2024-06-25

充电端口(中国)(母排类型)(拆卸和更换) ((拆卸和更换))

校正代码 44012712 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure.

  • 2024 年 2 月 2 日:更新了盖板图片。
  • 2023 年 10 月 27 日:将充电接口至车身螺栓扭矩更新至 9 Nm。
  • 2023 年 7 月 6 日:在拆卸部分的第 12、14、15 步和安装部分的第 9 步添加了视频。
  • 2024 年 4 月 2 日:变更步骤,将“拆卸后备箱左侧饰板”变更为“松开部分卡子并将饰板移至一旁”。
  • 1076928-00-A Hioki 9461
  • 1130480-00-A 超薄测试探针,Fluke TP38
Warning IconA warning icon, calling your attention to a possibly risky situation
警告

Only technicians who have been trained in High Voltage Awareness and have completed all required certification courses (if applicable) are permitted to perform this procedure. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

Warning IconA warning icon, calling your attention to a possibly risky situation
警告

Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.

Warning IconA warning icon, calling your attention to a possibly risky situation
警告

If corrective eyewear is necessary to safely perform any procedure, make sure that the eyewear is securely restrained to the head and cannot fall off.

Warning IconA warning icon, calling your attention to a possibly risky situation
警告

执行此程序时需要穿戴适当的个人防护装备 (PPE):

  • 高压 (HV) 绝缘手套
  • 皮革手套保护罩
  • 高压绝缘手套测试器
  • 护目镜
  • 电气绝缘保护安全鞋
Warning IconA warning icon, calling your attention to a possibly risky situation
警告

手套充气机是测试高压绝缘手套的唯一推荐方式。开始此程序前,需确认两只高压绝缘手套均通过测试。如果任何一只手套未通过充气检测,则需弃置这副手套。

Warning IconA warning icon, calling your attention to a possibly risky situation
警告

确保高压绝缘手套未过期。高压绝缘手套有效期为印在手套上的测试日期后 12 个月内,但首次使用后,即使手套仍处于上述 12 个月有效期内,也只能使用 6 个月。

扭矩规格

表 1. 扭矩规格充电端口(中国)(母排类型)(拆卸和更换) ((拆卸和更换))
描述 扭矩值 推荐工具 重复使用/更换 备注
将充电接口母排引线固定到充电接口总成的螺母(2 个)
9 Nm (6.6 lbs-ft)
  • 10 毫米深套筒
  • 回旋头棘轮/回旋头扭矩扳手
重复使用
将充电接口总成固定到车辆的螺栓(3 个)
9 Nm (6.6 lbs-ft)
  • 10 毫米深套筒
  • 回旋头棘轮/回旋头扭矩扳手
重复使用

拆卸

  1. 打开所有四个车门,降下所有四个车窗。
  2. 打开后备箱。
  3. 打开充电接口盖板。
  4. 断开 12V/低压电源。请参阅12V/LV Power (Disconnect and Connect)
  5. 执行充电接口电压检查程序。请参阅Charge Port Voltage Check
  6. 拆卸后备箱饰板。请参阅Garnish - Trunk (Remove and Replace)
  7. 拆卸后备箱门槛饰板。请参阅Trim - Sill - Trunk (Remove and Replace)
  8. 断开电气连接器与地面照明灯的连接。
  9. 松开后备箱地毯的边缘,然后将后备箱左侧饰板移至一旁。将地毯压入饰板下,注意请勿造成过多褶皱。
  10. 松开锁片,然后断开电气连接器与充电接口总成的连接。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    图 1. 图示为 Model 3;Model Y 与之类似
  11. 拆卸白色锁片,然后断开直流逻辑连接器与充电接口的连接。
    图 2. 图示为 Model 3;Model Y 与之类似
  12. 拆卸白色锁片,然后断开交流逻辑连接器与充电接口的连接。
    图 3. 图示为 Model 3;Model Y 与之类似
  13. 将锁片向上推动,然后将三相连接器从充电接口上断开。
    图 4. 图示为 Model 3;Model Y 与之类似
  14. 使用长凿轻轻松开将安全盖固定到母排支架的锁片(2 个),然后拆下安全盖。
    Informational PurposesAn informational icon, calling your attention
    撬动时请勿用力过猛,以免损坏安全盖。
  15. 检查并佩戴高压绝缘手套和皮革手套。
  16. 拆卸将充电接口母排引线固定到充电接口总成的螺母(2 个)。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米深套筒
    • 回旋头棘轮/回旋头扭矩扳手
  17. 脱下高压绝缘手套和皮革手套。
  18. 将充电接口手动释放缆索从车身上松开。
  19. 拆卸将充电接口固定到车辆的螺栓(3 个),然后将充电接口从车辆上拆下。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米深套筒
    • 回旋头棘轮/回旋头扭矩扳手

安装

  1. 对 Hioki 电阻表执行零点调节,以便稍后在此程序中测量电阻。请参阅Resistance Meter (Zero Adjust)
  2. 如果将重新安装同一充电接口:使用异丙醇 (IPA) 湿巾清洁充电接口总成后部的充电接口母排高压接头,然后等待风干 1 分钟。
    Informational PurposesAn informational icon, calling your attention
    如果将安装新的充电接口总成,请跳过这一步骤,因为新的充电接口已预先涂抹了导电膏。
    Informational PurposesAn informational icon, calling your attention
    TIp
    使用塑料饰板工具,将异丙醇 (IPA) 湿巾推入充电接口母排高压接头的缝隙中。
  3. 将充电接口放置到车辆上,然后安装将充电接口固定到车辆的螺栓(3 个)。
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米深套筒
    • 回旋头棘轮/回旋头扭矩扳手
  4. 将充电接口手动释放缆索接线管固定到车身的卡子上。
  5. 检查并佩戴高压绝缘手套和皮革手套。
  6. 使用异丙醇 (IPA) 湿巾清洁充电接口母排引线上的残留物和碎屑,然后等待风干 1 分钟。
    图 5. 母排支架设计可能不同
  7. 如果将重新安装同一充电接口:在各充电接口母排引线(2 个)与充电接口接触的一侧涂抹两滴导电膏。
    Informational PurposesAn informational icon, calling your attention
    如果将安装新的充电接口总成,请跳过这一步骤,因为新的充电接口已预先涂抹了导电膏。
    Informational PurposesAn informational icon, calling your attention
    确保接触表面涂满导电膏。
    图 6. 母排支架设计可能不同
  8. 安装将母排引线固定到充电接口的螺母(2 个)。
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米深套筒
    • 回旋头棘轮/回旋头扭矩扳手
  9. 在充电接口处,使用 Hioki 电阻计测量充电接口母排引线与充电接口母排螺柱之间的电阻。另请对其他引线和螺柱执行该测试。
    Informational PurposesAn informational icon, calling your attention
    可接受的电阻值为 0.050 毫欧(50 微欧)至 0.325 毫欧(325 微欧)。如果测得电阻值高于 0.325 毫欧(325 微欧),说明高压接头电阻过大。拆卸紧固件,使用异丙醇清洁接触区域,重新安装紧固件,再次测试(视情况而定)。
    Informational PurposesAn informational icon, calling your attention
    如果电阻值低于 0.050 毫欧(50 微欧),请重新放置探针并再次测量。如果尝试 4 次后电阻值始终低于 0.050 毫欧(50 微欧),则说明测试通过;请继续执行下一步骤。
  10. 脱下高压绝缘手套和皮革手套。
  11. 安装母排支架上的安全盖,确保两个锁片接合。
  12. 连接充电接口上的三相连接器,然后向下滑动锁片。
    图 7. 图示为 Model 3;Model Y 与之类似
  13. 连接充电接口上的交流逻辑连接器,然后安装白色锁片。
    v
    图 8. 图示为 Model 3;Model Y 与之类似
  14. 连接充电接口上的直流逻辑连接器,然后安装白色锁片。
    图 9. 图示为 Model 3;Model Y 与之类似
  15. 将电气连接器连接到充电接口传动装置,然后接合锁片。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    Push the red locking tab towards the connector to engage the locking mechanism. DO NOT push down or pull up on the red locking tab.
  16. 将后备箱左侧饰板移回原位,然后将卡子固定到车身。
  17. 将电气连接器连接到地面照明灯。
  18. 安装后备箱门槛饰板。请参阅Trim - Sill - Trunk (Remove and Replace)
  19. 安装后备箱饰板。请参阅Garnish - Trunk (Remove and Replace)
  20. 重新连接 12V 电源。请参阅12V/LV Power (Disconnect and Connect)
  21. 升起所有车窗,关闭所有车门。