2024-04-08

Cooling System (Partial Refill and Bleed)

校正代码 18300000 0.60 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure.

程序

  1. 将装有 Toolbox 3 的笔记本电脑与车辆相连。
  2. 向搜索字段中输入“thermal”。
    Informational PurposesAn informational icon, calling your attention
    如果尚未选择“Actions”,请确保选择该项。
  3. 点击PROC_VCFRONT_X_THERMAL-FILL-DRAINvia Toolbox: (link)旁边的 “play” 按钮,然后选择 “Run”。
  4. 取下超级/冷却液瓶的盖。
    图 1. 配备超级瓶的 Model 3(非加热泵款);为清晰起见,已拆下其他组件
    图 2. 配备冷却液瓶的 Model Y;Model 3(加热泵款)与之类似。为清晰起见,已拆下其他组件
  5. 超级/冷却液瓶中添加冷却液,使液位处于 MAX 线处(加热泵款车辆)或高出 MAX 线约 6 毫米(非加热泵款车辆)
  6. 向搜索字段中输入“vcfront”。
  7. 点击TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    旁边的 “play” 按钮,然后选择 “Run”。
    Informational PurposesAn informational icon, calling your attention
    确保驱动导轨处于关闭状态。打开驱动导轨将停止例程。
    Informational PurposesAn informational icon, calling your attention
    例程运行时,监测超级/冷却液瓶,根据需要添加冷却液,使液位保持在 NOM 与 MAX 之间。
    Informational PurposesAn informational icon, calling your attention
    测试持续约 10 分钟。
    Informational PurposesAn informational icon, calling your attention
    可在“PT Thermal”选项卡下查看的测试速度将在 3,500 至 6,500 RPM 之间变化。
    Informational PurposesAn informational icon, calling your attention
    如果速度悬停在 7,000 RPM 左右,则再次执行此程序。
  8. 仅限加热泵款车辆:空气净化例程完成后,检查冷却液瓶液位并添加冷却液至 MAX 线处。
  9. 仅限非加热泵车:空气净化例程完成后,检查超级瓶液位,然后添加冷却液至液位高出 MAX 线约 6 毫米(0.25 英寸)。
  10. 安装超级/冷却液瓶的盖。

安装

安装程序与拆卸程序相反。