校正代码 31031812 0.48 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至ServiceManualFeedback@tesla.com。 注意：请参阅 人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

1. Remove the LH rear wheel. See 轮毂总成（拆卸和安装）
2. Inspect LH Rear Upper Knuckle Ball Joint for red markings.
   注

   If the red markings are present on opposite sides (180 degrees), do not replace the Knuckle Ball Joint. The Knuckle Ball Joint is a 1 time replaceable part.

   

   

3. Release LH rear upper aft link from knuckle
   注

   1x bolt, 1x nut, 21mm, 134 Nm

   

4. Remove the Rear Upper Knuckle Ball joint using revision 2130203-00-A of the CABJ Bushings R&R Tool Kit M3/MY.
   注

   Go to the next step when using revision 2130203-00-B.
   1. Install knuckle ball joint replacement tool on LH Rear Upper Knuckle Ball Joint for removal
      注

      Utilize the combination of cups for removal, A - Bushings Receiver, B - Bushings Pusher, C - Remove Washer M3, Ensure cups sit flush to ball joint and knuckle surface, A to C has a key, Install A with recess to corner of the knuckle, Ball joint will only press out towards rear of vehicle, Apply lubricant to threaded rod if dry

      

      

      

      

   2. Press out LH Rear Upper Knuckle Ball Joint
      警告

      Do not use an impact tool or other power tool on the ball joint replacement tool. To prevent damage to the ball joint replacement tool, only use hand tools.

      注

      Ball joint should press out with minimal resistance, If met with high resistance inspect for misalignment of tool cups, Utilize windows in receiving cup to monitor progress

      

      

   3. Remove Rear Upper Knuckle Ball Joint from knuckle ball joint replacement tool

      

      

   4. Go to step 6.
5. Remove the Rear Upper Knuckle Ball joint using revision 2130203-00-B of the CABJ Bushings R&R Tool Kit M3/MY.
   1. Remove 1 nut from threaded rod
      注

      Remove the nut and separate from the bearing

      

      

   2. Install knuckle ball joint replacement tool on LH Rear Upper Knuckle Ball Joint for removal
      注

      Install the nut on the receiver cup , Utilize the combination of cups for removal, M3 Bushings Receiver, B - Bushings Pusher, Ensure cups sit flush to ball joint and knuckle surface, And the arrow is aligned with mark on knuckle , Install M3 receiver cup with recess to corner of the knuckle, Ball joint will only press out towards rear of vehicle, Apply lubricant to threaded rod if dry

      

      

   3. Press out LH Rear Upper Knuckle Ball Joint
      注

      Ball joint should press out with minimal resistance, If met with high resistance inspect for misalignment of tool cups, Utilize windows in receiving cup to monitor progress

      

      

   4. Remove Rear Upper Knuckle Ball Joint from knuckle ball joint
      注

      Loosen the nut and remove the receiver cup, then pull the ball joint out of the knuckle

      

6. Put on protection gloves
7. Clean LH Rear knuckle
   注

   Clean surface area where Rear Upper Knuckle Ball Joint is installed into the knuckle from any debris and oxidation, allow 1 minute dry time

   

8. Degrease LH Rear Upper Knuckle Ball Joint
   注

   Clean contact area of Rear Upper Knuckle Ball Joint and allow 1 minute dry time

   

9. Apply Loctite on LH Rear Upper Knuckle Ball Joint
   注

   Use the region specific Loctite. For EMEA: Loctite 638. For North America: Loctite 680

   注

   Take care not to apply loctite on the rubber seals

   警告

   Allow 30 minutes curing time for Loctite. Continue this procedure, but do not drive the vehicle during the 30 minute curing time.

   

   

10. Position new LH Rear Upper Knuckle Ball Joint to knuckle
    注

    Ensure ball joint is sitting concentric to the bore, installation is performed from the rear side of the knuckle and ball joint has only 1 orientation of the installation, discard Nitrile Gloves

    

    

    

11. Install the Rear Upper Knuckle Ball joint using revision 2130203-00-A of the CABJ Bushings R&R Tool Kit M3/MY.
    注

    Go to the next step when using revision 2130203-00-B.
    1. Install knuckle ball joint replacement tool on LH Rear Upper Knuckle Ball Joint for Install
       注

       Utilize the combination of cups for Install, A - Bushings Receiver, B - Bushings Pusher, D - Install Washer M3 Ensure cups sit flush to ball joint and knuckle surface, A to D has a key, Install A with the recess aligned with the top line of the knuckle

       

       

       

    2. Press LH Rear Upper Knuckle Ball Joint in
       警告

       Do not use an impact tool or other power tool on the ball joint replacement tool. To prevent damage to the ball joint replacement tool, only use hand tools.

       注

       Ball joint could be pressed in with some resistance, If met with extreme high resistance inspect for misalignment of tool cups, Utilize notch in installation cup to monitor progress, When nearing end of bore the installation cup may need to be re-aligned to meet machined surface, Verify full installation

       

       

       

    3. Remove knuckle ball joint replacement tool from LH Rear Upper Knuckle Ball Joint

       

       

    4. Go to step 13.
12. Install the Rear Upper Knuckle Ball joint using revision 2130203-00-B of the CABJ Bushings R&R Tool Kit M3/MY.
    1. Install knuckle ball joint replacement tool on LH Rear Upper Knuckle Ball Joint for Install
       注

       Remove the nut from M3 receive cup and install on B - pushing cup , Utilize the combination of cups for Install, M3-LH Bushings Receiver, B - Bushings Pusher, Ensure cups sit flush to ball joint and knuckle surface, And the arrow is aligned with mark on Knuckle , Ball joint will only press in towards front of vehicle

       

       

    2. Press LH Rear Upper Knuckle Ball Joint in
       警告

       Do not use an impact tool or other power tool on the ball joint replacement tool. To prevent damage to the ball joint replacement tool, only use hand tools.

       注

       Ball joint could be pressed in with some resistance, If met with extreme high resistance inspect for misalignment of tool cups, Utilize notch in installation cup to monitor progress, When nearing end of bore the installation cup may need to be re-aligned to meet machined surface, Verify full installation

       

       

    3. Remove knuckle ball joint replacement tool from LH Rear Upper Knuckle Ball Joint
13. Clean any excessive Loctite from LH Rear Upper Knuckle
    注

    Allow 1 minute dry time

    

    

14. Mark the LH Rear Upper Knuckle Ball Joint with red paint pen.
    注

    Machined surface should be near flush with ball joint. Markings must be on opposite sides (180 degrees).

    

15. Position LH rear upper aft link to knuckle
    注

    1x bolt, 1x nut, 21mm, 134 Nm, Torque at later step

    

16. Torque bolt securing LH rear upper aft link to knuckle
    注

    1x bolt, 21mm, 134 Nm, Mark with paint pen

    

17. Install the LH rear wheel. See 轮毂总成（拆卸和安装）
18. 请参阅“定位要求”表，以确定是否需要 EPAS 定位检查 (EC) 或四轮定位检查 (AC)。如果已执行，请将定位检查/调整校正代码作为一项单独的工项添加到服务工单。请参阅 定位要求 - 悬架。