2026-07-31

同轴电缆 - 侧转向灯 - 前 - 左右两侧（更换） ((拆卸和更换))

校正代码 17403032 FRT 2.16 注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

警告

本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。

2026-07-09: Released new procedure.

Overlay

Open both front doors and lower both front windows.
Remove the wiper module. See 雨刮器模块（拆卸和更换）.
Remove LH mid A-pillar trim

注
1x clip, 2x tabs
Remove LH lower A-pillar trim

注
7x clips
Remove LH footwell cover

注
1x connector, 2x magnets
Move LH front seat backward
Remove LH front floor mat
Remove LH console side carpet

注
11x clips
Fold LH front cabin carpet aside for full access
Remove RH mid A-pillar trim

注
1x clip, 2x tabs
Remove RH lower A-pillar trim

注
7x clips, Partially release seal if needed
Remove RH footwell cover

注
3x magnets, 1x connector, 4x datums
Move RH front seat backward
Remove RH front floor mat
Remove RH console side carpet

注
11x clips
Fold RH front cabin carpet aside for access

注
Caution not to damage styrofoam of carpet
Release harness from RH footrest panel

注
1x clip
Remove RH footrest panel

注
2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
Disconnect brown fakra connection from car computer

注
1x connector, X836
Raise and support vehicle

注
Prepare to raise vehicle, Set air suspension to "Jack Mode", Position lift arm pads on vehicle jack pads
Remove LH front wheel cap

注
Lift every other spoke at a time until cap is released from rim
Loosen LH front wheel

注
5x nuts, 21mm, 175 Nm
Remove RH front wheel cap

注
Lift every other spoke at a time until cap is released from rim
Loosen RH front wheel

注
5x nuts, 21mm, 175 Nm
Raise vehicle partially and lower onto locks

注
Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
Remove LH front wheel

注
5x nuts, 21mm, 175 Nm
Partially release rear portion of LH rear wheel liner

注
5x clips, 1x fan clip, Move liner aside
Disconnect LH front repeater

注
2x connectors
Remove RH front wheel

注
5x nuts, 21mm, 175 Nm
Partially release rear portion of RH rear wheel liner

注
5x clips, 1x fan clip, Move liner aside
Disconnect RH front repeater

注
2x connectors
Release LH grommet from body

注
Use a razor blaze, carefully cut electrical tape away to expose rubber dust boot
Remove electrical tape securing harness bundle to rubber dust boot
Remove the connector from the coax cable

注
Using drag pin tool, Carefully lift down tab and simultaneously pull coax cable away from connector
Apply harness tape onto LH coax overlay cable before installation

注
Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
Position LH coax overlay cable into place, Place through LH wheel liner and dust boot towards interior cabin

注
Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
Pull LH coax overlay cable through bulkhead and into interior cabin

注
Pull harness toward car computer under dashboard
Position LH coax overlay cable onto main dash body harness, Secure cable onto harness using zip ties

注
5x zip-ties, Trim off excess material after harness has been secured
Secure coax overlay through LH wheel liner and frunk harness

注
4x zip-ties, Trim off excess material after harness has been secured
Depin the RH side coax cable (Terminal 1) from the connector X846

注
Verify that you are removing the correct side ( 1 & 2, where 1 is the RH repeater and 2 is the LH repeater. ) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
Insert coax overlay terminal into connector X846
Remove the coax cable from the Connector X846

注
Using the drag pin tool carefully lift the hold down tab an simultaneously pull the coax away from the connector
Insert the connector locking tab and reconnect X846 together
Cut off the vehicle side repeater coax terminal and tape to vehicle harness

注
Cut the coax connector only
Connect LH front repeater

注
2x connectors, Support repeater from exterior to prevent damage to retaining clips
Secure LH grommet onto body

注
Use electrical tape to wrap the end of the dust boot
Secure rear portion of LH rear wheel liner

注
5x clips, 1x fan clip, Secure liner
Install LH front wheel

注
5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
Release RH grommet from body

注
With a razor blade, carefully cut the electrical tape away exposing the rubber dust boot
Remove electrical tape securing harness bundle to rubber dust boot
Remove the connector from the coax cable

注
Using drag pin tool, Carefully lift down tab and simultaneously pull coax cable away from connector
Apply harness tape onto RH coax overlay cable before installation

注
Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
Position RH coax overlay cable into place, Place through RH wheel liner and dust boot towards interior cabin

注
Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
Pull RH coax overlay cable through bulkhead and into interior cabin

注
Pull harness toward car over car computer
Position RH coax overlay cable onto harness, Secure cable onto car computer harness

注
3x zip-ties, Trim off excess material after harness has been secured
Secure coax overlay through RH wheel liner and frunk harness

注
4x zip-ties, Trim off excess material after harness has been secured
Depin the RH side coax cable (Terminal 1) from the connector X846

注
Verify that you are removing the correct side ( 1 & 2, where 1 is the RH repeater and 2 is the LH repeater. ) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
Remove the coax cable from the Connector X846

注
Using the drag pin tool carefully lift the hold down tab an simultaneously pull the coax away from the connector
Insert coax overlay terminal into connector X846
Insert the connector locking tab and reconnect X846 together
Connect brown fakra connection onto car computer

注
1x connector, X836
Cut off the vehicle side repeater coax terminal and tape to vehicle harness

注
Cut the coax connector only
Connect RH front repeater

注
2x connectors, Support repeater from exterior to prevent damage to retaining clips
Secure RH grommet onto body

注
Use electrical tape to wrap the end of the dust boot
Secure rear portion of RH rear wheel liner

注
5x clips, 1x fan clip, Secure liner
Install RH front wheel

注
5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
Lower vehicle until tires are touching ground

注
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Torque LH front wheel

注
5x nuts, 21mm, 175 Nm
Install LH front wheel cap

注
Align valve stem with cap
Torque RH front wheel

注
5x nuts, 21mm, 175 Nm
Install RH front wheel cap

注
Align valve stem with cap
Remove vehicle from lift

注
Lower lift arms fully and remove them from under vehicle, Remove air suspension from "Jack Mode"
Fold LH main carpet back into place
Install LH console side carpet

注
11x clips
Install LH footwell cover

注
1x connector, 2x magnets
Install LH lower A-pillar trim

注
7x clips, Verify weather seal is seated properly
Install LH mid A-pillar trim

注
1x clip, 2x tabs, Verify weather seal is seated properly
Install LH front floor mat
Move LH front seat to original position
Install RH footrest panel

注
2x bolts, 10mm, 5 Nm, 1x nut, 10mm, 5 Nm
Secure harness to RH footrest panel

注
1x clip
Fold RH main carpet back into place

注
Caution not to damage styrofoam of carpet
Install RH console side carpet

注
11x clips
Install RH footwell cover

注
3x magnets, 4x datums, 1x connector
Install RH front floor mat
Install RH lower A-pillar trim

注
7x clips, Verify weather seal is seated properly
Install RH mid A-pillar trim

注
1x clip, 2x tabs, Verify weather seal is seated properly
Move RH front seat to original position
Install the wiper module. See 雨刮器模块（拆卸和更换）.
Unlock the vehicle gateway. See 网关（解锁）.
Reset DAS on UI

注
Select "Driver Assist" > "Cameras" > "Reset DAS", Ensure all cameras and reset DAS icon turn green on UI, If not you need to investigate further why a the particular DAS component is flagging red
运行 ODIN 例行程序 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
Raise both front windows
Close RH front door
Close LH front door

注