2024-06-25

Filter - Cabin (Remove and Replace)

校正代码 18100102 0.18 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure.

  • 2024 年 6 月 6 日：为软件版本为 2024.14+ 的车辆添加了驾驶室滤清器健康分数重置。
  • 2024 年 4 月 9 日：更新了程序，以适应带顶部和底部螺钉的驾驶室滤清器盖板。

拆卸

图 1. 带顶部螺钉的驾驶室滤清器盖板的动态展示
  1. 关闭温度控制系统。
  2. 拆卸中控台右侧面板处地毯。请参阅Side Panel - Center Console - LH (Remove and Replace)。
  3. 使用卡子工具拆下锁片；将右侧脚部空间总成从仪表板上松开。
  4. 检查驾驶室滤清器盖板固定到 HVAC 单元的方式。
  5. 如果驾驶室滤清器盖板用锁片固定：松开驾驶室滤清器盖板底部的锁片，然后将盖板移至一旁。
  6. 如果驾驶室滤清器盖板用顶部螺钉固定：拆卸副驾位脚部空间盖板。请参阅Cover - Footwell - Passenger (LHD) (Remove and Replace)。
  7. 如果驾驶室滤清器盖板用顶部螺钉或底部螺钉固定：拆卸将驾驶室滤清器盖板固定到 HVAC 单元的螺钉，然后将驾驶室滤清器盖板移至一旁。
    Informational PurposesAn informational icon, calling your attention
    注
    在带加热泵款车型上，该螺钉位于驾驶室滤清器盖板的底部
  8. 将滤清器锁片向外折叠，然后将上部滤清器从滤清器外壳中拉出。
  9. 拆卸上部滤清器，然后将下部滤清器向上提起并从滤清器外壳中拉出。

安装

  1. 将下部滤清器安装到滤清器外壳中，注意使箭头指向车辆后部。
  2. 将上部滤清器安装到滤清器外壳中，注意使箭头指向车辆后部，然后将滤清器锁片向内折叠。
  3. 如果驾驶室滤清器盖板用顶部螺钉或底部螺钉固定：将驾驶室滤清器盖板安装到 HVAC 单元上，然后安装将驾驶室滤清器盖板固定到 HVAC 单元的螺钉。
    1.2 Nm (.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    注
    紧固盖板前，先接合下部盖板锁片。
  4. 如果驾驶室滤清器盖板用顶部螺钉固定：安装副驾位脚部空间盖板。请参阅Cover - Footwell - Passenger (LHD) (Remove and Replace)。
  5. 如果驾驶室滤清器盖板用锁片固定：将驾驶室滤清器盖板上部锁片安装到 HVAC 单元卡槽中，然后安装驾驶室滤清器盖板下部锁片。
  6. 安装中控台右侧面板处地毯。请参阅Side Panel - Center Console - LH (Remove and Replace)。
  7. Check whether the vehicle cabin filter health score requires reset: On the vehicle touchscreen, touch Controls (vehicle icon) > Software, and then scroll down to display the vehicle software version.
    • If the vehicle software version is older than 2024.14, the cabin filter health score does not need to be reset. Skip to the next step in this procedure.
    • If the vehicle software version is 2024.14 or newer:
      1. Enable Service Mode. See Service Mode.
      2. For Model 3 with PTC heater: In the Service Mode menu, touch Thermal (snowflake icon), and in the "Air Filter Diagnostics" section, touch Reset Filter Health. The cabin filter health score is now reset for PTC heater Model 3. Skip to the next step in this procedure.
      3. For Model 3 with Heat Pump: In the Service Mode menu, touch Thermal (snowflake icon) > HVAC > Right, and then touch Cabin Filter > Reset Cabin Filter Score.
      4. The cabin filter health score is now reset. Continue to the next step in this procedure.
    图 2. Reset cabin filter health score for PTC heater Model 3
    图 3. Reset cabin filter health score for Heat Pump Model 3—Model Y shown; Model 3 similar