2026-09-03

Tire Rotation (Mobile Only)

교정 코드 34020105 FRT 0.48 메모: 절차에서 명시적으로 언급하지 않는 한 교정 코드 및 해당 관련 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호을(를) 참조하여 적절한 PPE를 착용했는지 확인하십시오. 메모: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2026-08-27: Released new procedure.
참고
이 절차는 전후륜 휠 크기가 같고 비방향성 타이어 장착 차량에 적용됩니다. 크기가 다른 휠 또는 방향성 타이어의 교환 지침은 아래를 참조하십시오.
  • 전후륜 휠 크기가 다르며 비방향성 타이어를 장착한 경우: 전방 타이어를 교체하려면 차량 LH 전면과 RH 전면을 잭으로 들어 올리고, 후방타이어를 교체하려면 차량 LH 후면과 RH 후면을 잭으로 들어 올립니다.
  • 전후륜 휠 크기가 같고 방향성 타이어를 장착한 경우: LH 타이어를 교체하려면 차량 LH 전면 및 LH 후면을 잭으로 들어 올리고, RH 타이어를 교체하려면 차량 RH 전면과 RH 후면을 잭으로 들어 올립니다.

Vehicle ride quality and handling are maximized when all 4 tires are the same age, model, and tread depth. Rotating tires regularly allows them to wear at the same rate and increases the service life. Tesla recommends tire rotation every 6,250 miles (10,000 km) or if tread depth difference is 2/32 in (1.5mm) or greater, whichever comes first.

참고
Tesla recommends replacing tires in pairs unless the other tires are within 2/32 in (1.5 mm) of tread depth of the new tire.
참고
If only 2 new tires are installed, the new tires must be installed on the rear of the vehicle. In wet conditions, the tires that have less tread have less traction than the new tires. Reduced traction at the front of the vehicle leads to understeer, which most drivers are better able to react to than the oversteer that would result if the worn tires were on the rear of the vehicle.
참고
Tesla recommends replacing a tire if any of the tread depths are 4/32 in (3 mm) or less.
참고
Model Y is pictured, but this procedure can be performed on .

절차

  1. Ensure the vehicle is parked on a level surface.
  2. Install wheel chocks on the RH front wheel.
  3. Remove the LH rear wheel cap, if equipped. See Cover - Wheel - Front - LH (Remove and Replace).
  4. Loosen LH rear wheel lug nuts (x5)
    참고
    5x nuts, 21mm, 175 Nm
    경고
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  5. Remove the LH front wheel cap. See Cover - Wheel - Front - LH (Remove and Replace).
  6. Loosen LH front wheel lug nuts (x5).
    참고
    5x nuts, 21mm, 175 Nm
    경고
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  7. Jack up the LH rear of the vehicle.
    참고
    Position the jack stand adapter onto the floor jack, position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
    참고
    Raise the vehicle until the LH front wheel is off the ground.
  8. Position jack stands underneath the LH front and LH rear of the vehicle.
    경고
    전기 잭이나 공압 잭을 사용하는 경우 부상 방지를 위해 차량을 들어올리기 전에 차량에서 멀리 떨어져 있으십시오.
    참고
    Align the jack stand cutout with the floor jack.
    참고
    Align the top opening of the jack stand with the bottom of the jack stand adapter.
  9. Slowly lower the floor jacks, making sure the LH front and rear jack stands are aligned with the jack stand adapters.
    참고
    Perform a shake test to verify stability.
  10. Remove the lug nuts from the wheel, and then remove the LH rear wheel from the vehicle.
    참고
    5x nuts, 21mm, 175 Nm
  11. Remove the lug nuts from the wheel, and then remove the LH front wheel from the vehicle.
    참고
    5x nuts, 21mm, 175 Nm
  12. Swap the LH rear wheel with the LH front wheel and install the LH wheels.
    참고
    2x wheels, 10x nuts, 21mm. Install the lug nuts by hand first and then use power tools; torque them in a later step.
    경고
    Wear appropriate personal protective equipment (PPE) when performing this procedure to prevent personal injury.
  13. Raise the vehicle off the LH rear and LH front jack stands.
    참고
    Jack up the LH rear of the vehicle until the LH front wheel is off the jack stand.
  14. Remove the LH front and LH rear jack stands (x2), and then lower the vehicle.
  15. Remove the chocks from the RH front wheel.
  16. Install wheel chocks on the LH front wheel.
  17. Remove the RH rear wheel cap. See Cover - Wheel - Front - LH (Remove and Replace).
  18. Loosen RH rear wheel lug nuts (x5).
    참고
    5x nuts, 21mm, 175 Nm
    경고
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  19. Remove the RH front wheel cap. See Cover - Wheel - Front - LH (Remove and Replace).
  20. Loosen RH front wheel lug nuts (x5).
    참고
    5x nuts, 21mm, 175 Nm
    경고
    Use only hand tools to break the lug nuts loose. Power tools should only be used to remove the lug nuts after they have been loosened.
  21. Jack up the RH rear of the vehicle.
    참고
    Position the jack stand adapter onto the floor jack, position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
    참고
    Raise the vehicle until the RH front wheel is off the ground.
  22. Position jack stands underneath the RH front and RH rear of the vehicle.
    경고
    전기 잭이나 공압 잭을 사용하는 경우 부상 방지를 위해 차량을 들어올리기 전에 차량에서 멀리 떨어져 있으십시오.
    참고
    Align the jack stand cutout with the floor jack.
    참고
    Align the top opening of the jack stand with the bottom of the jack stand adapter.
  23. Slowly lower the floor jacks, making sure the RH front and rear jack stands are aligned with the jack stand adapters.
    참고
    Perform a shake test to verify stability.
  24. Remove the lug nuts from the wheel, and then remove the RH rear wheel from the vehicle.
    참고
    5x nuts, 21mm, 175 Nm
  25. Remove the lug nuts from the wheel, and then remove the RH front wheel from the vehicle.
    참고
    5x nuts, 21mm, 175 Nm
  26. Swap the RH rear wheel with the RH front wheel and install the RH wheels.
    참고
    2x wheels, 10x nuts, 21mm. Install the lug nuts by hand first and then use power tools; torque them in a later step.
    경고
    Wear appropriate personal protective equipment (PPE) when performing this procedure to prevent personal injury.
  27. Raise the vehicle off the RH rear and RH front jack stands.
    참고
    Jack up the RH rear of the vehicle until the RH front wheel is off the jack stand.
  28. Remove the RH front jack stand, and then lower the vehicle.
  29. Jack up the LH rear of the vehicle.
    참고
    Position the jack stand adapter onto the floor jack, position the floor jack under the vehicle lift point, and then carefully raise the floor jack, aligning the jack stand adapter locating pin with the hole at the vehicle lift point.
  30. Slowly lower the floor jack, making sure the LH rear jack stand is aligned with the jack stand adapter.
    참고
    Perform a shake test to verify stability.
  31. Remove the lug nuts from the wheel, and then remove the LH rear wheel from the vehicle.
    참고
    5x nuts, 21mm, 175 Nm
  32. Remove the lug nuts from the wheel, and then remove the RH rear wheel from the vehicle.
    참고
    5x nuts, 21mm, 175 Nm
  33. Swap the RH rear wheel with the LH rear wheel and install the rear wheels.
    참고
    2x wheels, 10x nuts, 21mm. Install the lug nuts by hand first and then use power tools; torque them in a later step.
    경고
    Wear appropriate personal protective equipment (PPE) when performing this procedure to prevent personal injury.
  34. Remove the LH rear jack stand, and then lower the vehicle.
  35. Remove the RH rear jack stand and then lower the vehicle.
  36. Torque all 4 rear wheels.
    참고
    5x nuts, 21mm, 175 Nm
  37. Install all 4 wheel caps. See Cover - Wheel - Front - LH (Remove and Replace).
  38. Remove the chocks from the LH front wheel.
  39. Open the LH front door.
  40. Unlock vehicle gateway. See 게이트웨이(잠금 해제).
  41. Tap Controls > Chassis > Alignment & Tire > Reset Learned Tire Values, and click Run.
    참고
    Click Close once the routine is completed.
  42. Tap Controls > Service > Wheel & Tire > Tires, choose the tire season and click Reset. After resetting, check if the Tire Service Mileage in the upper right corner is displayed as Less than 500 km ago.
  43. Exit Service Mode.
  44. Close the LH Front door.
  45. Inform the customers that a short calibration drive cycle might be required.