2020-12-16

Paint Protection Film - Rocker Panels (Retrofit)

校正代码 12052006 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure.

程序

图 1. 动画演示

在安装车漆保护膜套件之前查看以下注意事项,以免过早磨损或剥落:

Warning IconA warning icon, calling your attention to a possibly risky situation
警告
在干燥温暖的地方安装车漆保护膜套件。安装之后,至少 24 小时内不能洗车并避免淋雨。
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
LH 和 RH 保护膜不可互换;粘性背衬应粘贴在车漆上,与车身轮廓贴合。
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
切勿让薄膜的任意部位伸出车辆边缘。不要将薄膜粘贴在门槛板和围板之间的车身线条上(双向折弯)。
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
确保用刮板刮除薄膜下的所有气泡。
  1. 用汽车洗洁精和水清洁安装区域,然后用干净的超细纤维毛巾将水擦干。确保清洗掉所有污垢、油脂等。
  2. 在喷瓶或其他适用的容器中混合约 85% 的水和 15% 的婴儿洗发水来调配滑液。摇晃容器,确保将溶液彻底摇匀。
  3. 在安装区域以及 LH 下部和 LH 上部薄膜上喷洒适量的滑液。
  4. 从背衬上撕下 LH 下部薄膜,然后往上面喷洒滑液。
  5. 将 LH 下部薄膜粘贴到门槛板上,从而将标签底部与门槛板底部对齐,标签后端与车辆的后围板对齐。
    Informational PurposesAn informational icon, calling your attention
    根据需要喷洒滑液以便移动薄膜,使其与车身轮廓对齐,并将整张薄膜都粘贴到漆面上。
  6. 正确粘贴薄膜之后,用刮板刮除薄膜与漆面之间的所有气泡。
  7. 从背衬上撕下 LH 上部薄膜,然后往上面喷洒滑液。
  8. 将 LH 上部薄膜粘贴到围板上,从而将标签底部与 LH 下部标签的顶部对齐,标签后部与车辆后围板对齐。
    Informational PurposesAn informational icon, calling your attention
    根据需要喷洒滑液以便移动薄膜,使其与车身轮廓对齐,并将整张薄膜都粘贴到漆面上。
  9. 正确粘贴薄膜之后,用刮板刮除薄膜与漆面之间的所有气泡。
  10. 对 RH 侧执行第 3-9 步。