2024-11-18

Cooling System (Partial Refill and Bleed)

校正代码 18300000 0.15 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See 平均维修工时 to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure proper PPE is worn when performing the below procedure.

Warning IconA warning icon, calling your attention to a possibly risky situation
警告
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.

程序

  1. 通过“维护模式”或 Toolbox 执行以下例行程序(请参阅面板执行器0005 - 维修模式): PROC_VCFRONT_X_START-THERMAL-FILL-DRAIN-COOLANTvia Toolbox: (link)via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Start Fluid Fill/Drain
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Start Fluid Fill/Drain
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Start Fluid Fill/Drain
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Start Fluid Fill/Drain
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Start Coolant Fill/Drain
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Start Coolant Fill/Drain
  2. 拆下前备箱后部挡板。请参阅Underhood Apron - Rear (Remove and Replace)
  3. 拆卸冷却液罐罐盖。
  4. 确保冷却液液位处于 Max 线处,必要时加满。
  5. 通过“维护模式”或 Toolbox 执行以下例行程序(请参阅面板执行器0005 - 维修模式): TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    Informational PurposesAn informational icon, calling your attention
    确保驱动导轨处于关闭状态。打开驱动导轨将停止例程。
    Informational PurposesAn informational icon, calling your attention
    例程运行期间,监测冷却液罐,根据需要添加冷却液,使液位保持在 NOM 和 MAX 之间。
    Informational PurposesAn informational icon, calling your attention
    空气净化持续约 10 分钟。
  6. 如果需要进行热性能检查,请继续进行下一步,否则,跳到第 8 步。
  7. 通过“维护模式”或 Toolbox 执行以下例行程序(请参阅面板执行器0005 - 维修模式): TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Toolbox: (link)via Service Mode: Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    Informational PurposesAn informational icon, calling your attention
    如果热性能测试失败,请参阅 Toolbox 文章 #206000。
  8. 确保冷却液液位处于 MAX 线处,必要时加满。
  9. 安装冷却液罐罐盖。
  10. 安装前备箱后部挡板。请参阅Underhood Apron - Rear (Remove and Replace)
  11. 禁用“维护模式”。请参阅Service Mode (Enable and Disable)