2024-04-30
사이드 에어백 - 내측 - 운전석(스포츠 시트)(탈거 및 교체)
교정 코드
200107220.24
참고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.
참고: FRT에 대한 자세한 내용과 FRT가 만들어진 방법은 표준 정비 작업시간을(를) 참조하십시오. FRT 값에 대한 피드백을 제공하려면 LaborTimeFeedback@tesla.com으로 이메일을 보내십시오.
참고: 아래 절차를 수행할 때 적절한 PPE를 착용했는지 확인하려면 개인 보호의 내용을 참조하십시오.
토크 규격
설명 | 토크 값 | 권장 공구 | 재사용/교체 | 참고 |
---|---|---|---|---|
운전석 내측 에어백을 시트 등받이 프레임에 고정하는 너트(2개) |
![]() 5.4 Nm (4.0 lbs-ft) |
|
재사용 |
탈거
- LH 전면 도어를 열고 LH 전면 창문을 내립니다.
- Remove the LH front seat décor assembly. See 장식 패널 - 1열 시트 - LH(스포츠 시트)(탈거 및 교체).
- Remove the LH front seat back panel. See Back Panel - LH (Sport Seat) \(Remove and Replace\).
- Remove the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
- Disconnect LV power. See LV 전원(연결 해제 및 연결).
- Release the connector lock, and then disconnect the driver inboard airbag electrical connector.
-
Remove the nuts (x2) that attach the
driver inboard airbag to the seat back frame, and then remove the airbag from the seat
assembly.
TIp다음 공구 사용을 권장합니다.
- 10mm 딥소켓
- 코드리스 래칫/임팩트 드라이버
- 래칫/토크 렌치
장착
-
Position the driver inboard airbag to
the seat back frame, and then install the nuts (x2) that attach the airbag to the seat
assembly.5.4 Nm (4.0 lbs-ft)경고Only use hand tools to install the fasteners.TIp다음 공구 사용을 권장합니다.
- 10mm 딥소켓
- 코드리스 래칫/임팩트 드라이버
- 래칫/토크 렌치
- Connect the driver inboard airbag electrical connector, and then secure the connector lock.
- Connect LV power. See LV 전원(연결 해제 및 연결).
- Install the rear underhood apron. See 후드 내 에이프런 - 후면(탈거 및 교체).
- Install the LH front seat back panel. See Back Panel - LH (Sport Seat) \(Remove and Replace\).
- Install the LH front seat décor assembly. See 장식 패널 - 1열 시트 - LH(스포츠 시트)(탈거 및 교체).
- Raise the LH front window and close the LH doors.