2025-06-17

Brake Rotor - Rear - LH (Remove and Replace)

校正代码 33010202 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure.

  • 2025-05-08: Updated brake pad burnishing step to be performed after rotor replacement.
  • 2024-05-28: Updated references and cautions.
  • 2023-11-22: Added extra information for single rotor replacement.
  • 2023-10-03: Updated procedure to latest GSD validation: added brake pad burnishing/test drive as a separate activity with correction code 00040100.
  • 1134786-00-A 制动钳扩张器工具,Model 3
Informational PurposesAn informational icon, calling your attention
For detailed brake specifications, see 制动器.
Informational PurposesAn informational icon, calling your attention
If only a single rotor needs replacing (due to damage), the corresponding axle rotor must be measured for runout and thickness. See Brake Rotor - Rear - LH (Measure Runout).

扭矩规格

http://service.tesla.com/user/documents Test
Table 1. Torque Specifications: Brake Rotors - Rear - LH
描述 扭矩值 推荐工具 重复使用/更换 备注
LH rear caliper to the LH rear knuckle
83 Nm (61.2 lbs-ft)
  • 外梅花套筒 E18
  • 棘轮/扭矩扳手
更换
Brake rotor to the hub
5 Nm (3.7 lbs-ft)
  • 10 毫米套筒
  • 2 英寸加长件
  • 棘轮/扭矩扳手
重复使用

拆卸

  1. Raise the vehicle and remove the LH rear wheel. See Wheel Assembly (Remove and Install).
  2. Place the vehicle into EPB Service Mode. See Parking Brake - Caliper - Rear - LH (Release).
  3. Remove and discard the bolts that attach the LH rear caliper to the LH rear knuckle, remove the caliper from the knuckle, and allow the caliper to hang from an S-hook.
    83 Nm (61.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 外梅花套筒 E18
    • 棘轮/扭矩扳手
  4. Use the caliper spreader tool to push the caliper piston to the fully open position.
    Informational PurposesAn informational icon, calling your attention
    Note
    This allows for more clearance when new brake pads are installed.
  5. Remove the bolt that attaches the brake rotor to the hub, and then remove the brake rotor from the hub.
    5 Nm (3.7 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    Note
    Early production vehicles may not be equipped with a bolt that attaches the brake rotor to the hub.
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米套筒
    • 2 英寸加长件
    • 棘轮/扭矩扳手

安装

安装程序与拆卸程序相反,以下各项除外:

  1. Replace all patchbolts.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    To prevent damage to the flexible brake hose, make sure that the brake hose is not twisted and can bend forward and does not make contact with the wheel arch liner when the vehicle is lowered.
  2. Put the vehicle into Park to exit EPB Service Mode and engage the parking brake.
  3. Press the brake pedal at least 5 times to seat the pads against the rotor.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Always check that the brake pads are seated correctly before driving the vehicle.
  4. Burnish the brakes. See Brake Pads - Burnishing.
    Informational PurposesAn informational icon, calling your attention
    Note
    During vehicle driving, make sure that proper brake pedal feel and performance is achieved.
    Informational PurposesAn informational icon, calling your attention
    Note
    Add the correction code for brake pad burnishing 33013000 as a separate activity to the Service Visit.