2026-04-30

ECU - Charge Port (7-Seat) (Remove and Replace)

교정 코드 TBD FRT 0.54 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오.참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

탈거

  1. Open all four doors and lower all windows.
  2. Open the hood via the touchscreen.
  3. Move the 1st row LH and RH seats forward.
    Informational PurposesAn informational icon, calling your attention
    참고
    Adjust the seat back to avoid contact with the headliner if needed.
  4. Open the liftgate.
  5. Press the shoulder switch and push the 2nd row seats forward to position the seats into the easy entry mode.
  6. Power off the vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    참고
    On the touchscreen, touch Controls > Safety > Power Off > Power Off.
  7. Remove the HEPA filter. See GUID-9991557E-7CF5-459A-82EF-66D002CDE0C7.html.
  8. Remove the 3rd row seat cushion. See GUID-AAEB9010-2647-442E-B1EC-9C1A025D8250.html.
  9. Press the front switch at the LH trunk trim panel to release the 3rd row LH seat backrest.
  10. Press the rear switch at the LH trunk trim panel to release the 3rd row RH seat backrest.
  11. Disconnect the LV power. See GUID-5CD6AB0E-A270-4D28-BAE9-6004D0EE59CD.html.
  12. Remove the rear load floor.
  13. Remove the LH lower C-pillar trim. See GUID-68DD2EB2-3EAB-4F2E-9BD3-3ADA6B92CAA3.html.
  14. Remove the LH trunk pocket bracket. See 포켓 브래킷 - LH(7인승)(탈거 및 교체).
  15. Release the remaining clips, and then remove the LH 7s trunk side trim.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clip, 2x clip tabs, 4x Guide tabs
  16. Release the LH trunk side trim and disconnect the 12V outlet connector.
    Informational PurposesAn informational icon, calling your attention
    참고
    4x clips, 7x tabs, 1x connector
  17. Disconnect the charge port ECU connectors (x3).
  18. Remove the bolt that attaches the charge port ECU to the vehicle, and then slide the charge port ECU to the right, and then remove the charge port ECU from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    10mm

장착

  1. Install the charge port ECU by sliding it into the slots (x2) of the vehicle body, and then install the bolt that attaches the charge port ECU to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    10mm, 9 Nm
  2. Connect the charge port ECU connectors (x3).
  3. Position the LH trunk side trim and install the lower clips.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x push clips, 5x clips,
    Informational PurposesAn informational icon, calling your attention
    참고
    Start by tucking the lower portion of the trunk side trim around the edge of the 3rd row LH backrest so it slides in and seats properly. Guide the front clip stanchions around the LH C-pillar.
  4. Install the LH trunk side trim.
    Informational PurposesAn informational icon, calling your attention
    참고
    7x tabs, 4x clips, 1x location pin, 1x connector
    Informational PurposesAn informational icon, calling your attention
    참고
    Make sure the trunk seal is properly seated against the edge of the trim.
  5. Install the LH trunk pocket bracket. See 포켓 브래킷 - LH(7인승)(탈거 및 교체).
  6. Connect the LV power. See GUID-5CD6AB0E-A270-4D28-BAE9-6004D0EE59CD.html.
  7. Install the 3rd row seat cushion. See GUID-AAEB9010-2647-442E-B1EC-9C1A025D8250.html.
  8. Move the 1st row and 2nd row seats back to their original positions.
  9. Install the LH lower C-pillar trim. See GUID-68DD2EB2-3EAB-4F2E-9BD3-3ADA6B92CAA3.html.
  10. Raise the 3rd row RH seat backrest to its original position.
    Informational PurposesAn informational icon, calling your attention
    참고
    Manually raise the backrest up to its original position until it locks into place.
  11. Raise the 3rd row LH seat backrest to its original position.
    Informational PurposesAn informational icon, calling your attention
    참고
    Manually raise the backrest up to its original position until it locks into place.
  12. Install the rear load floor.
  13. Close the liftgate.
  14. Reinstall the vehicle firmware. See 소프트웨어 재설치 - 터치스크린.
  15. Raise all windows and close all doors.