2024-09-09

Light - Side Repeater - Front - LH (Remove and Replace)

校正代码 17403002 0.12 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure.

  • 2023 年 12 月 12 日：更新了例行程序。
图 1. 图示为 Model 3；Model Y 与之类似
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

拆卸

Warning IconA warning icon, calling your attention to a possibly risky situation
警告
Whenever a camera has been moved out of its original position (for example, a camera or windshield replacement), camera calibration data must be cleared using the vehicle touchscreen: Controls > Service > Camera Calibration > Clear Calibration.
  1. 打开左前车门，降下左前车窗。
  2. 使用触摸屏启用“维护模式”。请参阅Service Mode。
  3. 在位于左前侧转向灯周围的左前翼子板上粘贴保护胶带。
  4. 松开将左前侧转向灯固定到左前翼子板的转向灯底部卡子（2 个），然后将转向灯从翼子板上分离。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    如果将重新安装同一侧中继器，注意请勿损坏安装锁片。
    Informational PurposesAn informational icon, calling your attention
    注
    小心地将侧中继器向上撬起，然后再撬动底部，将其从翼子板上松开。卡子数量可能有所不同。
  5. 断开电气线束与左前侧转向灯连接器（2 个）的连接，然后将转向灯从车辆上拆下。

安装

  1. 将电气线束连接到左前侧转向灯连接器（2 个）。
  2. 将左前侧转向灯牢固安装到左前翼子板上，然后紧固将转向灯固定到翼子板的卡子。
    Warning IconA warning icon, calling your attention to a possibly risky situation
    警告
    如果将重新安装同一侧中继器，请确保安装锁片和卡子未损坏。如果有任何锁片或卡子损坏，请更换中继器。
    Informational PurposesAn informational icon, calling your attention
    注
    卡子数量可能有所不同。
  3. 揭下粘贴在左前侧转向灯周围左前翼子板上的保护胶带。
  4. 在触摸屏上，点击Vehicle Info > Driver Assist > Cameras > Reset DAS，然后根据提示运行例行程序。
  5. 退出“维护模式”。请参阅Service Mode。
  6. 升起左前车窗，关闭左前车门。
  7. 告知客户，现在需要手动驾驶，以使摄像头进行自校准。
    Informational PurposesAn informational icon, calling your attention
    注
    Self-calibration can take up to 100 miles (160 km) of manual driving, depending upon the road type and condition. Until self-calibration is complete, the message "Autopilot Features Currently Unavailable: Manual Driving Required While Camera Is Calibrating" is displayed if an attempt is made to engage an Autopilot feature.