2025-07-03

万向节 - 悬架 - 后 - LH(拆卸和更换)

校正代码 31030102 1.50 注意: 除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。 除非明确要求,否则请勿堆叠校正代码。 注意: 请参阅平均维修工时,深入了解 FRT 及其创建方式。 要提供有关 FRT 值的反馈,请发送电子邮件至ServiceManualFeedback@tesla.com。 注意: 执行下述程序时,请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。

扭矩规格

表 1. 扭矩规格悬架 - 后(扭矩)
描述 扭矩值 推荐工具 重新使用/更换 备注
将后下尾连杆固定到转向节的螺母和螺栓
150 Nm (110.6 lbs-ft)
  • 21 毫米套筒
重新使用
Informational PurposesAn informational icon, calling your attention
2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
将后止推杆固定到转向节的螺母和螺栓
150 Nm (110.6 lbs-ft)
  • 21 毫米套筒
重新使用
Informational PurposesAn informational icon, calling your attention
2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
将后下前连杆固定到转向节的螺母和螺栓
150 Nm (110.6 lbs-ft)
  • 21 毫米套筒
重新使用
Informational PurposesAn informational icon, calling your attention
2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
将后上前连杆固定到转向节的螺母和螺栓
150 Nm (110.6 lbs-ft)
  • 21 毫米套筒
重新使用
Informational PurposesAn informational icon, calling your attention
2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
将后上尾连杆固定到转向节的螺母和螺栓
150 Nm (110.6 lbs-ft)
  • 21 毫米套筒
重新使用
Informational PurposesAn informational icon, calling your attention
2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
将后空气弹簧模块固定到转向节的螺母和螺栓
140 Nm (103.2 lbs-ft)
  • 21 毫米套筒
重新使用
Informational PurposesAn informational icon, calling your attention
2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
将后转向节线束支架固定到转向节的螺栓 (x2)
5 Nm (3.7 lbs-ft)
  • 梅花 T30 套筒
重新使用
将后主动降噪 (ANC) 传感器固定到转向节的螺栓
6 Nm (4.4 lbs-ft)
  • 10 毫米套筒
重新使用
将后轮毂转速传感器固定到转向节的螺栓
5 Nm (3.7 lbs-ft)
  • 梅花 T30 套筒
重新使用

拆卸

  1. 举升并支撑车辆请参阅 举升车辆 - 双柱举升机
  2. 松开驻车制动卡钳。请参阅 驻车制动钳 - 释放
  3. 拆下 LH 后车轮中心盖板。
  4. 松开左后车轴螺母。
  5. 拆下 LH 后车轮。请参阅 轮毂总成(拆卸和安装)
  6. 拆下左侧后制动卡钳和制动盘。请参阅 制动盘 - 后 - 套件(拆卸和更换)
  7. 拆下 LH 后轮毂。请参阅 轮毂轴承 - 后 - LH(拆卸和更换)
  8. 拆下 LH 后制动防尘罩。请参阅 罩 - 防尘 - 制动 - 后 - LH(拆卸和更换)
  9. 断开电气线束连接器(2 个)和线束与左侧后主动减震器的连接。
  10. 松开将电气线束固定到 LH 后转向节的夹子。
  11. 拆下将车轮转速传感器固定到 LH 后转向节的螺栓。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T30 套筒
  12. 断开左侧后主动降噪 (ANC) 传感器,然后拆下将左侧后主动降噪 (ANC) 传感器固定到转向节的螺栓。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    切勿向下按压红色锁片。将锁片拉离连接器,直至连接器解锁,然后继续拉动以松开连接器。
  13. 拆下将左侧后转向节线束支架固定到车辆的螺栓(2 个),然后将电气线束与支架一起移至一旁。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T30 套筒
  14. 拆下将左侧后空气弹簧模块固定到转向节的螺母。
    Informational PurposesAn informational icon, calling your attention
    请勿在此时拆下螺栓。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  15. 拆下将左侧后上部前连杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 16 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  16. 拆下将左侧后止推杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  17. 拆下将左侧后下部前连杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  18. 拆下将左侧后上部尾连杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  19. 拆下将左侧后下部尾连杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  20. 拆下将空气支撑杆固定到转向节的螺栓,然后从车辆上拆下左侧后转向节。

安装

  1. 清洁车轴的外侧,并在车轴上涂抹不超过 1 克的 Molykote M-77。
  2. 安装将左侧后下部尾连杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    该螺栓将在后续步骤中拧紧。
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  3. 安装将左侧后止推杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    该螺栓将在后续步骤中拧紧。
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  4. 安装将左侧下部前连杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    该螺栓将在后续步骤中拧紧。
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  5. 安装将左侧上部前连杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    该螺栓将在后续步骤中拧紧。
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  6. 安装将左侧后上部尾连杆固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    该螺栓将在后续步骤中拧紧。
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  7. 安装将左侧后空气弹簧模块固定到转向节的螺母和螺栓。
    Informational PurposesAn informational icon, calling your attention
    该螺栓将在后续步骤中拧紧。
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  8. 安装左侧后制动防尘罩。请参阅 罩 - 防尘 - 制动 - 后 - LH(拆卸和更换)
  9. 安装 LH 后轮毂。请参阅 轮毂轴承 - 后 - LH(拆卸和更换)
  10. 安装左侧后制动盘和制动钳。请参阅 制动盘 - 后 - 套件(拆卸和更换)
  11. 用手拧紧将半轴固定到后轮毂的车轴螺母和新垫圈。
    Informational PurposesAn informational icon, calling your attention
    车轴螺母将在后续步骤中拧紧。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 32 毫米深冲击套筒
  12. 使用带耳螺母将轮毂轴承千斤顶适配器安装到左后轮毂轴承上。
  13. 放置并升起支架,以模拟左后悬架位于行驶高度的情况。
  14. 测量从上前连杆到车架纵梁上螺栓的距离,确保左侧悬架设置为行驶高度。
    Informational PurposesAn informational icon, calling your attention
    此距离应该为 85 毫米 +/- 5 毫米。
  15. 紧固将左后止推杆固定到转向节的螺栓,然后用油性记号笔标记螺栓。
    150 Nm (110.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  16. 紧固将左后上前连杆固定到转向节的螺栓,然后用油性记号笔标记螺栓。
    150 Nm (110.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  17. 紧固将左后下尾连杆固定到转向节的螺栓,然后用油性记号笔标记螺栓。
    150 Nm (110.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  18. 紧固将左后下前连杆固定到转向节的螺栓,然后用油性记号笔标记螺栓。
    150 Nm (110.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  19. 紧固将左后上尾连杆固定到转向节的螺栓,然后用油性记号笔标记螺栓。
    150 Nm (110.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  20. 紧固将左侧减震器固定到转向节的螺栓,然后用油性记号笔标记螺栓。
    140 Nm (103.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 21 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    2025+ Model S 车型转向节的某些连接点会使用到卡式旗形螺母。
  21. 降低支架,直至悬架空载,然后将支架从车上拆下。
  22. 将轮毂轴承千斤顶适配器从轮毂轴承上拆下。
  23. 布置并安装将左后转向节线束支架固定到转向节的螺栓(2 个)。
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T30 套筒
  24. 装将左后主动降噪 (ANC) 传感器固定到转向节的螺栓。
    6 Nm (4.4 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米套筒
  25. 将电气线束连接到 LH 后 ANC 传感器。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    将红色锁片推入连接器中以接合连接器锁。
  26. 安装将轮毂转速传感器固定到左后转向节的螺栓。
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T30 套筒
  27. 放置好将电气线束固定到 LH 后转向节的夹子。
  28. 将电气线束连接到左侧后主动减震器。
  29. 安装 LH 后车轮。请参阅 轮毂总成(拆卸和安装)
  30. 降下车辆,直至轮胎与地面接触。
  31. 拧紧车轴螺母。
    245 Nm (180.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 32 毫米深冲击套筒
  32. 安装左后车轮盖,对齐阀杆和车轮盖。
  33. 触摸并长按车辆显示屏上的“Park”按钮以退出 EPB 维护模式。
  34. 将车辆驶离双柱举升机。
  35. 请参阅“定位要求”表,确定是否需要进行电动助力转向 (EPAS) 定位检查 (EC) 或四轮定位检查 (AC)。如果已执行,请作为一项单独的工项添加定位检查/调整。请参阅定位要求 - 悬架