校正代码 44015142 0.30 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。 注意：执行下述程序时，请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。

1. Open LH front door
2. Lower LH front window
3. Open LH rear door
4. Fold 60 seat into down position
   注

   Seat can be folded from the backrest button or trunk switch, If seat cushion is not present, protect the seat as required

   

5. Open liftgate
6. Remove parcel shelf

   

7. Remove trunk load floor

   

8. Remove side load floor trim

   

9. Remove the trunk sill panel
   注

   6x clips, 4x guides. Corners or bottom edge are good grabbing points for removal, Can use plastic trim tool or just your hands

   

   

   

10. Open charge port door using UI
    注

    Controls > Charging > Open Charge Port

    

11. Open hood
    注

    Via Center Display > Controls > Frunk Open

    

    

12. Remove rear underhood apron
    注

    8x clips

    

    

13. Disconnect LV power. See 低压电源（断开和连接）.
14. Perform the charge port voltage check procedure. See 充电接口电压检查.
15. Remove rear wall trim
    注

    4x push clips, 2x datums

    

    

    

16. Remove LH trunk bracket assembly
    注

    4x clips, 1 datum, Pull bracket straight up

    

    

    

17. Remove rear trunk floor

    

    

18. Remove LH side bolster trim
    注

    1x clip, 1x tab, Start by releasing upper portion

    

    

    

19. Separate LH C-pillar trim from LH upper C-pillar trim
    注

    4x clips, 4x datums

    

    

    

20. Release LH upper C-pillar trim and move aside
    注

    7x clips

    

    

    

21. Release clips securing LH trunk side trim and remove
    注

    3x push clips, 3x clips, 2x connectors

    

    

    

    

22. Remove charge port safety cap
    注

    3x tabs

    

    

    

23. Install charge port safety cap
    注

    3x tabs, Safety cap will click into position

    

    

    

    

24. Install LH trunk side trim and secure clips
    注

    3x push clips, 3x clips, 2x connections

    

    

    

    

25. Install LH upper C-pillar trim
    注

    7x clips, Replace any damaged clips

    

    

    

26. Secure LH C-pillar trim onto LH upper C-pillar trim
    注

    4x clips, 4x datums, Replace any damaged clips, Verify seated properly

    

    

    

27. Install LH side bolster trim
    注

    1x clip, 1x tab, Replace clip if damaged, Hook bottom portion and then secure the top

    

    

28. Install rear trunk floor

    

    

29. Install LH trunk bracket assembly
    注

    4x clips, 1 datum

    

    

    

30. Install rear wall trim
    注

    4x push clips, 2x datums

    

    

    

31. Install trunk sill panel
    注

    6x clips, 4x guides

    

    

    

32. Install side load floor

    

33. Install trunk load floor

    

34. Install parcel shelf

    

35. Close liftgate
36. Fold 60 seat into vertical position
    注

    Remove seat cushion protection

    

    

37. Close LH rear door
38. Connect First Responder Loop and LV battery connector
    注

    2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

    

    

    

    

39. Install rear underhood apron
    注

    8x clips

    

    

40. Close hood
    注

    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood

    

41. Raise LH front window
42. Close LH front door