2025-07-03
Umbrella Valve - Set (Remove and Replace)
校正代码
16102742
0.66
注意:除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。
注意:请参阅平均维修工时,深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈,请发送电子邮件至ServiceManualFeedback@tesla.com。
注意:请参阅人员保护,确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
警告
本程序为“草案”。虽已通过验证,但可能仍有“警告”和“注意”事项缺失。请遵守安全要求,处理或靠近高压系统和部件时,请谨慎操作。请将校正内容及反馈发送至ServiceDevelopment@teslamotors.com。
- 2025-05-12: Released new procedure.
拆卸
- Open the front doors and lower the front windows.
- Open the RH rear door.
- Remove the RH rocker panel molding. See 饰条 - 门槛板 - LH(拆卸和更换).
- Raise and support the vehicle. See 举升车辆 - 双柱举升机.
- Remove the mid aero shield panel. See 面板 - 流线型护板 - 后部(拆卸和更换).
-
Remove the umbrella valves (x5) from the RH side of the HV battery.
警告If liquid is observed leaking from the valve during removal, immediately halt the procedure and consult Toolbox article 5401800 for further instructions.注Use a plastic trim tool to unlock the umbrella valve clips from the thermal vent.
安装
-
Use IPA wipes to thoroughly clean the thermal vent openings (x5).
警告Make sure no dirt or debris enters the HV battery enclosure during cleaning.注Remove any debris that may have built up. Allow 1 minute of dry time.
-
Use a gloved finger to apply grease (PN: 1024173-00-A) around the perimeter of each thermal vent opening (x5).
警告Make sure that there are no empty gaps in the grease application.
- Make sure to only use new umbrella valves. Refer to image for how to identify new parts.
-
Inspect the new umbrella valves for proper assembly.
注Reject any incorrectly assembled parts. Only use reworked parts if they match the “Good” requirements. To check if the thermal vent is properly pre-assembled, rotate the umbrella around the clamp. If it rotates smoothly without any resistance, the installation is correct. If there is any resistance, even slight, the installation is incorrect. To fix it, push the umbrella more firmly onto the clamp.
-
Install the new umbrella valves (x5) into the HV Battery.
注Push the valve into the thermal vent opening with the legs facing inward. Confirm all three legs are clipped into the opening with an audible click. Push the umbrella into HV battery enclosure after verification.
-
Perform the HV battery leak test. See 高压电池漏气测试(车上).
警告While the HV battery is pressurized, inspect each umbrella valve for escaping air. Perform the following test regardless of leak test results.
- Place a hand over each umbrella valve to feel for escaping air.
- Spray soapy water over each umbrella valve and inspect for bubbles.
If leaks are found, replace the umbrella valve as needed.
If no leaks from any of the umbrella valves are found, but the HV battery leak test is failing, refer to Toolbox article 5402000 for further diagnoses.
- Install the mid aero shield panel. See 面板 - 流线型护板 - 后部(拆卸和更换).
- Remove the vehicle from the lift. See 举升车辆 - 双柱举升机.
- Install the RH rocker panel molding. See 饰条 - 门槛板 - LH(拆卸和更换).
- Close the doors and raise the windows.