2026-05-28

Trim Cover - 40 Seatback - 2nd Row (7-Seat) (Remove and Replace)

교정 코드 13080300402 FRT 0.36 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2026-05-04: Released new procedure.

탈거

  1. Move the RH front seat forward.
    Informational PurposesAn informational icon, calling your attention
    참고
    Adjust the seatback if needed to avoid contacting the headliner.
  2. Fold the 2nd row 40 seatback down.
    Informational PurposesAn informational icon, calling your attention
    참고
    Via seat switch or manual tether.
  3. Move the 40 seat forward using the towel bar.
  4. Remove the 2nd row 40 seatback panel.
    Informational PurposesAn informational icon, calling your attention
    참고
    9x clips, 2 hooks. Lift up at the top left corner of the 40 back panel to release the clips, and then slide it forward to release the hooks.
  5. Remove the RH shoulder switch from the 40 seat assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, 1x connector. Use a plastic trim tool to pry the top of the switch away from the 40 seat assembly to ease removal.
  6. Remove the 40 seat toe kick cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    6x clips.
  7. Remove the 40 seat harness from the bottom side of the seat frame.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, 1x connector. Remove the elastic harness holder to release the harness.
  8. Remove the headrest from the 2nd row 40 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Simultaneously depress the guide button and insert a 90 degree pick into the guide opening. Lift up while engaged.
  9. Remove the headrest guides from the 2nd row 40 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Pull back on the lower portion of the headrest guide to release the tab while also applying upward force to remove the headrest guides.
  10. Remove the 2nd row 40 seatback assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips. Release the clips that attach the 40 seatback and lift it upwards. The seat belt will be removed in a later step.
  11. Put the 2nd row 40 seatback assembly on a suitable working surface.
  12. Disconnect the 40 seat heating connector.
  13. Release the 2nd row 40 seatback cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    16x tabs. Pull material downward to release it.
  14. Remove the backrest shell from the 2nd row 40 seatback cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    Early production models may have staples that hold the material to the shell in some areas.
  15. Remove the 40 seatback cover from the foam.
    Informational PurposesAn informational icon, calling your attention
    참고
    3x hogring. Hook & loop attachment around perimeter. Cut the hogrings, clean debris. Note: If 40/60 seat that is not being repaired does not have ISOFIX flag for child seats, the seat covers will also require replacement.

장착

  1. Install the 40 seatback cover to the foam.
    Informational PurposesAn informational icon, calling your attention
    참고
    3x hogrings. Small tie wraps may be used as a substitute. If used, trim flush and rotate the tie wraps head away from the visible surface. Hook & loop around the perimeter.
  2. Install the 2nd row 40 seatback cover to the backrest shell.
    Informational PurposesAn informational icon, calling your attention
    참고
    16x hooks. Pull the material downward to attach, make sure that the material is distributed evenly on the visible side.
  3. Connect the 40 seat heating pad connector.
  4. Install the LH seatback onto the 40 seat assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    9x clips, 4 hooks. Attach hooks onto the frame rail. Work upwards and fasten all the clips.
  5. Install the headrest guides into the 40 seat assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    Install the headrest guides by pressing them downwards until the lower tab is seated.
  6. Install the headrest onto the 40 seat assembly.
  7. Install the harness onto the bottom of the seat frame.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, 1x connector. Install elastic harness retainers.
  8. Install the 40 seat toe kick cover.
    Informational PurposesAn informational icon, calling your attention
    참고
    6x clips.
  9. Install the RH shoulder switch to the 40 seat assembly.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x clips, 1x connector.
  10. Install the 40 backpanel onto the seatback.
    Informational PurposesAn informational icon, calling your attention
    참고
    9x clips. Install the back panel clips to the seatback frame starting at the lower back panel, working your way up towards the upper back panel.
  11. Move the 2nd row 40 seatback to the vertical position.
    Informational PurposesAn informational icon, calling your attention
    참고
    Via seat switch or manual tether. Remove seatback protection if applicable.
  12. Move the RH front seat to the original position.