2026-05-13
支架 - 前端（带加热泵款）（拆卸和更换）
校正代码
10101012
0.96
注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。
注意：请参阅平均维修工时深入了解 FRT 及其创建方式。
注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
注意：请参阅人体工程学注意事项查看安全健康的作业规程。
警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
拆卸
- Open the LH front door and lower the LH front window.
- Remove the underhood storage unit. See 前备箱储物单元（拆卸和更换）.
- Remove the front fascia. See 饰板 - 前（拆卸和安装）.
-
Disconnect the active grille shutter actuator connector.
注Do not push down on the red tab. Pull the red tab to disengage the lock, and then pull it again to release the connector.
-
Remove the ambient temperature sensor cover from the active grille shutter.
-
Disconnect the ambient temperature sensor connector.
-
Disconnect the hood latch open switch.
注Do not push down on the red tab. Pull the red tab to disengage the lock, and then pull it again to release the connector.
-
Disconnect the hood latch actuator.
-
Remove hood latch actuator from front end carrier
注2x bolts, 10mm, 5 Nm
-
Remove hood latch from front end carrier
注2x bolts,10mm, 8 Nm, Mark latch location for alignment when installing
-
Remove LH center fascia reinforcement from front end carrier
注1x tab, 2x datums, Release locking tab under fascia reinforcement, then pull straight up to release fascia reinforcement
-
Remove RH center fascia reinforcement from front end carrier
注1x tab, 2x datums, Release locking tab under fascia reinforcement, then pull straight up to release fascia reinforcement
-
Disconnect front acceleration sensors
注1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector, Disconnect LH, RH, and center front acceleration sensor
-
Remove bolts securing front bumper beam with energy absorber to LH crush can
注2x bolts, 15mm, 75 Nm
-
Remove bolts securing front bumper beam with energy absorber to RH crush can
注2x bolts, 15mm, 75 Nm
-
Remove front bumper beam with energy absorber
注Use a pry bar as needed to remove front bumper beam, Be cautious when prying not to damage body, Slightly tap with dead blow hammer to assist with removal as needed
-
Disconnect LH FEM harness connector
注1x locking connector, Disengage locking tab
-
Disconnect RH FEM harness connector
注1x locking connector, Disengage locking tab
-
Remove radar assembly harness clip from FEM radar bracket
注1x clip
-
Disconnect the radar assembly connector.
-
Remove the FEM radar bracket from front end carrier
注4x bolts, 10mm, 8 Nm
-
Use bungee cords to support the cooling fan module assembly.
-
Remove RH bolt securing cooling fan module assembly to front end carrier
注1x bolt, 8mm, 10 Nm, Recommend assistance to support the cooling fan module assembly
-
Remove LH bolt securing cooling fan module assembly to front end carrier
注1x bolt, 8mm, 10 Nm, Recommend assistance to support the cooling fan module assembly
-
Remove lower bolts securing front end carrier to vehicle
注4x bolts, 13mm, 16 Nm
-
Remove ankle catcher from front end carrier
注2x datums, Slightly pull carrier outward to clear datum from ankle catcher
-
Remove upper bolts securing front end carrier to vehicle and remove front end carrier
注2x bolts, 13mm, 16 Nm
-
Remove FEM harness from front end carrier (5x clips).
安装
-
Install FEM harness to front end carrier (5x clips).
-
Position front end carrier to vehicle and install upper bolts securing front end carrier hand tight
注2x bolts, 13mm, 16 Nm, Torque at later step
-
Position the ankle catcher onto the front end carrier
注2x datums, Slightly pull carrier outward to secure ankle catcher onto datums
-
Install lower bolts securing front end carrier to vehicle
注4x bolts, 13mm, 16 Nm
-
Torque upper bolts securing front end carrier to vehicle
注2x bolts, 13mm, 16 Nm
-
Install bolts securing cooling fan module to front end carrier
注2x bolts, 8mm, 10 Nm
-
Remove bungee cords supporting cooling fan module assembly
注2x bungee cords
-
Install the FEM radar bracket to front end carrier
注4x bolts, 10mm, 8 Nm
-
Connect the radar assembly connector.
-
Install radar assembly harness clip to FEM radar bracket
注1x clip
-
Connect RH FEM harness connector
注1x connector, Engage locking tab
-
Connect LH FEM harness connector
注1x connector, Engage locking tab
-
Position front bumper beam with energy absorber
注Use a dead blow hammer as needed to install front bumper beam into front crush cans
-
Install bolts securing front bumper beam with energy absorber to LH crush can
注2x bolts, 15mm, 75 Nm
-
Install bolts securing front bumper beam with energy absorber to RH crush can
注2x bolts, 15mm, 75 Nm
-
Connect front acceleration sensors
注3x connectors, Engage locking tab, Connect LH, RH, and center front acceleration sensors
-
Install RH center fascia reinforcement to front end carrier
注1x tab, 2x datums, Engage locking tab, Push straight down for installation
-
Install LH center fascia reinforcement to front end carrier
注1x tab, 2x datums, Engage locking tab, Push straight down for installation
-
Install hood latch to front end carrier
注2x bolts,10mm, 8 Nm, Hand tighten bolts and make fine adjustments, Align hood latch with marked locations
-
Install hood latch actuator onto front end carrier
注2x bolts, 10mm, 5 Nm
-
Connect the hood latch actuator.
-
Connect the hood latch open switch connector
注1x connector, Engage locking tab
-
Connect the ambient temperature sensor connector.
-
Install ambient temperature sensor cover into active grille shutter
-
Install connector to active grille shutter actuator
注1x connector , Engage locking tab
- Install the front fascia. See 饰板 - 前（拆卸和安装）.
- Install the underhood storage unit. See 前备箱储物单元（拆卸和更换）.