assembly.
-
Install the screws (x2) that attach the front fascia grille to the front fascia assembly.3 Nm (2.2 lbs-ft)TIp推荐使用以下工具：
- 梅花 T25 批头
-
Install the nuts (x2) that attach the valance to the front fascia assembly.3 Nm (2.2 lbs-ft)TIp推荐使用以下工具：
- 10 毫米套筒
注Interlock valance tabs with fascia tabs.注Secure the LH and RH corners of the valance to the front fascia assembly. -
Fasten the push clips (x8) that attach the valance to the front fascia assembly.
注Hold the front fascia tabs flush with valance, if necessary.
-
Fasten the retaining tabs (x4), and then install the screws (x3) that attach the LH front fog light. Repeat this step for the RH front fog light.1.8 Nm (1.3 lbs-ft)TIp推荐使用以下工具：
- 梅花 T25 批头
-
Fasten the clips (x10) that attach the electrical harness to the front fascia assembly.
-
Connect the pedestrian warning speaker electrical connector, and then secure it with the edge clip.
注Engage the locking tab.注The edge clip is located on the RH ride of the front fascia valance.
-
Connect the front BLE module electrical connector.
注Engage the locking tab.
-
Install the LV jumper wires (x2) to the tow hook cover.
注Make sure that both wire terminals are fully seated behind the retaining tabs.
-
Connect the LH front fog light electrical connector. Repeat this step for the RH side.
注Engage the locking tab.
- Install the front fascia assembly. See 饰板总成 - 前（拆下和安装）.
- Install the front license plate base bracket and front license plate molding painted bracket that was removed from the old fascia onto the new fascia. See 底座支架 - 车牌 - 前（拆卸和更换）.