2026-04-17

摄像头 - 后置 (HW4)（拆卸和更换）

校正代码 17222012 注意： 除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。 除非明确要求，否则请勿堆叠校正代码。 注意： 请参阅平均维修工时深入了解 FRT 及其创建方式。 注意： 请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意： 请参阅人体工程学注意事项查看安全健康的作业规程。

  • 2026-03-02: Updated calibration steps to use ServiceUI.
  • 2023-06-20: Switch the steps so that DAS Reset occurs directly before the Camera Connection Test.
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。

拆卸

  1. 打开 LH 前车门，降下 LH 前车窗。
  2. 启用“维护模式”。请参阅 维护模式（启用和禁用）。
  3. Partially open the liftgate.
    Informational PurposesAn informational icon, calling your attention
    注
    Allow the liftgate to open fully, and then pull the liftgate back to a comfortable working height.
  4. Apply masking tape around the liftgate applique to protect the painted surrounding area.
  5. Remove the bolts (x3) that attach the liftgate applique bracket to the liftgate.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • TP20 bit (Mini ratchet bit set - 1450424-00-A)
  6. Remove the liftgate applique bracket.
    Informational PurposesAn informational icon, calling your attention
    注
    Pull the bracket using the handle opening rearwards until the tabs back off from the liftgate.
  7. Disconnect the rear facing camera electrical connector.
    Informational PurposesAn informational icon, calling your attention
    注
    Push to lift the tab, and then disconnect the electrical connector.
  8. Remove the bolts (x2) that attach the rear facing camera to the liftgate applique bracket, and then remove the camera from the bracket.
    0.8 Nm (7 lbs-in)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • TP20 bit (Mini ratchet bit set - 1450424-00-A)

安装

  1. Carefully remove the old double sided tape, clean the body surface with Isopropyl Alcohol (IPA) wipes, and then install new double sided tape.
  2. Install the bolts (x2) that attach the rear facing camera to the liftgate applique bracket.
    0.8 Nm (7 lbs-in)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • TP20 bit (Mini ratchet bit set - 1450424-00-A)
  3. Secure the rear facing camera electrical connector on the liftgate applique bracket, and then connect the camera electrical connector.
  4. Unlock the vehicle gateway. See .
  5. Run PROC_DAS_X_CLEAR-CALIBRATIONvia Service Mode:
    • Driver Assist ➜ Cameras ➜ Clear Camera Calibration
    • Driver Assist ➜ Driverless ➜ Clear Calibration
    via Toolbox:(link)
  6. Run PROC_DAS_X_UPDATE-CAMERAvia Service Mode:Driver Assist ➜ Cameras ➜ Update Cameravia Toolbox:(link)
  7. Exit Service Mode.
  8. Install the liftgate applique bracket.
    1. Peel off the new double sided tape.
    2. Align the tabs to the liftgate holes, and then push the bracket into position.
    3. Apply pressure on the applique to help with the tape and bracket mating.
  9. Install the bolts (x3) that attach the liftgate applique bracket to the liftgate.
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • TP20 bit (Mini ratchet bit set - 1450424-00-A)
  10. Remove all masking tape from the vehicle after 5 minutes for the applique to properly adhere to the liftgate.
  11. Close the liftgate.
  12. 升起 LH 前车窗并关闭 LH 前车门。