校正代码 17451012 0.48 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。 注意：执行下述程序时，请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。

1. Open LH front door
2. Lower LH front window
3. Press brake pedal to turn on drive rails
4. Set air suspension ride height to “Very High”
   注

   Using center display > Controls > Suspension > ''Very High''
5. Turn wheel fully to the right
6. Open hood
   注

   Via Center Display > Controls > Frunk Open
7. Remove rear underhood apron
   注

   8x clips

   

   

8. Remove LH underhood apron
   注

   10x clips

   

   

9. Remove RH underhood apron
   注

   10x clips

   

   

10. Remove front underhood apron
    注

    7x clips

    

    

11. Remove bolts securing fascia bracket to carrier
    注

    6x bolts, 10mm, 4 Nm

    

12. Remove push clips securing LH front wheel arch liner to fascia and move to the side for access
    注

    5x push clips, Shift bottom of liner down and flex top of liner against tire

    

    

    

13. Remove bolt securing front fascia to LH fender bracket
    注

    1x bolt, T25, 5 Nm

    

14. Press brake pedal to turn on drive rails

    

15. Turn wheel fully to the left

    

16. Remove push clips securing RH front wheel arch liner to fascia and move to the side for access
    注

    5x push clips, Shift bottom of liner down and flex top of liner against tire

    

    

    

17. Remove bolt securing front fascia to RH fender bracket
    注

    1x bolt, T25, 5 Nm

    

18. Power off vehicle from center display
    注

    Via Controls > Safety & Security > Power Off

    

19. Disconnect LV battery connector and First Responder Loop
    注

    2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection

    

    

    

    

20. Disconnect front fascia harness
    注

    2x connectors, Pull red tab to disengage lock then disconnect, Located behind RH wheel arch liner

    

21. Release front fascia valance from front aero shield
    注

    3x bolts, 10mm, 6 Nm, 2x clips, 2x datums, Do not remove 3x middle bolts

    

    

22. Release fascia from fender brackets and pull forward to remove from vehicle
    注

    Set fascia on protected surface, Recommend assistance

    

    

23. Disconnect battery backed siren connector
    注

    1x connector

    

24. Remove bolt securing battery backed siren to front bumper beam complete
    注

    1x bolt, 10mm, 8 Nm

    

    

25. Install bolt securing battery backed siren to front bumper beam complete
    注

    1x bolt, 10mm, 8 Nm

    

    

26. Connect battery backed siren connector
    注

    1x connector

    

27. Install front fascia onto vehicle and secure fascia to fender brackets
    注

    Recommend Assistance, Route fascia harness while installing, Verify front fascia valance sits under front aero shield before proceeding

    

    

28. Apply Loctite 222 to fasteners and secure front fascia valance to front aero shield
    注

    3x bolts, 10mm, 6 Nm, 2x clips, 2x datums, Insert valance datums into aero shield holes, Do not remove 3x middle bolts

    

    

    

29. Connect front fascia harness
    注

    2x connectors, Engage locking tab, Located behind RH wheel arch liner

    

30. Install bolt securing fascia to RH fender bracket
    注

    1x bolt, T25, 5 Nm

    

31. Install push clips securing RH front wheel liner to fascia
    注

    5x push clips

    

    

32. Connect First Responder Loop and LV battery connector
    注

    2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

    

    

    

    

33. Press brake pedal to turn on drive rails

    

34. Turn wheel fully to the right
35. Install bolt securing fascia to LH fender bracket
    注

    1x bolt, T25, 5 Nm

    

36. Install push clips securing LH front wheel liner to fascia
    注

    5x push clips

    

    

37. Install bolts securing fascia bracket to carrier
    注

    6x bolts, 10mm, 4 Nm

    

38. Install RH underhood apron
    注

    10x clips

    

    

39. Install LH underhood apron
    注

    10x clips

    

    

40. Install rear underhood apron
    注

    8x clips

    

    

41. Close hood
    注

    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood

    

42. Press brake pedal to turn on drive rails
43. Turn steering wheel back to center
44. Set air suspension ride height to “Medium”
    注

    Using center display, Controls > Suspension > ''Medium'
45. Close LH front door