2026-08-09

Chiller (V2) (Remove and Replace)

교정 코드 18260100502 FRT 1.08 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Informational PurposesAn informational icon, calling your attention
참고
이 절차에서는 A/C 냉매(회수 및 재충전) 절차가 수행되어야 합니다. 서비스 방문에 자동으로 추가되지 않은 경우 서비스 방문에 교정 코드 18200102를 동일한 활동에 별도 교정 항목으로 추가합니다.

토크 규격

표 1. 토크 규격: Chiller (V2) (Remove and Replace)
설명 토크 값 권장 공구 재사용/교체 참고
슈퍼매니폴드-컴프레서 A/C 라인을 슈퍼매니폴드에 고정하는 볼트
22 Nm (16.2 lbs-ft)
  • 13mm 소켓
 재사용
슈퍼매니폴드 하네스 브래킷을 슈퍼매니폴드에 고정하는 볼트(3개)
8 Nm (5.9 lbs-ft)
  • 8mm 딥소켓
 재사용
칠러-슈퍼매니폴드를 고정하는 너트(4개)
6.3 Nm (4.6 lbs-ft)
  • 8mm 딥소켓
 재사용

탈거

  1. Set up the AC machine.
  2. Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
  3. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_VCFRONT_X_START-THERMAL-FILL-DRAINvia Service Mode:
    • Thermal ➜ Actions ➜ Start Thermal Fill/Drain
    • Thermal ➜ Coolant System ➜ Start Coolant Fill/Drain
    • Thermal ➜ Refrigerant System ➜ Start Refrigerant Fill/Drain
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Start Fluid Fill/Drain
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Start Fluid Fill/Drain
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Start Coolant Fill/Drain
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Start Coolant Fill/Drain
    via Toolbox:(link)
  4. Power off the vehicle from the center display.
    Informational PurposesAn informational icon, calling your attention
    참고
    On the touchscreen, touch Controls > Safety > Power Off > Power Off.
  5. Remove the HEPA filter assembly. See HEPA Filter Assembly (Remove and Replace).
  6. Remove the underhood storage unit. See 후드 내 보관 유닛(탈거 및 교체).
  7. Remove the air intake duct. See Duct - Air Intake (Remove and Replace).
  8. Remove the front aero shield. See Aero Shield - Front (Remove and Replace).
  9. A/C 냉매를 회수합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge) (Restore).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    다음 단계를 수행하기 전에 A/C 시스템에 과압이 없는지 확인하십시오. 그렇지 않으면 구성품 손상 및/또는 상해를 입을 수 있습니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    HFO-R1234yf 및 R134a는 위험 물질로 취급되며 잘못 다룰 경우 심각한 상해를 일으킬 수 있습니다. 에어컨 시스템을 대상으로 작업 수행 시 안면 보호, 보안경, 안면 보호대, 내열 장갑, 내화학성 장갑, 고무 부츠 및 에이프런 또는 전신 방수복 등 적합한 개인 보호 장비를 착용해야 합니다.
  10. Remove A/C machine hoses from the vehicle.
  11. 슈레이더 밸브(2개)를 조심스럽게 눌러 A/C 시스템 압력과 실제 주변 대기압 사이의 압력 차이가 없도록 맞춥니다.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    슈레더 밸브를 모두 눌러야 합니다. 그렇지 않을 경우 상해를 입을 수도 있습니다.
  12. Remove the frunk reinforcement beam. See 빔 - 보강재 - 프렁크(탈거 및 교체).
    Informational PurposesAn informational icon, calling your attention
    참고
    It is not necessary to separate the isolation brackets from the frunk reinforcement beam.
  13. Position a fluid catcher underneath front of the vehicle.
  14. Remove the coolant bottle cap.
  15. Release the spring clip, disconnect the radiator inlet hose from the supermanifold, and then plug the hose and supermanifold.
  16. Release the spring clip, disconnect the radiator outlet hose from the supermanifold, and then plug the hose and supermanifold.
  17. Release the spring clip, disconnect the front drive unit return hose from the supermanifold, and then plug the hose and supermanifold.
  18. Remove the bolt that attaches the supermanifold-to-compressor A/C line to the supermanifold.
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 공구를 사용하는 것이 좋습니다.
    • 13mm 소켓
  19. Remove the supermanifold-to-compressor A/C line from the supermanifold, and move it aside.
    Informational PurposesAn informational icon, calling your attention
    참고
    Carefully position the line so that oil does not drip out.
  20. Disconnect the pressure and temperature sensor connectors (x3).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    빨간색 잠금 탭을 누르지 마십시오. 커넥터가 잠금 해제될 때까지 커넥터에서 탭을 당겨 뺀 다음 커넥터의 메인 몸체를 계속 당겨 완전히 연결 해제합니다.
  21. Remove the bolts (x3) that attach the supermanifold harness bracket to the supermanifold.
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 공구를 사용하는 것이 좋습니다.
    • 8mm 딥소켓
  22. Grip the bottom of the coils, and pull the supermanifold harness bracket and the valve coils evenly outward to disengage them from the supermanifold.
  23. Remove the seals from the coils, and then install them to the expansion valve cores.
    Informational PurposesAn informational icon, calling your attention
    참고
    This is to aid valve coil installation.
  24. Remove the nuts (x4) that attach the chiller to the supermanifold.
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 공구를 사용하는 것이 좋습니다.
    • 8mm 딥소켓
  25. Slightly release the RH side of the chiller from supermanifold and allow excess coolant to drain, and then remove the chiller from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Leave the AC ports of LCCR intact to supermanifold to avoid any cross contamination.
  26. Remove and discard the chiller gasket from supermanifold.

장착

  1. Install a new chiller gasket into supermanifold.
  2. Lubricate both O-rings on the chiller with the appropriate A/C oil. See for A/C oil specifications.
  3. Hand-tighten the bolts (x4) that attach the cooled condenser to Supermanifold.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure the LCCR is fully seated on Supermanifold before installing the bolts.
  4. Install the nuts (x4) that attach the chiller to the supermanifold.
    6.3 Nm (4.6 lbs-ft)
    • 8mm 딥소켓
  5. Install the supermanifold harness bracket and the valve coils to the supermanifold.
  6. Connect the pressure and temperature sensor connectors (x3).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    빨간색 잠금 탭을 커넥터를 향해 밀어 잠금 장치를 체결합니다. 빨간색 잠금 탭을 누르거나 당기지 마십시오.
  7. Install the bolts (x3) that attach the supermanifold harness bracket to the supermanifold.
    8 Nm (5.9 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 공구를 사용하는 것이 좋습니다.
    • 8mm 딥소켓
  8. Install new seal washers on the supermanifold side of the supermanifold-to-compressor A/C line, and then lubricate the washers with a small amount of the appropriate A/C oil. See 유액 및 용량 for A/C oil specifications.
  9. Position the supermanifold to compressor A/C line onto the supermanifold, and then hand-tighten the bolt that attaches the A/C line to the supermanifold.
  10. Tighten the bolt that attaches the supermanifold to compressor A/C line to the supermanifold.
    22 Nm (16.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    참고
    다음 공구를 사용하는 것이 좋습니다.
    • 13mm 소켓
  11. Remove the plugs, immediately connect the front drive unit powertrain return hose to the supermanifold, and then fasten the clip.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull test to verify that the hose is fully seated.
  12. Remove the plugs from the supermanifold and radiator outlet hose, immediately connect the radiator outlet hose to the supermanifold, and then fasten the clip.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  13. Remove the plugs from the supermanifold and radiator inlet hose, immediately connect the radiator inlet hose to the supermanifold, and then fasten the clip.
    Informational PurposesAn informational icon, calling your attention
    참고
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  14. Install the frunk reinforcement beam, See 빔 - 보강재 - 프렁크(탈거 및 교체).
  15. 진공 누출 테스트 및 오일 주입을 수행하고 A/C 냉매를 재충전합니다. 참조 항목: A/C Refrigerant (Recovery and Recharge) (Restore).
  16. Perform a cooling system vacuum refill. See Cooling System - Vacuum Refill (Test/Adjust).
  17. Remove the fluid catcher from underneath the front of the vehicle.
  18. Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
  19. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_VCFRONT_X_STOP-THERMAL-FILL-DRAINvia Service Mode:
    • Thermal ➜ Actions ➜ Stop Thermal Fill/Drain
    • Thermal ➜ Coolant System ➜ Stop Coolant Fill/Drain
    • Thermal ➜ Refrigerant System ➜ Stop Refrigerant Fill/Drain
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Stop Coolant Fill/Drain
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Stop Coolant Fill/Drain
    via Toolbox:(link)
  20. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): ODIN 루틴 실행 TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    via Toolbox:(link)
  21. Install the front aero shield. See Aero Shield - Front (Remove and Replace).
  22. Install the underhood storage unit. See 후드 내 보관 유닛(탈거 및 교체).
  23. Inspect the coolant level and top off as necessary, and then install the coolant bottle cap.
    Informational PurposesAn informational icon, calling your attention
    참고
    Ensure that the coolant level is at the "Max" line. Vacuum fill required if greater than 1L lost during repair。
  24. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): TEST-SELF_VCFRONT_X_HEAT-PUMP-COMMISSIONINGvia Service Mode:Thermal ➜ Refrigerant System ➜ Commission Heat Pumpvia Service Mode Plus:Drive Inverter ➜ Front Drive Inverter Replacement ➜ Heatpump commissioningvia Toolbox:(link)
  25. Exit Service Mode. See 정비 모드.
  26. Remove the air intake duct. See Duct - Air Intake (Remove and Replace).
  27. Install the HEPA filter assembly. See HEPA And Carbon Filters (Remove and Replace).
  28. Install the underhood storage unit. See 후드 내 보관 유닛(탈거 및 교체).