Harness - Pyrotechnic - HV Battery (Remove and Replace)
校正代码
16300062
5.10
NOTE: Unless otherwise explicitly
stated in the procedure, the above correction code and FRT reflect all of the work
required to perform this procedure, including the linked procedures. Do not stack correction codes unless
explicitly told to do so.
NOTE: See 平均维修工时 to learn
more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com.
NOTE: See 人员保护 to make sure proper PPE is worn when
performing the below
procedure.
拆卸
- 将车辆驶至双柱举升机上。请参阅Raise Vehicle - 2 Post Lift。
- 执行冷却系统热加注排空。请参阅Thermal Fluid - Cooling System (Fill/Drain)。
- 拆卸左右门槛板防擦板。请参阅Scuff Plate - Rocker Panel - LH (Remove and Replace)。
- 拆卸左右门槛板饰条。请参阅Molding - Rocker Panel - LH (Remove and Replace)。
- 放置双柱举升机垫,以便拆卸高压电池。
- 拆卸前备箱后部挡板。请参阅Underhood Apron - Rear (Remove and Replace)。
- 断开低压电源。请参阅LV Power (Disconnect and Connect)。
- 拆卸中间流线型护板。请参阅Panel - Aero Shield - Rear (Remove and Replace)。
- 执行车辆高压禁用程序。请参阅Vehicle HV Disablement Procedure。
- 拆下烟火电池断接开关。请参阅Pyrotechnic Battery Disconnect (Remove and Replace)。
- 拆下高压电池。请参阅HV Battery (AWD) (Remove and Install)。
- 执行功率转换系统冷却液排放。请参阅Power Conversion System Coolant (Drain)。
- 拆下高压电池前检修板。请参阅Cover - Front Access - HV Battery (Remove and Install)。
- 拆卸功率转换系统。请参阅Power Conversion System (Remove and Replace)。
- 拆下将功率转换系统安装托盘固定到高压电池的螺栓(6 个),然后从高压电池上拆下托盘。
- 揭下 Kapton 胶带,然后从母排和绝缘体上取下云母屏蔽罩。
- 从高压控制器上松开高压电池烟火线束夹和贴片锚固件。
- 断开高压电池烟火线束与高压控制器连接器之间的连接。
-
断开电气线束与高压控制器连接器之间的连接。
注断开电气线束有便于拆卸高压电池烟火线束。
- 小心地从前托盘外壳上松开高压电池烟火线束连接器。
- 松开将高压电池烟火线束固定到母排两侧前托盘外壳的夹子(2 个)。
- 将高压电池烟火线束从母排下方拆下,并从高压电池中取出。
安装
- 将高压电池烟火线束安装在母排下方。
- 紧固将高压电池烟火线束固定到母排两侧前托盘外壳的夹子(2 个)。
- 小心地将高压电池烟火线束连接器固定到前托盘外壳上。
- 将电气线束连接到高压控制器连接器。
- 将高压电池烟火线束连接到高压控制器连接器。
- 用酒精湿巾清洁高压控制器顶部的粘贴片区域,并等待风干至少 1 分钟。
- 紧固高压电池烟火线束夹,揭下保护条,并将贴片锚固件固定在高压控制器上。
-
将云母屏蔽罩安装到母排和绝缘体上。
注如有必要,使用新的 Kapton 胶带。
-
将功率转换系统安装托盘安装到高压电池中,然后安装将托盘固定到高压电池的螺栓(6 个)。8 Nm (5.9 lbs-ft)注确保托盘下没有夹住任何电线。
- 安装功率转换系统。请参阅Power Conversion System (Remove and Replace)。
- 安装高压电池前检修板。请参阅Cover - Front Access - HV Battery (Remove and Install)。
- 测量烟火电池断接开关安装点间的电压,然后安装烟火电池断接开关。请参阅Pyrotechnic Battery Disconnect (Remove and Replace)。
- 执行功率转换系统冷却液泄漏测试。请参阅Power Conversion System Coolant Leak Test (On Table)。
- 执行高压电池漏气测试。请参阅HV Battery Air Leak Test (On Table)。
- 安装高压电池。请参阅HV Battery (AWD) (Remove and Install)。
- 安装中间流线型护板。请参阅Panel - Aero Shield - Rear (Remove and Replace)。
- 连接低压电源。请参阅LV Power (Disconnect and Connect)。
- 安装前备箱后部挡板。请参阅Underhood Apron - Rear (Remove and Replace)。
- 安装左右门槛板饰条。请参阅Molding - Rocker Panel - LH (Remove and Replace)。
- 安装左右门槛板防擦板。请参阅Scuff Plate - Rocker Panel - LH (Remove and Replace)。
- 将车辆驶离双柱举升机。请参阅Raise Vehicle - 2 Post Lift。