2026-03-06

Tie Rod Kit - LH (Remove and Replace)

校正代码 32013202 FRT 0.48 注意： 除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。 除非明确要求，否则请勿堆叠校正代码。 注意： 请参阅平均维修工时深入了解 FRT 及其创建方式。 要提供有关 FRT 值的反馈，请发送电子邮件至ServiceManualFeedback@tesla.com。 注意： 请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意： 请参阅人体工程学注意事项查看安全健康的作业规程。

  • 2025-12-16: Released new procedure.

拆卸

  1. Raise and support the vehicle. See 举升车辆 - 双柱举升机
  2. Open LH front door
  3. Lower LH front window
  4. Remove the LH front wheel arch liner. See 轮拱内衬 - 后 - LH（拆卸和更换）
  5. Remove and discard the nut that secures the LH front tie rod end to the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    注
    Use of the following tool(s) is recommended:
    • 22 mm socket
    180 Nm (132.7 lbs-ft)
  6. Remove the LH front tie rod end from the LH front knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Move the rotor back and forth for easier removal.
  7. Remove and discard the large clamp from the bellows.
  8. Remove the seal clip from the bellows.
  9. Slide the bellows toward the LH outer tie rod end to access the ball joint.
  10. Remove the LH tie rod assembly from the pinion housing.
    Informational PurposesAn informational icon, calling your attention
    注
    Use of the following tool(s) is recommended:
    88 Nm (64.9 lbs-ft)

安装

  1. Turn the jam nut on the new tie rod to adjust the length and match the old tie rod before installation.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Count the threads on the removed tie rod, then adjust to the same count on the new one. This will make alignment adjustment easier.
    Informational PurposesAn informational icon, calling your attention
    注
    Use of the following tool(s) is recommended:
    • 21 mm 12pt combination wrench
    • 14 mm 12pt combination wrench
    • Extension
  2. Install the LH inner tie rod assembly onto the pinion housing.
    Informational PurposesAn informational icon, calling your attention
    注
    Use of the following tool(s) is recommended:
    88 Nm (64.9 lbs-ft)
  3. Slide the bellows into the clamping position.
  4. Secure the large bellows clamp onto the bellows.
  5. Secure the bellows seal clip onto the bellows.
  6. Position the LH front tie rod end to the LH front knuckle.
  7. Install a new nyloc nut to secure the LH tie rod end to the LH front knuckle
    Informational PurposesAn informational icon, calling your attention
    注
    Use of the following tool(s) is recommended:
    • 22 mm socket
    180 Nm (132.7 lbs-ft)
  8. Remove the LH front wheel arch liner. See 轮拱内衬 - 后 - LH（拆卸和更换）
  9. Remove the vehicle from the lift. See 举升车辆 - 双柱举升机
  10. Raise the windows and close the doors.
  11. Review the wheel alignment requirements and add correction code as needed. See 定位要求 - 悬架