교정 코드 40202000 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. Raise and support the vehicle. See 차량 상승 - 2-포스트 리프트.
2. Open LH front door

   

3. Lower LH front window

   

4. ODIN 루틴 실행
5. Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
6. Access thermal system routines via UI
   참고

   Select Service mode > Thermal

   

   

7. Perform "Start Thermal Fill/Drain (Coolant Only)" through Service UI
   참고

   Select Thermal > Coolant System > Coolant Fill/Drain, click Run, close once routine is completed, Thermal Fill Drain routine has a 5 hour time limit, After 5 hours routine must be performed again

   

   

   

8. Disconnect LV power. See GUID-5CD6AB0E-A270-4D28-BAE9-6004D0EE59CD.html.
9. Remove the front aero shield. See GUID-1FF2298A-36EA-482F-9DD7-AA78B48F7753.html.
10. Remove clips secure LH wheel liner to front fascia and valance
    참고

    3x push clips

    

11. Remove clips secure RH wheel liner to front fascia and valance
    참고

    3x push clips

    

12. Remove both side bolts securing valance to fascia
    참고

    2x bolts, T40, 2.5Nm

    

    

13. Secure RH front wheel liner aside
    참고

    1x bungee strap, Secure to subframe

    

14. Position coolant drain container underneath RH front of HV battery

    

15. Attach hose extension to coolant drain hose for extra length

    

16. Attach the powertrain (PT) flush fitting adapter to coolant cart pressure hose

    

17. Disconnect PT return hose
    참고

    1x spring clip, Plug coolant connections as needed, Loss of coolant greater than 1L requires coolant vacuum fill

    

    

18. Attach PT drain fitting adapter to male PT return hose

    

    

    

19. Disconnect PT supply hose
    참고

    1x spring clip, Plug coolant connections as needed, Loss of coolant greater than 1L requires coolant vacuum fill

    

    

20. Attach PT flush fitting adapter to female side of PT supply hose
    참고

    1x spring clip, Perform push-pull test to verify adapter is fully engaged

    

    

    

21. Attach PT drain fitting adapter to coolant pressure tester cart
    참고

    The regulator valve is pre-set to 20 psi, When valve is set to horizontal position it is fully closed, Verify valve is in closed position

    

22. Attach compressed air line to coolant pressure tester
    참고

    Verify valve is in closed position

    

23. Open valve on PT drain fitting adapter
    참고

    When valve is in the vertical position it is fully open

    

24. Slowly open valve on pressure regulator and allow coolant to drain out of PT return hose
    참고

    Open valve very slowly, If opened too quickly, pressure relief valve on superbottle cap may open, Also superbottle cap may make humming noise, If so, pressure is too high and should be lowered by adjusting the valve

    

25. Close valve on pressure regulator
    참고

    Turn valve knob horizontal when coolant is no longer visibly draining

    

26. Remove PT flush fitting adapter from female side of PT supply hose
    참고

    1x spring clip

    

27. Remove plugs then connect PT supply hose
    참고

    1x clips, 1x plugs, Perform push-pull-push test to make sure hose is fully engaged. Loss of coolant greater than 1L requires coolant vacuum fill

    

    

28. Disconnect PT flush fitting adapter from female side of PT return tube
    참고

    1x spring clip

    

29. Remove PT drain fitting adapter from male side of PT return hose
    참고

    1x spring clip, Plug the PT return hose

    

30. Remove plugs then connect PT return tube
    참고

    밀고 당기기 연결 검사를 수행하여 호스가 완전히 안착되었는지 확인하십시오. 호스 연결부를 흔들지 마십시오.

    

    

31. Remove PT drain fitting adapter from cart drain hose

    

32. Remove coolant drain container from underneath vehicle

    

33. Release RH front wheel liner
    참고

    1x bungee strap, Remove bungee strap as needed

    

34. Install bolt securing RH front wheel liner to skid plate
    참고

    1x bolt, 10mm, 5 Nm

    

35. Install clip securing RH wheel liner to body
    참고

    1x push clip

    

36. Install the front aero shield. See GUID-1FF2298A-36EA-482F-9DD7-AA78B48F7753.html.
37. Perform a coolant vacuum refill. See GUID-87DA124C-74A5-4012-B7EA-DAFC1EFACF1A.html.
38. Connect LV power. See GUID-5CD6AB0E-A270-4D28-BAE9-6004D0EE59CD.html.
39. Access thermal system routines via UI
    참고

    Select Service mode > Thermal

    

    

40. Unlock the vehicle gateway. See 게이트웨이(잠금 해제).
41. ODIN 루틴 실행
    참고

    For non China Model Y L vehicles, run "PROC_VCFRONT2_X_STOP-THERMAL-FILL-DRAIN".
42. ODIN 루틴 실행
    참고

    For non China Model Y L vehicles, run "TEST_VCFRONT2_X_THERMAL-COOLANT-AIR-PURGE-START".
43. Inspect coolant level and top off as necessary
    참고

    Ensure that fluid level is at Max line, Vacuum fill required if greater than 1L lost during repair

    

44. Install coolant bottle cap

    

45. ODIN 루틴 실행
46. Install HEPA filter assembly
    참고

    2x bolts, 10mm, 10 Nm, Pivot forward edge down past frunk assembly, Then carefully move rear edge past brake reservoir and into position, Gently press on RH side of filter to seat seal onto duct

    

    

    

    

47. Install rear apron
    참고

    16x trim clips, 3x locator pins, 2x clips, Replace any missing or damaged clips, Ensure pyrotechnic hood actuators are aligned with openings in apron

    

    

    

48. Close hood

    

    

49. Raise LH front window

    

50. Close LH front door