2026-06-12

Ball Joint - Rear - Upper - Rear Knuckle - LH (Remove and Replace)

교정 코드 31031852 FRT 0.60 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2026-05-29: Released new procedure.

토크 규격

표 1. 토크 규격 Ball Joint - Rear - Upper - Rear Knuckle - LH (Remove and Replace)
설명 토크 값 권장 공구 재사용/교체 참고
후면 상단 후방 링크를 너클에 고정하는 볼트 및 너트
134 Nm (98.8 lbs-ft)
  • 21mm 딥소켓
 재사용
후면 브레이크 캘리퍼를 너클에 고정하는 볼트(2개)
83 Nm (61.2 lbs-ft)
  • 코드리스 래칫/임팩트 드라이버
  • 3인치 익스텐션
  • 외부 Torx E18
  • 래칫/토크 렌치
 교체 볼트: 1188643-00-C

탈거

  1. Use the touchscreen to release the parking brake. See Parking Brake - Caliper - Rear - LH (Release) (Maintenance).
  2. Remove the LH rear wheel. See 휠 어셈블리(탈거 및 장착)
  3. Inspect the rear upper knuckle ball Joint for red markings. If two red markings are present on opposite sides, discontinue this procedure and replace the knuckle assembly. See Rear Knuckle - LH (Remove and Replace).
    Informational PurposesAn informational icon, calling your attention
    참고
    The Knuckle Ball Joint is a 1 time replaceable part. If the red markings are present on opposite sides (180 degrees), the Knuckle Ball Joint has been replaced before. Disregard any other markings on the knuckle and/or ball joint.
  4. Partially release the bolts that attach the LH rear brake caliper bracket to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Loosen the lower bolt and remove the upper bolt, and then move the upper side of the caliper. Bolts must be discarded before installation.
  5. Remove the bolt and nut that attach the rear upper aft link to the knuckle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 21mm 딥소켓
  6. Remove the nut from the threaded rod of the knuckle ball joint replacement tool, and then remove the bearing.
  7. Use the vehicle specific combination of cups for removal: B (pusher) and M3 (receiver), and then install the nut on the M3 (receiver) cup.
  8. Install the B (pusher) cup onto the nut and bearing on the threaded rod of the knuckle ball joint replacement tool, and then insert the tool into the ball joint towards the rear of the vehicle.
  9. Install the M3 (receiver) cup onto the threaded rod of the knuckle ball joint replacement tool, and then hand tighten the nuts to align the triangles on both cups with the cast marking on the knuckle.
  10. Tighten the nut on the side of the B (pusher) cup to press out the knuckle ball joint.
    Informational PurposesAn informational icon, calling your attention
    참고
    The ball joint should press out into the M3 (receiver) cup with minimal resistance. If met with high resistance, ensure the cups are properly aligned. Use the opening in the receiver cup to monitor the progress.
  11. Loosen the nut from the M3 (receiver) cup, and then remove the cup and the ball joint from the knuckle.

장착

  1. Put on protective gloves.
  2. Clean the inner surface area of the knuckle where the ball joint is installed with IPA wipes, and then allow 1 minute to dry.
  3. Degrease and clean the contact area of the new ball joint with IPA wipes, and then allow 1 minute to dry.
  4. Apply Loctite on the new ball joint.
    Informational PurposesAn informational icon, calling your attention
    참고
    Use the region specific Loctite. For EMEA: Loctite 638. For North America: Loctite 680.
    Informational PurposesAn informational icon, calling your attention
    참고
    Take care not to apply Loctite on the rubber seals
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Allow 30 minutes curing time for Loctite. Continue this procedure, but do not drive the vehicle during the 30 minute curing time.
  5. Position the new ball joint onto the rear side of the knuckle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure the ball joint is positioned concentric to the bore. The ball joint has only 1 installation orientation.
  6. Install the M3 LH cup onto the nut and bearing on the threaded rod of the knuckle ball joint replacement tool, and then insert the tool into the ball joint towards the rear of the vehicle.
  7. Install the B cup onto the threaded rod of the knuckle ball joint replacement tool, and then hand tighten the nuts to align the triangles on both cups with the cast marking on the knuckle.
  8. Tighten the nut on the side of the M3 LH cup to press the knuckle ball joint into the knuckle.
  9. Loosen the nut on the B (pusher) cup, and then remove the knuckle ball joint replacement tool from the knuckle.
  10. Clean any excessive Loctite from the knuckle with IPA wipes, and then allow 1 minute to dry.
  11. Mark the new ball joint and the knuckle with a red paint pen on two sides, to indicate the ball joint has been replaced and this procedure must not be performed at a later stage..
    Informational PurposesAn informational icon, calling your attention
    참고
    Markings must be on opposite sides (180 degrees).
  12. Position the rear upper aft link to the knuckle, and then torque the bolt and nut that attach the rear upper aft link to the knuckle.
    134 Nm (98.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    다음 공구를 사용하는 것이 좋습니다.
    • 21mm 딥소켓
  13. Install new bolts (x2) that attach the LH rear brake caliper bracket to the knuckle.
    83 Nm (61.2 lbs-ft)
    다음 공구를 사용하는 것이 좋습니다.
    • 코드리스 래칫/임팩트 드라이버
    • 3인치 익스텐션
    • 외부 Torx E18
    • 래칫/토크 렌치
  14. Install the LH rear wheel. See 휠 어셈블리(탈거 및 장착)
  15. Press and hold the brake pedal and select Park on the touchscreen to disable EPB Service Mode.
  16. Exit Service Mode.