线束 - 正前方（欧洲、中东和非洲地区）(EMEA)（拆卸和更换）

Connect A/C machine to power and switch on

注

Touch time only, Machine will run various background tasks, Wait until Main Menu comes up before continuing

Skip the following panels when prompted

注

Use selections indicated in pictures

Perform hose flush

注

Touch time only, Connect couplers to machine, Open couplers by turning clockwise, Using Main Menu > Next > Menu > Flush hoses > Verify hose connection, Machine will chime once process is complete

Open LH front door

Lower LH and RH front windows

Using center display, place wipers into "Service Mode"

注

via Controls > Service > Wiper Service Mode

通过“维护模式”或 Toolbox 执行以下例行程序（请参阅面板执行器0005 - 维修模式）： PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN-REFRIGERANTvia Toolbox:(link)

注

Select "x" at the top right of the window to close once complete, Thermal Fill Drain routine has a 5 hour time limit, After 5 hours EXV's will close and routine must be performed again, Verify EXV positions are open via Garage > Vitals > HP > Refrigerant Loop EXV, Verify LCC, CC Left, Evap, CC Right, Chiller are all at ~100%. Recirc is at ~20%, LCC Solenoid is OPENED

Remove the underhood storage unit. See 前备箱储物单元（拆卸和安装）.

Remove caps from low side and high side AC ports

注

2x caps

Verify Thermal Fill Drain then connect hoses to vehicle and perform A/C recovery

注

First verify indicator displays green and vehicle is ready to be reclaimed, Connect couplers to vehicle, Note the amount of refrigerant and oil recovered, mark oil drain bottle oil level (use a piece of tape marking the fluid level), Open couplers by turning clockwise, Using Main Menu > Recover > Verify hose connection, Machine will chime once process is complete, Vehicle may be left unattended, Note or print the amount of refrigerant and oil recovered, Refrigerant recovered should be ~2.24 lb (1.02 kg), Oil recovered should be ~0.3 oz (8.87 mL), If drained oil level increased more than 1.01 oz (30 mL) refer to drained oil loss chart https://toolbox.teslamotors.com/articles/353700

Raise and support vehicle

注

Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads

Remove LH front wheel cap

注

Lift every other spoke at a time until cap is released from rim

Remove RH front wheel cap

注

Lift every other spoke at a time until cap is released from rim

Loosen RH front wheel

注

5x nuts, 21mm, 175 Nm

Loosen LH front wheel

注

5x nuts, 21mm, 175 Nm

Move LH front seat backward

Remove LH mid A-pillar trim

注

1x clip, 2x tabs

Remove LH lower A-pillar trim

注

7x clips

Remove LH footwell cover

注

1x connector, 2x magnets

Remove LH front floor mat

Remove LH console side carpet

注

11x clips

Release LH HEPA assembly lower dash bolt

注

1x bolt, 10mm, 7Nm

Open RH front door

Move RH front seat backward

Remove RH mid A-pillar trim

注

1x clip, 2x tabs

Remove RH lower A-pillar trim

注

7x clips

Remove RH footwell cover

注

3x magnets, 1x connector

Remove RH front floor mat

Remove RH console side carpet

注

11x clips

Fold RH front cabin carpet aside for access

Release harness from RH footrest panel

注

1x clip

Remove RH footrest panel

注

2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm

Release RH HEPA assembly lower dash bolt

注

1x bolt, 10mm, 7Nm

Release LH wiper arm hose nozzle

注

1x hose

Remove LH wiper arm nut cover

注

1x cover

Remove LH wiper arm nut and release assembly

注

1x nut, 15mm, 26 Nm

Release RH wiper arm hose nozzle

注

1x hose

Remove RH wiper arm nut cover

注

1x cover

Remove RH wiper arm nut and release assembly

注

1x nut, 15mm, 26 Nm

Release washer hose nozzle by LH shock tower cover

注

1x hose, 3x clips

Remove LH shock tower cover

注

3x push clips, 1x fir tree clip

Remove RH shock tower cover

注

3x push clips, 1x fir tree clip

Remove wiper cowl screen panel

注

4x push clips, 2x end tabs

Remove fasteners securing LH V-brace and remove assembly

注

3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm

Remove fasteners securing RH V-brace and remove assembly

注

3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm

Using center display, place wipers into "Service Mode"

注

via Controls > Service > Wiper Service Mode

Power off vehicle from center display

注

Via Controls > Safety & Security > Power Off

Disconnect LV battery connector and First Responder Loop

注

2x connectors, Lift up and release green locking tab, Pull black connector lock outwards to release connection

Remove wiper module

注

3x bolts, 10mm, 8 Nm, 1x connector, Rotate module forward and up to access connector, Observe LH wiper arm pivot during removal to avoid damage to windshield

Release clip securing the supermanifold to battery pump supply hose from LV battery

注

1x clip

Remove fasteners securing the LV battery and move aside

注

3x bolts, 10mm, 9 Nm, 2x datums, Take note of datums and carefully move assembly aside

Disconnect air quality sensor harness

注

1x connector

Remove HEPA filter assembly cover

注

2x tabs, 2x datums, 2x slots, , Be cautious and do not damage the mounting clips, Maneuver cover forward and up in front of V-brace cross member

Remove HEPA filter

注

2x clips, Release clips, Pivot filter forward and out of housing

Release V-brace crossmember

注

2x nuts, 10mm, 18 Nm

Remove HEPA housing assembly

注

2x nuts, 10mm, 7 Nm, Rotate V-brace cross member forward to create access to HEPA assembly retaining nuts, Maneuver assembly forward and up out of vehicle

Remove fasteners securing LH knee air bag assembly to vehicle

注

2x patch bolts, E10, 8 Nm, Discard after removal

Remove the LH knee air bag assembly from vehicle

注

3x connectors, 1x clip, 6x tabs, Release 2x locking tab on airbag connector

Fold LH front cabin carpet aside for access

Remove frunk harness ground from LH footwell area

注

1x nut, 10mm, 8 Nm

Disconnect J14 X036 Power connector

注

1x connector, Release lock then remove

Disconnect J9 X037 Frunk connector

注

1x connector

Remove fasteners securing RH knee air bag assembly to vehicle

注

2x patch bolts, E10, 8 Nm, Discard after removal

Remove RH knee air bag assembly from vehicle

注

2x connectors, 6x tabs, 1x clip, Release 2x locking tab on airbag connector

Install coolant hose clamps to coldplate hoses

注

2x hoses, Place coolant absorbent material around the car computer

Release coolant hoses from car computer coldplate assembly

注

2x spring locks, Install coolant plugs at both hoses and car computer

Remove car computer supply hoses through the bulkhead

注

Remove coolant hose clamps from car computer supply hose, Ensure plugs are secure and leak free, Guide hoses between HVAC assembly and bulkhead

Disconnect brown fakra connection from car computer

注

1x connector, X836

Disconnect frunk connectors on RH side of car computer

注

5x connectors

Release connectors at RH side of AP motherboard

注

3x connectors, Release locks on connectors before removal

Release frunk harness from RH footwell area

注

2x clips

Remove frunk harness ground from RH footwell area

注

1x nut, 10mm, 8 Nm

Disconnect J14 X056 Power connector

注

1x connector, Release lock then remove

Disconnect harness connectors

注

2x connectors, Release lock then remove

Release harness connector clips from RH controller

注

2x clips

Disconnect J9 X050 Frunk connector

注

1x connector,

Release electrical connections from TASC 2.0 ECU

注

3x connectors

Disconnect steering gear assembly connectors

注

2x connectors, Two-stage connectors, Slide red locking tab to unlock then depress connector release to disconnect

Remove AC hoses from vehicle

Remove Penta HVAC line from HVAC assembly

注

2x bolts, 13mm, 22 Nm

Raise vehicle partially and lower onto locks

注

Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

Remove RH front wheel

注

5x nuts, 21mm, 175 Nm

Remove LH front wheel

注

5x nuts, 21mm, 175 Nm

Remove LH front wheel liner

注

13x clips, 2x fan clips

Remove LH front jounce hose bracket from body

注

1x bolt, 10mm, 8 Nm

Disconnect LH front repeater

注

2x connectors

Release LH repeater harness from body

注

1x clip

Disconnect LH front ride height sensor

注

1x connector

Disconnect LH side ground junction connector (G500)

注

1x connector, Release red locking tab, Depress black tab and rotate lever to release

Disconnect LH Pedpro connection

注

1x connector

Disconnect LH front accelerator sensor

注

1x connector, Release red locking tab

Disconnect LH cooling fan module connector

注

1x connector, Disconnect this after coolant hoses are plugged to avoid coolant damaging connector

Release horn high tone connection

注

1x locking connector, Release red locking tab

Release horn low tone connection

注

1x locking connector, Release red locking tab

Disconnect frunk harness from washer system

注

2x Connectors, 3x Fir tree Clips, Disconnect connectors then remove the Fir Tree clips

Remove the RH front wheel liner

注

13x clips, Release clips, Remove from vehicle

Remove RH front jounce bracket from body

注

1x bolt, 10mm, 8 Nm

Disconnect RH front repeater

注

2x connectors

Release RH repeater harness from body

注

1x clip

Disconnect RH front ride height sensor

注

1x connector

Disconnect RH side ground junction connector

注

1x connector, Release red locking tab, Depress black tab and rotate lever to release

Disconnect RH Pedpro connections

注

1x connector

Disconnect RH cooling fan module connector

注

1x connector, Disconnect this after coolant hoses are plugged to avoid coolant damaging connector

Release frunk harness from RH wheel well area

注

1x clip

Release air compressor connections

注

2x connectors

Release air suspension valve block connector

注

1x connector

Release clips securing electrical harness to air compressor bracket

注

2x clips

Disconnect RH front accelerator

注

1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector

Disconnect front fascia harness

注

2x connectors, Pull red tab to disengage lock then disconnect, Located behind RH wheel arch liner

Release frunk harness from front end carrier

注

3x clips

Raise vehicle fully and lower lift onto locks

注

Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

Remove clips securing front aero shield to valence and HV battery

注

3x push clips

Remove bolts securing front aero shield and remove from vehicle

注

9x bolts, 10mm, 6 Nm

Disconnect EPAS CAN connectors

注

2x connectors, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector

Release frunk harness from subframe

注

3x clips, Route harness away from subframe

Remove bolts securing front skid plate to body sill

注

2x bolts, 15mm, 30 Nm

Remove bolts securing front skid plate to body casting

注

2x bolts, 15mm, 60 Nm

Remove bolts securing front skid plate to front subframe and remove skid plate

注

4x bolts, 15mm, 70 Nm, 2x bolts, 10mm, 10 Nm

Disconnect logic connector to HV battery

注

1x connector, Pull red locking tab outwards and release connection

Disconnect power connector to HV battery

注

1x connector, Pull red locking tab outwards and release connection

Release frunk harness from HV battery and body

注

2x clips

Lower vehicle partially and set lift onto locks

注

Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height

Disconnect RH headlamp connector

注

1x connector, Disengage red locking tab and pull red tab outwards to release

Disconnect FEM harness from RH side

注

1x connector, Release locking tab

Release frunk harness from top RH side of front end carrier and crash rail

注

2x clips

Release frunk harness from RH crash rail

注

2x clips

Disconnect RH front damper harness from frunk harness

注

1x connector

Release damper harness connector from RH crash rail

注

1x clip

Disconnect black connector on RH side of radiator along crash rail

注

1x connector, Release locking tab

Remove bolt securing RH side ground to RH side crash rail

注

1x bolt, 10mm, 8 Nm

Disconnect RH front wheel speed sensor from frunk harness

注

1x connector, 1x clip

Release frunk harness from frunk side of RH side crash rail

注

2x clips

Release upper connections on the front controller

注

2x locking connectors, Push in locking tabs and lift levers to release

Release LH middle connection on the front controller

注

1x locking connector, Push in locking tab and lift lever to release

Release RH middle connections on the front controller

注

2x locking connectors, Slide locking mechanism outwards to release

Release lower connections on the front controller

注

2x locking connectors, Slide red locking tab outwards to release

Remove bolt securing front controller ground cable

注

1x bolt, 10mm, 10 Nm

Remove bolts securing front controller

注

3x bolts, 10mm, 10 Nm

Remove front controller from vehicle and release ground cable from multi system beam

注

2x locating tabs, 1x ground cable

Disconnect module under vcright front

注

1x connector, release red locking tab, then pull again

Remove clips securing air suspension rear bundle to RH side of frunk harness

注

2x clips

Release RH front brake pipe from clips

注

5x clips, Do not bend pipe

Release battery coolant temp sensor connection

注

1x locking connector, Disengage red locking tab and slide tab outwards to release connection

Remove clip securing battery supply hose to RH side of frunk harness

注

1x clip

Release battery supply hose from battery coolant pump

注

1x hose clip, 2x plugs, Plug both ends

Release battery coolant pump connection

注

1x connector, Disengage red locking tab and slide tab outwards to release connection

Release frunk harness from RH front of body

注

3x clips

Release frunk harness from RH side of bulkhead

注

2x clips

Release grommet from RH side of bulkhead

注

1x grommet

Maneuver frunk harness branch through RH side of bulkhead

注

Move aside for clearance

Release branch routed to HV battery from below beam

注

1x clip, Follow hose downward to RH side body beam, Place clip prytool between clip and beam, Work clip out from bottom of beam, May need to slightly tap tool handle with hammer being cautious not to damage coolant hose

Release frunk body harness from FDU harness

注

1x locking connector, Release locking tab

Release clip securing frunk body harness to FDU LV harness bracket

注

1x clip

Release frunk harness from FDU assembly

注

1x clip

Disconnect LH headlamp connector

注

1x connector, Disengage red locking tab and pull red tab outwards to release

Disconnect frunk harness from LH side FEM harness connection

注

1x connector, Release red locking tab

Release frunk harness from top LH side of front end carrier

注

2x clips

Disconnect frunk harness from LH side crash rail

注

1x connector, Release locking tab

Release LH front damper harness connection

注

1x connector

Disconnect LH front wheel speed sensor from frunk harness

注

1x connector, 3x clips

Remove frunk harness ground from LH crash rail

注

1x bolt, 10mm, 8 Nm

Release frunk harness from LH side crash rail

注

4x clips

Release battery controller ground cable

注

1x bolt, 10mm, 9 Nm

Release harness clip from battery controller

注

1x fir tree clip

Remove fasteners securing battery controller and tilt controller for access

注

1x bolt, 10mm, 10 Nm, 1x nut, 10mm, 10 Nm

Release top J4 connection from battery controller

注

1x locking connector, Slide mechanism outwards to release

Release middle J5 connection from battery controller

注

1x locking connector, Push in locking tab and lift lever to release

Release side J3 connection from battery controller

注

1x locking connector, Slide mechanism outwards to release

Release middle J2 connection from battery controller

注

1x locking connector, Slide red locking tab outwards and release

Release side J1 connection from battery controller

注

1x locking connector, Slide red locking tab outwards and release

Release harness clip from battery controller

注

1x clip

Remove battery controller from vehicle

Release LV harness from multi system beam

注

1x bolt, 10mm, 8 Nm, 2x clips

Disconnect brake fluid level sensor

注

1x connector

Disconnect brake booster ECU connector

注

1x connector, Release red locking tab, then depress black tab and rotate lever to release

Disconnect the hydraulic control unit

注

1x connector, Release red locking tab and rotate lever upward to remove

Release grommet from LH side of bulkhead

注

1x grommet

Maneuver frunk harness branch through LH side of bulkhead

注

Move aside for clearance

Release frunk harness guide from bulkhead

注

2x clips

Release AC compressor HV harness clip from body

注

1x clip

Disconnect AC compressor logic connector

注

1x locking electrical connector, Do not push down on red tab, Pull to disengage lock, Pull again to release connector

Remove retaining clip securing AC compressor logic harness to AC compressor HV harness bracket

注

1x fir tree clip

Remove AC compressor ground strap

注

1x bolt, T25, 7 Nm

Release clip securing the coolant hose to the AC compressor bracket

注

1x fir tree clip

Release PT coolant pump connection

注

1x connector, Disengage red locking tab and slide tab outwards to release connection

Remove PT coolant pump from AC compressor bracket

注

Slide pump assembly away from compressor off lower bracket

Release compressor bracket from multi-system beam

注

2x bolts, 15mm, 31 Nm, Recommend assistance, Support the AC compressor while removing the fasteners, Carefully remove the AC compressor and AC compressor bracket towards the front of the vehicle and under the multi-system beam, Be cautious around the coolant hose and supermanifold harness, Place fender cover on fan housing and gently place AC compressor assembly down

Remove FDU ground strap from body stud

注

1x bolt, 12mm, 15 Nm, Remove strap assembly

Release frunk harness guide from LH side crash rail

注

2x clips

Support supermanifold using bungee cords

注

This is needed for frunk harness removal at later step, Be cautious to avoid damage to surrounding components

Remove bolts securing the supermanifold to the multi-system beam

注

2x bolts, 15 mm, 31 Nm, Recommend assistance, Support from underneath and at reservoir

Release multi-system beam

注

4x bolts, 15mm, 60 Nm

Place a folded rag underneath RH and LH side of the multi-system beam

注

Lift multi-system beam up only the amount required to clear the reservoir fill neck between top of supermanifold and bottom of beam, Recommend assistance if needed

Remove coolant bottle cap

Remove frunk harness from vehicle

注

Recommend assistance, Feed harness between mulit-system beam and super manifold, Maneuver harness to clear surrounding components, Move Bungee's around harness to allow clearance as needed

Install frunk harness into position

注

Feed harness between mulit-system beam and super manifold, Maneuver harness to clear surrounding components, Move Bungee's around harness to allow clearance as needed, Move each branch into place for installation

Maneuver frunk harness branch through LH side of bulkhead

注

1x grommet

Install frunk harness into LH side of bulkhead

注

1x grommet

Maneuver frunk harness branch through RH side of bulkhead

注

Position for installation

Secure frunk harness grommet into RH side of bulkhead

注

1x grommet

Route frunk harness towards HV battery and secure clip below beam

注

1x clip

Secure frunk harness onto RH side of crash rail

注

3x clips

Install frunk harness onto LH side crash rail

注

2x clips

Remove shop rags from underneath RH and LH side of the multi-system beam

Secure multi-system beam

注

4x bolts, 15mm, 60 Nm, Position beam and start bolts by hand

Install bolts securing the Supermanifold to the multi-system beam

注

2x bolts, 15 mm, 31 Nm, Recommend assistance, Support from underneath and at reservoir, Hand start bolts to Supermanifold

Remove bungee cords supporting supermanifold assembly

Install FDU ground strap to body stud

注

1x bolt, 12mm, 15 Nm, Position strap for install

Install bolts securing AC compressor bracket to multi system beam

注

2x bolts, 15mm, 31 Nm, Recommend assistance, Carefully support the AC compressor assembly and secure assembly, Prevent damage to any components, Remove any bungee cords

Secure AC compressor HV harness clip onto body

注

1x clip

Install AC compressor ground strap

注

1x bolt, T25, 7 Nm

Secure PT coolant pump onto AC compressor bracket

注

Slide pump assembly onto compressor lower bracket

Install clip securing the coolant hose to the AC compressor bracket

注

1x fir tree clip

Secure PT coolant pump connection

注

1x connector, Secure connector and full engage red locking tab

Install frunk harness onto LH side crash rail

注

4x clips

Install frunk harness ground onto LH crash rail

注

1x bolt, 10mm, 8 Nm

Connect LH front wheel speed sensor to frunk harness

注

1x connector, 3x clips

Secure LH front damper harness connection

注

1x connector

Connect frunk harness onto LH side crash rail

注

1x connector, Engage locking tab

Secure frunk harness onto top of LH side of front end carrier

注

2x clips

Connect frunk harness to LH side FEM harness connection

注

1x connector, Secure red locking tab

Connect LH headlamp connector

注

1x connector, Secure connector and fully engage red locking tab

Connect the hydraulic control unit

注

1x connector, Seat connection and rotate lever downward, then secure locking tab

Connect brake booster ECU connector

注

1x connector, Align connector and rotate lever to fully seat, Secure red locking tab

Install LV harness onto multi system beam

注

1x bolt, 10mm, 8 Nm, 2x clips

Position battery controller into vehicle

Secure harness clip onto battery controller

注

1x clip

Secure side J1 connection onto battery controller

注

1x locking connector, Engage red locking tab

Secure middle J2 connection onto battery controller

注

1x locking connector, Engage red locking tab

Secure side J3 connection onto battery controller

注

1x locking connector, Verify yellow locking tab is fully opened, Seat connector and mechanism will begin to engage

Secure middle J5 connection onto battery controller

注

1x locking connector, Verify lever is fully opened, Seat connector and lever will being to engage

Secure top J4 connection onto battery controller

注

1x locking connector, Verify yellow locking tab is fully opened, Seat connector and mechanism will begin to engage

Secure harness clip onto battery controller

注

1x clip

Secure battery controller ground cable

注

1x bolt, 10mm or E10 5-lobe, 9 Nm

Position battery controller forward and install fasteners

注

1x bolt, 10mm, 10 Nm, 1x nut 10mm, 10 Nm

Secure frunk harness onto FDU

注

1x clip

Install clip securing frunk body harness to FDU LV harness bracket

注

1x clip

Secure frunk body harness onto FDU harness

注

1x connector, Engage red locking tab

Install frunk harness guide onto bulkhead

注

3x clips

Secure RH front brake pipe onto clips

注

5x clips, Do not bend pipe

Secure frunk harness onto RH side of bulkhead

注

2x clips

Install clips securing air suspension rear bundle to RH side of frunk harness

注

2x clips

Secure car computer supply hoses to the bulkhead

注

Guide hoses between HVAC assembly and bulkhead, Ensure grommet is fully seated into bulkhead

Secure battery coolant pump connection

注

1x connector, Secure connector and full engage red locking tab

Secure battery coolant pump to bracket

注

1x clip, Slide pump on to bracket and secure lower coolant hose to bracket

Install clip securing battery supply hose to frunk harness

注

1x clip

Secure battery coolant temp sensor connection

注

1x locking connector, Secure connector and fully engage red locking tab

Secure three way valve connection

注

1x locking connector, Secure connector and fully engage red locking tab

Position front controller for installation and position ground cable

注

2x locating tabs, 1x ground cable

Install bolts securing front controller

注

3x bolts, 10mm, 10 Nm. Start with the side bolt

Install bolt securing front controller ground cable

注

1x bolts, 10mm, 10 Nm

Secure lower connections on the front controller

注

2x locking connectors, Engage red locking tab

Secure RH middle connections on front controller

注

2x locking connectors, Verify yellow locking tabs are fully opened, Seat connectors and mechanism will begin to engage

Secure LH middle connection for front controller

注

1x locking connector, Verify lever is fully opened, Seat connector and lever will being to engage

Secure upper connections for the front controller

注

2x locking connectors, Verify levers are fully opened, Seat connectors and levers will begin to engage

Install frunk harness onto RH side crash rail

注

2x clips

Connect RH front wheel speed sensor to frunk harness

注

1x connector, 3x clips

Install bolt securing RH side ground to RH side crash rail

注

1x bolt, 10mm, 8 Nm

Connect black connector on RS of radiator along crash rail

注

1x connector, Engage locking tab

Secure damper harness connector onto RH crash rail

注

1x clip

Connect RH front damper harness

注

1x connector

Secure frunk harness onto RH crash rail

注

2x clips

Secure frunk harness onto top RH side of front end carrier and crash rail

注

2x clips

Connect frunk harness to RH side FEM harness connection

注

1x connector, Engage red locking tab

Connect RH headlamp connector

注

1x connector, Secure connector and fully engage red locking tab

Raise vehicle fully and lower lift onto locks

注

Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

Secure frunk harness onto HV battery and body

注

2x clips

Secure power connector to HV battery

注

1x connector, Engage red locking tab

Secure logic connector to HV battery

注

1x connector, Engage red locking tab

Position front skid plate for installation and thread in all bolts

注

4x bolts, 15mm, 70 Nm, 2x bolts, 15mm, 60 Nm, 2x bolts, 15mm, 30 Nm, 2x bolts, 10mm, 10 Nm, Torque at later step

Torque bolts securing front skid plate to body casting

注

2x bolts, 15mm, 60 Nm

Torque bolts securing front skid plate to body sill

注

2x bolts, 15mm, 30 Nm

Secure frunk harness onto subframe

注

3x clips

Connect EPAS CAN connectors

注

2x connectors, Engage locking tab

Apply Loctite 222 onto front aero shield bolts and install fasteners securing front aero shield to vehicle

注

9x bolts, 10mm, 6 Nm

Install clips securing front aero shield to valence and HV battery

注

3x push clips

Lower vehicle partially and set lift onto locks

注

Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height

Secure frunk harness onto front end carrier

注

3x clips

Connect front fascia harness

注

2x connectors, Engage locking tab, Located behind RH wheel arch liner

Connect RH front accelerator

注

1x connector, Engage locking tab

Install clips securing electrical harness to air compressor bracket

注

2x clips

Secure air suspension valve block connector

注

1x connector

Secure air compressor connections

注

2x connectors

Secure frunk harness onto RH wheel well area

注

1x clip

Install RH cooling fan module connector

注

1x connector

Connect RH side Pedpro connection

注

1x connector

Connect RH ground junction connector

注

1x connector, Secure red locking tab

Connect RH front ride height sensor

注

1x connector

Secure RH repeater harness to body

注

1x clip

Connect RH front repeater

注

2x connectors, Support repeater from exterior to prevent damage to retaining clips

Install RH front jounce bracket to body

注

1x bolt, 10mm, 8 Nm

Install RH front wheel liner

注

13x clips

Connect frunk harness to washer system

注

2x Connectors, 3x Fir tree Clips

Secure horn low tone connection

注

1x locking connector, Verify fully seated and engage red locking tab

Secure horn high tone connection

注

1x locking connector, Verify fully seated and engage red locking tab

Install LH cooling fan module connector

注

1x connector

Connect LH front accelerator sensor

注

1x connector, Engage red locking tab

Connect LH side Pedpro connection

注

1x connector

Connect LH ground junction connector

注

1x connector, Secure red locking tab

Connect LH front ride height sensor

注

1x connector

Secure LH repeater harness to body

注

1x clip

Connect LH front repeater

注

2x connectors, Support repeater from exterior to prevent damage to retaining clips

Install LH front jounce hose bracket to body

注

1x bolt, 10mm, 8 Nm

Install LH front wheel liner

注

13x clips

Install LH front wheel

注

5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool

Install RH front wheel

注

5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool

Lower vehicle until tires are touching the ground

注

Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

Install Penta HVAC line from HVAC assembly

注

2x bolts, 13mm, 22 Nm

Reconnect AC hoses to vehicle

Verify Thermal Fill Drain then Perform AC vacuum and run leak test

注

First verify indicator displays green if it is vehicle is ready for vacuum, Set vacuum time to 15 minutes and leak test to ON, Machine will chime once process is complete, Vehicle may be left unattended, Verify leak test passed before continuing

Install HEPA housing assembly

注

2x nuts, 10mm, 7 Nm, Maneuver assembly down and under cross member, Rotate V-brace crossmember bracket back to install position

Secure V-brace crossmember

注

2x nuts, 10mm, 18 Nm

Install HEPA filter

注

3x datums, 2x clips, Align 3 datums into bottom of housing, Confirm air flow direction, Ensure clips lock and secure filter into housing

Install HEPA filter assembly cover

注

2x tabs, 2x datums, 2x slots, Maneuver cover down and under V-brace cross member, Fully engage seal and locking tabs

Connect air quality sensor harness

注

1x connector

Install fasteners securing LV battery to multi-system beam

注

3x bolts, 10mm, 9 Nm, 2x datums, Shift into position and install fasteners

Install clip securing the supermanifold to battery pump supply hose onto LV battery

注

1x clip

Install wiper module

注

3x bolts, 10mm, 8 Nm, 1x connector, Secure electrical connector first, Rotate module rearward and under windshield, Observe LH wiper arm pivot during install to avoid damage to windshield

Connect steering gear assembly connectors

注

2x connectors, Two-stage connectors, Ensure locking tab is engaged after an audible click is heard when connecting

Secure coolant hoses to car computer coldplate assembly

注

2x spring locks, Remove coolant plugs and absorbent material, Ensure spring locks engage and perform pull-push-pull test on each hose coupling

Secure electrical connections to TASC 2.0 ECU

注

3x connectors

Connect J9 X050 Frunk connector

注

1x connector

Secure harness connector clips onto RH controller

注

2x clips

Connect harness connectors

注

2x connectors, Fully seat connector then engage lock

Connect J14 X056 Power connector

注

1x connector, Fully seat connector then engage lock

Install bolt securing frunk harness ground near RH footwell area

注

1x bolt, 10mm, 8 Nm

Secure frunk harness onto RH footwell area

注

2x clips

Install connectors at RH side of AP motherboard

注

3x connectors

Connect frunk connectors on RH side of car computer

注

5x connectors

Connect brown fakra connection onto car computer

注

1x connector, X836

Secure RH HEPA assembly lower dash bolt

注

1x bolt, 10mm, 7Nm

Install RH footrest panel

注

2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm

Secure harness to RH footrest panel

注

1x clip

Fold RH main carpet back into place

Install RH console side carpet

注

11x clips

Install RH front floor mat

Install RH footwell cover

注

3x magnets, 1x connectors

Install RH lower A-pillar trim

注

7x clips, Verify weather seal is seated properly

Install RH mid A-pillar trim

注

1x clip, 2x tabs, Verify weather seal is seated properly

Fold RH main carpet back into place

Install RH knee air bag assembly into vehicle

注

2x connectors, 6x tabs, 1x clip, Hook tabs before fully seating, Use caution not to damage the connector/harness, Support the knee air bag while connecting the connector

Install fasteners securing RH knee air bag assembly to vehicle

注

2x patch bolts, E10, 8 Nm, Install new fasteners

Connect J9 X037 Frunk connector

注

1x connector

Connect J14 X036 Power connector

注

1x connector, Fully seat connector then engage lock

Install frunk harness ground onto LH footwell area

注

1x bolt, 10mm, 8 Nm

Secure LH HEPA assembly lower dash bolt

注

1x bolt, 10mm, 7 Nm

Fold LH main carpet back into place

Install LH front floor mat

Install LH footwell cover

注

1x connector, 2x magnets

Install LH lower A-pillar trim

注

7x clips, Verify weather seal is seated properly

Install LH console side carpet

注

11x clips

Install LH mid A-pillar trim

注

1x clip, 2x tabs, Verify weather seal is seated properly

Install the LH knee air bag assembly into vehicle

注

1x clip, 3x connectors, 6x tabs, Hook tabs before fully seating, Use caution not to damage the connector/harness, Support the knee air bag while connecting the connectors

Install fasteners securing LH knee air bag assembly to vehicle

注

2x patch bolts, E10, 8 Nm, Install new fasteners

Select "refrigerant charge" on AC machine

注

Select the arrows under "refrigerant charge", Enter refrigerant amount of 1.02 kg (1020 g)

Connect First Responder Loop and LV battery connector

注

2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

Using center display, remove wipers from "Service Mode"

Install fasteners securing LH V-brace and secure

注

3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm

Install fasteners securing RH V-brace and secure

注

3x bolts, 10mm, 18 Nm, 1x nut, 10mm, 9 Nm

Install wiper cowl screen panel

注

4x push clips, 2x end tabs

Install wiper cowl screen panel

注

4x push clips, 2x end tabs

Install RH wiper arm assembly and secure nut

注

1x nut, 15mm, 26 Nm, Line up wiper to reference mark on windshield

Install RH wiper arm nut cover

Secure RH wiper arm washer nozzle

注

1x hose, Hose is routed below the arm

Install LH wiper arm assembly and secure nut

注

1x nut, 15mm, 26 Nm, Line up wiper to reference mark on windshield

Install LH wiper arm nut cover

Secure LH wiper arm washer nozzle

注

1x hose, Hose is routed below the arm

Secure washer hose nozzle by LH shock tower cover

注

1x hose, 3x clips

Install LH shock tower cover

注

3x push clip, 1x fir tree clip

Install RH shock tower cover

注

3x push clip, 1x fir tree clip

Inspect coolant level and top off as necessary

注

Ensure that the fluid level is at the Max line, Top off fluid as required

Move RH front seat to original position

Close RH front door

通过“维护模式”或 Toolbox 执行以下例行程序（请参阅面板执行器0005 - 维修模式）： TEST-SELF_VCFRONT_X_HEAT-PUMP-COMMISSIONINGvia Service Mode:Thermal ➜ Refrigerant System ➜ Commission Heat Pumpvia Service Mode Plus:Drive Inverter ➜ Front Drive Inverter Replacement ➜ Heatpump commissioningvia Toolbox:(link)

注

If this routine is not run after entering Thermal Drain/Fill mode, the AC compressor operation will be blocked, Select ‘X’ at top right of window to close once complete

Proceed with Hose Equalize steps to complete AC recharge process and follow instructions displayed on AC Machine

注

Disconnect high side coupler from vehicle, Turn AC on, Temp setting LO, Panel mode on, Fresh air mode on, Blower speed set to 10, Verify Hose Equalize settings, Verify discharge pressure does not exceed 26 bar and suction pressure is not below 1.15 bar,

Proceed with Hose Equalize steps to complete AC recharge process and follow instructions displayed on AC Machine

注

Remove low side coupler from vehicle, Turn vehicle off, Verify Hose Equalize settings, Machine will chime once process is complete

Install caps onto AC ports

注

2x caps

通过“维护模式”或 Toolbox 执行以下例行程序（请参阅面板执行器0005 - 维修模式）： TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Service Mode:

Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
Thermal ➜ Coolant System ➜ Coolant Purge Start

via Service Mode Plus:

Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge

via Toolbox:(link)

通过“维护模式”或 Toolbox 执行以下例行程序（请参阅面板执行器0005 - 维修模式）： TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Service Mode:Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus: