2026-03-17

Body Harness - RH (Model Y L) (RHD) (Remove and Install)

교정 코드 NEW 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning

이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.

2026-03-02: Released new procedure.

Open all four doors
Lower all four windows
Open hood
Open liftgate
ODIN 루틴 실행 PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox:(link)
ODIN 루틴 실행
Access chassis system routines using UI

Note
Select Chassis > Brakes
ODIN 루틴 실행
PROC_EPB_X_SERVICE-MODE
via Service Mode:
Chassis ➜ Brakes ➜ EPB Service Mode
Chassis ➜ Brakes ➜ EPB Service Mode
via Service Mode Plus:Drive Unit ➜ Rear Drive Unit Replacement ➜ Release / Re-Engage Emergency Parking Brakevia Toolbox:(link)
Set wheel chocks

Note
Warning: After this action, tire wedges will be set to prevent the vehicle from rolling freely
Partially release RH front primary door seal

Note
For remove RH IP end cap, RH lower A pillar trim, RH front B pillar trim
Remove RH IP end cap

Note
5x clips, 2x guide tabs
Remove RH lower A pillar trim

Note
1x push clip, 7x clips, 4x guide tabs, Pull rear of lower A-pillar upward to release clips then pull rearward to release front tabs and metal clip
Move RH front seat forward

Note
Adjust seatback if needed to avoid contacting headliner
Release seat belt retractor from RH front seat pre tensioner

Note
Insert seat belt release tool in bottom of retractor to release
Remove RH front seat rear bolts

Note
2x patch bolts, TP45, 33.5 Nm, Discard patch bolts after removal
Move RH front seat backward
Remove RH front seat front bolts

Note
2x patch bolts, TP45, 33.5 Nm, Discard patch bolts after removal
Adjust position of RH front seat for easy removal

Note
Move seat to middle of track at most upright position with seat fully up off floor
Move RH 2nd row seat backward

Note
Adjust seat back if needed to avoid contacting other parts
Remove front bolts securing RH 2nd row seat

Note
2x patch bolts, TP45, 33.5 Nm, Discard after removal
Move RH 2nd row seat forward

Note
Adjust seat back if needed
Remove rear bolts securing RH 2nd row seat

Note
2x patch bolts, TP45, 33.5 Nm, Discard after removal
Adjust position of RH 2nd row seat for easy removal

Note
For the convenience remove from vehicle
Power off vehicle from center display

Note
Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
Remove rear apron

Note
16x trim clips, 3x datums, 2x clips
Remove HEPA filter assembly

Note
2x bolts, 10mm, 10 Nm, Pivot rear edge up past brake reservoir then lift up to clear frunk assembly
Disconnect LV battery and first responder loop

Note
2x connectors, Ensure that one minute has passed after window movement before performing the power-off, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge
Disconnect RH front seat harness connector from RH body controller

Note
1x connector, Release lock then remove
Release RH front seat harness

Note
2x clips, 2x guide hook
Pull RH front seat harness from under RH front cabin carpet
Remove RH front seat from vehicle

Note
Recommend assistance, With assistant supporting seatback from 2nd row seat, Remove seat from front RH door opening, Caution not to damage any trim, Protect the seat upholstery when the seat is outside of the vehicle
Disconnect RH 2nd row seat connector

Note
1x connector, 1x clip, Partily lift seat assembly, Release red locking tab and then press white tab to disconnect connector
Remove RH 2nd row seat from vehicle

Note
Recommend assistance, Caution not to damage any trim, Protect the seat upholstery when the seat is outside of the vehicle
Remove trunk load floor from vehicle
Remove trunk sill trim from vehicle

Note
4x clips, 2x loaction pins
Remove LH load floor bracket from vehicle

Note
5x clips, 2x location pins
Remove RH load floor bracket from vehicle

Note
5x clips, 2x location pins
Remove trunk tub from vehicle

Note
2x push clips, 2x location holes
Remove 3rd row seat cushion

Note
2x clips, 1x connector, 2x circular hooks, Press tabs backward then pull front edge up, Press rear seat cushion and lift the front seat cushion
Release clip securing 3rd row LH seat frame harness to seat cushion bolster

Note
1x clip
Remove 3rd row LH seat cushion bolster

Note
1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide LH seat cushion bolster towards front of vehicle to remove
Release clip securing 3rd row RH seat frame harness to seat cushion bolster

Note
1x clip
Remove 3rd row RH seat cushion bolster

Note
1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide RH seat cushion bolster towards front of vehicle to remove
Disconnect 3rd row LH seat frame harness connector

Note
1x connector
Remove bolt securing 3rd row LH front bracket outboard tobody

Note
1x bolt, 11mm, 37 Nm, Discard bolt after removal
Disconnect 3rd row RH seat frame harness connector

Note
1x connector
Remove bolt securing 3rd row RH front bracket outboard to body

Note
1x bolt, 11mm, 37 Nm, Discard bolt after removal
Remove outer bolts securing 3rd row seatbelt and seat back

Note
2x bolts, 11mm, 37 Nm, Discard bolts after removal
Remove inner bolts securing 3rd row seatback complete to body

Note
2x bolts, 11mm, 37 Nm, Discard bolts after removal
Remove 3rd row seatback complete from vehicle

Note
2x location pins, First lift up, Then move the entire body backward, Remove 3rd row seatback complete through the liftgate, Recommended assistant assistance
Partially release RH rear primary door seal from body

Note
For remove RH lower C pillar trim, RH trunk side trim, RH upper C pillar trim.
Remove RH lower C pillar trim from body

Note
7x clips, 1x guide tab, Pull the trim upward to release all clips
Remove RH trunk pocket bracket

Note
2x clips
Release RH trunk side trim clips from body

Note
14x clips, 2x location pins, 2x gudie tabs, Release the RH trunk side trim clips to facilitate the removal of the C pillar upper trim
Disconnect RH 3rd row seat switch connector

Note
1x connector
Remove RH trunk side trim assembly from vehicle

Note
1x clip
Release RH upper C pillar trim clips from body then move aside

Note
10x clips, 4x location pins, 3x guide tabs
Remove RH 3rd row duct B section from vehicle

Note
1x edge clip, 2x tabs
Remove RH lower B pillar trim from body

Note
2x location pins, 8x clips, 1x push clip, Release top side clips. Pull upper then lower half trim inward to release all clips.
Remove RH upper B pillar trim assembly from body then move aside

Note
5x clips, 2x location pins, Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips.
Release RH B pillar lower air duct from body

Note
1x edge clip
Remove double-sided tape underneath RH B-pillar applique
Release RH upper B-pillar applique

Note
1x clip, Insert the clip molding remover tool into the position 7.5cm below the right B-pillar camera, Ensuring that the tool is located under the B-pillar trim seal
Release RH lower B-pillar applique

Note
1x clip, 1x location pin, Insert the clip molding removal tool into the bottom of the right B-pillar, facing upwards by 6cm position, Ensure tool is below B-pillar applique seal
Slide RH B-pillar applique down

Note
1x guide tab, Slide B-pillar applique down slightly to release assembly from body, Camera harness is connected, do not fully remove applique
Release RH applique seal and remove from body

Note
1x trim clip, Slide clip prytool underneath clip to disengage from body, Clip is glued to seal, if prytool is engaged at seal clip will tear away
Disconnect RH B-pillar applique connectors

Note
2x connectors, Disengage locking tab
Clean residual adhesive from RH B-pillar and clean surface with IPA wipe

Note
Allow 1 minute for IPA to dry
Clean residual adhesive from RH B-pillar applique
Release front RH cabin carpet cover from driver footwell hush panel

Note
2x magnets, 2x datums
Remove driver footwell hush panel

Note
1x connector, 7x tabs, 2x location pins
Remove console RH front side panel

Note
15x clips, 3x locating pins, Use trim tool starting at top edge to release upper clips, Pull bottom to release remaining clips, Use caution and pull panel straight away from console
ODIN 루틴 실행
Partially remove LH front primary door seal near LH lower A pillar
Remove LH IP end cap

Note
5x clips, 2x guide tabs
Remove LH upper A pillar trim

Note
5x clips, 2x guide tabs, 1x location pin, 1x tether, Pull inside of the upper portion of upper A pillar, Depress 2x tabs to remove tether from body side, Then pull upper A pillar upward to remove, Tether may very on revision
Remove LH sun visor bracket cover

Note
4x clips, Extending the sun visor may allow for extra working room
Remove LH sun visor from headliner

Note
1x screw, T25, 3.5 Nm, 1x connector, Fold sun visor to the closed and folded down position but do not latch in place
Remove RH upper A pillar trim

Note
5x clips, 2x guide tabs, 1x location pin, 1x tether, Pull inside of the upper portion of upper A pillar, Depress 2x tabs to remove tether from body side, Then pull upper A pillar upward to remove
Remove RH sun visor bracket cover

Note
4x clips, Extending the sun visor may allow for extra working room
Remove RH sun visor from headliner

Note
1x screw, T25, 3.5 Nm, 1x connector, Fold sun visor to the closed and folded down position but do not latch in place
Partially release front end of headliner

Note
5x clips, 1x location pin, Disengage the headliner from the vehicle,Take care not to bend the headliner, Replace any damaged clips
Disconnect interior endpoint connector

Note
1x connector, Disengage locking tab
Disconnect interior radar connector

Note
1x connector, Disengage locking tab, then release connector
Release front windshield harness from A - pillar area

Note
4x clips
Release RH body harness clips from front head area

Note
5x clips
Release RH body harness from RH A - pillar area

Note
4x nylon ties, 2x tapes, When cutting nylon ties, do not cut the harness
Pull out RH body harness from RH IP
Release LH front cabin carpet cover

Note
2x magnets, 2x datums
Remove LH hush panel assembly

Note
6x clips, 1x connector
Release passenger footwell duct

Note
1x clip
Remove passenger footwell duct

Note
Maneuver footwell duct between IP assembly and glovebox
Remove console LH front side panel

Note
14x clips, 2x locating pins, Use trim tool starting at top edge to release upper clips, Pull bottom to release remaining clips, Use caution and pull panel straight away from console, If panel is peeled off it could be damaged
Disconnect RH body harness connectors on LH side of car computer

Note
3x connectors, Release locks on connectors before removal
Disconnect RH body harness connectors on RH side of car computer

Note
3x connectors, Release locks on connectors before removal
Release RH body harness from car computer

Note
3x clips
Move branch of RH car computer body harness to RH of vehicle

Note
4x clips
Disconnect accelerator pedal connector

Note
1x connector, 1x clip, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector
Release front main harness ground on RH A-pillar

Note
1x bolt, 10mm, 10 Nm
Disconnect front main harness from RH body harness

Note
1x connector, Release locking tab
Disconnect RH body harness from RH controller

Note
4x connectors, Connectors J2 J4 J5 J12, Release locking tabs
Disconnect windshield harness connectors from harness guide RH lower A pillar area

Note
3x connectors, Release lock then remove
Disconnect front main harness DCDC power cable

Note
1x connector, Release locking tab
Release front main harness DCDC power cable

Note
1x clip, 1x hook
Release RH body harness guide from RH lower A-pillar area

Note
3x clips
Release RH body harness clips from RH front sill area

Note
3x clips, 1x location pin
Disconnect LH body harness connectors from below RH front seat

Note
2x connectors, Disengage locking tab
Release RH body harness bracket clip from below RH front seat

Note
1x clip, 2x tabs
Remove RH B-pillar duct A section

Note
1x clip
Release RH harness clips from below RH B-pillar area

Note
6x clips
Release RH body harness clips from RH B-pillar side area

Note
3x clips
Disconnect RH front retractor connectors

Note
2x stage locking connectors, Lift the orange tab to release the connector
Disconnect RH B pillar accelerometer sensor connector

Note
1x connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector
Release grommet connector then remove RH rear door harness from B-pillar area

Note
1x connector, 2x clips, 1x grommet, Pry at both the top and then the bottom of rear door harness grommet while pulling away from B-pillar to release door harness
Remove RH rear door harness connector from B-pillar area

Note
3x clips, Release the connector clip from outer the B-pillar
Remove RH body harness ground strap from RH rear sill area

Note
1x bolt, 10mm, 10 Nm
Install inflatable air bag to support RH rear cabin carpet

Note
Use inflatable air bag to support the RH rear cabin carpet for enough space to remove harness, clip and nut
Remove clip securing 2nd row RH seat harness to ancillary bay

Note
1x clip, Please make sure to thread the harness of the second row seats through the carpet
Disconnect HVC logic connector and install logic cap

Note
1x connector, 1x cap, Release locking tab then push the handle downward to release connector
Release positive LV output cover from PCS cable

Note
1x cover
Remove PCS cable from LV passthrough output

Note
1x nut, 13mm, 9 Nm, Discard nut after removal
Release RH body harness from RH rear body

Note
1x clip
Release clips RH body harness to rear body and move aside

Note
2x clips
Partially release RH rear quarter panel NVH clips from body

Note
2x clips
Disconnect RH 2nd row retractor connector

Note
1x connector, Lift orange locking tab then release the connector
Remove rear headliner assembly

Note
3x clips, 1x location pin, 2x tether clips, Discard tether clips after removal, Release trim panel horizontally toward front of vehicle
Remove TCU assembly

Note
2x bolts, 13mm, 16 Nm, 1x datum, Attention: Do not remove the TCU excessively, and be cautious of the connectors at its rear.
Disconnect TCU connectors

Note
2x connectors, 1x hook, Disengage locking tab
Push open RH coat hook
Open RH coat hook bolt cover

Note
1x locking tab
Remove RH coat hook bolt

Note
1x bolt, T25, 2.5 Nm
Partially release RH rear section headliner from body

Note
4x clips, 3x tabs, 1x location pin, 1x tether, Discard tether clip after removal, Depress 2x tabs to remove tether from body side
Remove bolt securing RH C pillar air bag ramp assembly from body

Note
1x bolt, 10mm, 5 Nm
Remove RH C pillar air bag ramp assembly from body

Note
1x location tab, 1x metal clip
Disconnect liftgate harness connectors from body harness

Note
3x connectors, Disengage locking tab
Disconnect RH power strut connector

Note
1x connector
Disconnect radio tuner connectors

Note
2x connectors
Disconnect antenna amplifier connector

Note
1x connector
Disconnect harness connector for RH side curtain air bag

Note
1x connector, 2 stage locking connectors, Lift the white tab to release the connector
Disconnect headliner RH rear harness connector

Note
1x connector
Release RH body harness clips from around RH C-pillar area

Note
11x clips
Release RH body harness clips from rear head area

Note
8x clips
Disconnect subwoofer connector

Note
1x connector
Disconnect audio amplifier connectors

Note
4x connectors
Remove RH body harness ground strap from RH side trunk area

Note
1x bolt, 10mm, 10 Nm
Release RH body harness clips from RH side trunk area

Note
2x clips
Remove wheel chocks and push vehicle onto lift

Note
Recommend assistance, Note this vehicle can only be safely pushed for a very short distance and at very slow speed, close all doors enough as needed to fit between the lift and latch rear doors to prevent accidental closure, Replace wheel chocks once vehicle in correct position
Raise and support vehicle

Note
Ensure vehicle is not charging, Remove charging cable if it's plugged in
Remove LH rear fender garnish from vehicle

Note
12x clips, 1x location pin, Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish
Remove RH rear fender garnish from vehicle

Note
12x clips, 1x location pin, Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish
Apply masking tape around LH corner of rear upper fascia
Partially release LH rear trough trim

Note
3x clips
Remove bolt securing LH corner of rear fascia to body

Note
1x bolt, 10mm, 3.5 Nm
Remove screw securing LH rear fascia to body

Note
1x screw, 8mm, 2 Nm
Apply masking tape around RH corner of rear upper fascia
Partially release RH rear trough trim

Note
3x clips
Remove bolt securing RH corner of rear fascia to body

Note
1x bolt, 10mm, 3.5 Nm
Remove screw securing RH rear fascia to body

Note
1x screw, 8mm, 2 Nm
Raise vehicle fully and lower lift onto locks

Note
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Remove LH and RH push clips securing mid aero shield to wheel house liner

Note
2x clips
Remove mid aero shield

Note
11x bolts, 2x tabs, 10mm, 5 Nm
Release rear fascia diffuser

Note
7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers
Lower vehicle partially and set onto locks

Note
Raise lift off locks, Then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
Release rear fascia assembly from body

Note
1x connector, Recommend assistance, Place rear fascia on padded surface to avoid damage
Disconnect rear subframe harness connector and RH rear EPB connector

Note
2x connectors, Disengage locking tab
Release RH body harness clips from RH RUB area

Note
3x clips
Release RH body harness clips from rear fascia area

Note
2x clips
Push RH body harness through RH wheelhouse outer assembly

Note
1x grommet, Harness passes through RH wheelhouse outer assembly
Remove RH body harness from vehicle
Position RH body harness onto vehicle
Push RH body harness through RH wheelhouse outer assembly

Note
1x grommet, Harness passes through RH wheelhouse outer assembly, Make sure to install grommet in proper orientation
Secure RH body harness clips to RH RUB area

Note
3x clips
Connect rear subframe harness connector and RH rear EPB connector

Note
2x connectors, Engage red locking tab
Secure RH body harness clips to rear fascia area

Note
2x clips
Secure rear fascia assembly onto body

Note
1x connector, Recommend assistance
Install bolt securing LH corner of rear fascia to body

Note
1x bolt, 10mm, 3.5 Nm
Secure LH rear trough trim to rear fascia

Note
3x clips
Install screw securing LH rear fascia to body

Note
1x screw, 8mm, 2 Nm
Install bolt securing RH corner of rear fascia to body

Note
1x bolt, 10mm, 3.5 Nm
Secure RH rear trough trim to rear fascia

Note
3x clips
Install screw securing RH corner of rear fascia to body

Note
1x screw, 10mm, 2 Nm
Install LH rear fender garnish onto vehicle

Note
12x clips, 1x location pin, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
Install RH rear fender garnish to vehicle

Note
12x clips, 1x location pin, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
Remove masking tape from LH corner of rear upper fascia
Remove masking tape from RH corner of rear upper fascia
Raise vehicle fully and lower lift onto locks

Note
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Secure rear fascia diffuser

Note
7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers, Apply Loctite 222 onto bolts
lnstall mid aero shield

Note
2x tabs, 11x bolts, 10mm, 5 Nm, Position rear datums first, Apply Loctite 222 onto rear aero shield bolts
Lower vehicle fully

Note
Raise lift off locks, Then hold lock release lever to keep locks free while vehicle is lowered
Remove vehicle from lift

Note
Lower rack arms fully and remove from under vehicle
Push vehicle away from lift

Note
Recommend assistance, Place wheel chocks to keep vehicle from moving, Note this vehicle can only be safely pushed for a very short distance and at very slow speed
Secure RH body harness clips to RH side trunk area

Note
2x clips
Install RH body harness ground strap to RH side trunk area

Note
1x bolt, 10mm, 10 Nm
Connect audio amplifier connectors

Note
4x connectors
Connect subwoofer connector

Note
1x connector
Install RH body harness clips to around RH C-pillar area

Note
11x clips
Install RH body harness clips to RH rear head area

Note
8x clips
Connect headliner RH rear harness connector

Note
1x connector
Connect harness connector for RH side curtain air bag

Note
1x connector, Press the connector. When the connector is fully seated, you will hear the click sound of the secondary locking pin returning
Connect RH power strut connector

Note
1x connector
Connect liftgate harness connectors

Note
3x connectors, Engage locking tab
Connect radio truner connectors

Note
2x connectors
Connect antenna amplifier connector

Note
1x connector
Install RH C pillar air bag ramp assembly to body

Note
1x location tab, 1x metal clip
Install bolt securing RH C pillar air bag ramp assembly to body

Note
1x bolt, 10mm, 5 Nm
Partially secure RH rear section of headliner to body

Note
4x clips, 3x tabs, 1x location pin, 1x tether, Install new tether clip, Secure tether to body, Ensure that the seal covers the interior trim panel.
Install RH coat hook bolt

Note
1x bolt, T25, 2.5 Nm
Close RH coat hook bolt cover

Note
1x locking tab
Push RH coat hook closed
Connect TCU connectors

Note
2x connectors, 1x hook, Engage locking tab
Install TCU assembly

Note
2x bolts, 13mm, 16 Nm, 1x datum
lnstall rear headliner assembly

Note
3x clips, 1x location pin, 2x tether clips, Install new tether clips, Secure trim panel horizontally toward rear of vehicle.
Connect RH 2nd row retractor connector

Note
1x connector
Partially install RH rear quarter panel NVH clips to body

Note
2x clips
Fasten clips RH body harness to rear body

Note
2x clips
Install RH body harness onto rear body

Note
1x clip
Install positive LV output from PCS cable and torque nut securing it

Note
1x nut, 13mm, 9 Nm, Install new nut, Mark the nut after torque
Install positive LV output cover to PCS cable

Note
1x cover
Remove logic cap and connect HVC logic connector

Note
1x connector, 1x logic cap, Align connector then pull the handle to locking position get connector fully seated
Install clip securing 2nd row RH seat harness to ancillary bay

Note
1x clip, Please make sure to thread the harness of the second row seats through the carpet
Remove inflatable air bag to support RH rear cabin carpet
Install RH body harness ground strap to RH rear sill area

Note
1x bolt, 10mm, 10 Nm
Install RH rear door harness connector to B-pillar area

Note
3x clips
Install RH rear door harness connector to B-pillar

Note
1x connector, 2x clips, 1x grommet, Verify seal is fully seated around white clip prior to installation, Press RH rear door harness connector to body harness connector, Hold body harness connector in place till audible click is heard, Gently pull body harness connector to ensure its secure, Ensure door harness grommet is seated to B-pillar
Connect RH B pillar accelerometer sensor connector

Note
1x connector, Engage locking tab
Connect RH front retractor connectors

Note
2x connectors, Press the connector. When the connector is fully seated, You will hear the click sound of the secondary locking pin returning,If new body harness does not have connector for the ALR connector, secure ALR connector tree clip into original position
Secure RH body harness clips to RH B-pillar side area

Note
3x clips
Secure RH harness clips from below RH B-pillar area

Note
6x clips
Install RH B-pillar duct A section

Note
1x clip
Secure RH body harness bracket clip to below RH front seat

Note
1x clip, 2x tabs
Connect LH body harness connectors to below RH front seat

Note
2x connectors, Engage locking tab
Secure RH body harness clips to RH front sill area

Note
3x clips, 1x location pin
Secure RH body harness guide to RH lower A-pillar area

Note
3x clips
Secure front main harness DCDC cable to RH harness bracket

Note
1x clip, 1x hook
Connect front main harness DCDC cable connector to RH body harness

Note
1x connector, Engage locking tab
Connect windshield harness connectors to harness guide RH lower A pillar area

Note
3x connectors, Engage locking tab
Connect RH body harness to RH controller

Note
4x connectors, Connectors J2 J4 J5 J12, Engage locking tabs
Connect connector to RH controller

Note
1x connector, Engage locking tab
Secure front main harness ground on RH A-pillar

Note
1x bolt, 10mm, 10 Nm
Connect accelerator pedal connector

Note
1x connector, 1x clip, Engage locking tab
Move branch of RH car computer body harness to LH of vehicle

Note
4x clips
Install RH body harness to car computer

Note
3x clips
Connect RH body harness connectors to RH side of car computer

Note
3x connectors, Engage locking tabs after install
Connect RH body harness connectors to LH side of car computer

Note
3x connectors, Engage locking tabs after install
Install console LH front side panel

Note
14x clips, 2x locating pins, Ensure all clips and pins seat propely
Position passenger footwell duct

Note
Maneuver footwell duct between IP assembly and glovebox, fully install footwell duct onto HVAC
Install passenger footwell duct

Note
1x clip
Install LH hush panel

Note
6x clips, 1x connector
Secure LH front cabin carpet cover

Note
2x magnets, 2x datums, Align air vents with grills
Thread RH body harness through RH IP
Secure RH body harness to RH A - pillar area

Note
4x nylon ties, 2x tapes
Secure RH body harness clips to front head area

Note
5x clips
Install front windshield harness to A - pillar area

Note
4x clips
Connect interior radar

Note
1x connector, Secure red locking tab
Connect connector to interior endpoint

Note
1x connector, Engage locking tab
Install front end of headliner

Note
5x clips, 1x location pin, Pull seal over headliner
Install RH sun visor to headliner

Note
1x screw, T25, 3.5 Nm, 1x connector, Fold sunvisor to the closed and folded down position but do not latch in place
Install RH sun visor bracket cover

Note
4x tabs
Install RH upper A pillar trim

Note
5x clips, 2x guide tabs, 1x datum, 1x tether, Slide lower section of trim into slot on IP, Secure tether to body, Engage clips working bottom to top, Ensure primary seal rests over trim, Tether may vary by revision
Install LH sun visor to headliner

Note
1x screw, T25, 3.5 Nm, 1x connector, Fold sun visor to theclosed and folded down position but do not latch in place
Install LH sun visor bracket cover

Note
4x tabs
Install LH upper A pillar trim

Note
5x clips, 2x guide tabs, 1x datum, 1x tether, Slide lower section of trim into slot on IP, Secure tether to body, Engage clips working bottom to top, Ensure primary seal rests over trim, Tether may vary by revision
Install LH IP end cap

Note
5x clips, 2x guide tabs
Install LH front primary door seal

Note
Verify seal is seated properly on all trim panels
Install RH front cabin carpet to vehicle

Note
2x push clips, Make sure the carpet fully seated on corrcet position
Install console RH front side panel

Note
15x clips, 3x locating pins, Ensure all clips and pins fully seated
Install driver footwell hush panel

Note
1x connector, 7x tabs, 2x location pins, Align air vent with grill
Secure front RH cabin carpet cover to driver footwell hush panel

Note
2x magnets, 2x datums
Install RH B pillar lower air duct to body

Note
1x edge clip
Install RH upper B pillar trim assembly onto body

Note
5x clips, 2x location pins, Lower the seat belt slider to align it with the B-pillar panel, align the location pin of the B-pillar upper trim panel with the slot, push in the direction of the arrow to install the clips after aligning them, Install lower air vent
Install RH lower B pillar trim

Note
2x location pins, 8x clips, 1x push clip, Align the locator tab to slot, push in the direction of the arrow to install the clips after aligning them, then install both side tabs
Replace double-sided tape on B-pillar applique seal

Note
Cut two sections of tape to match original adhesive strips, Apply to seal at indicated locations
Connect RH B-pillar camera connectors

Note
2x connectors, Engage locking tab
Install RH B-pillar applique onto vehicle

Note
3x clips,1x location pin, 1x guide tab, Slide B-pillar applique up into position, Ensure trim clips are lined up, gently engage and lock clips
Secure upper RH B-pillar seal

Note
1x trim clip, Position upper RH B-pillar seal, engage trim clip and secure to body
Secure lower RH B-pillar seal

Note
2x double sided tape, Gently press areas of double sided tape to engage and secure to body
Install RH 3rd row duct B section to vehicle

Note
1x edge clip, 2x tabs
Secure RH upper C pillar trim clips to body

Note
10x clips, 4x location pins, 3x guide tabs, It is necessary to note that the air vent must be fully joined, Seat seal around edge of trim.
Position RH trunk side trim assembly to vehicle

Note
1x clip
Connect RH 3rd row seat switch connector

Note
1x connector
Secure RH trunk side trim clips to body

Note
14x clips, 2x location pins, 2x gudie tabs, Seat seal around edge of trim
Install RH trunk pocket bracket

Note
2x clips
Install RH lower C pillar trim to body

Note
7x clips, 1x guide tab, Align guide tab, Then press down to securing all clips
Partially install RH rear primary door seal onto body
Install 3rd row seatback complete onto vehicle

Note
2x location pins, Recommended assistant assistance
Loosely install inner bolts securing 3rd row seatback complete to body

Note
2x bolts, 11mm, 37 Nm, Install new bolts, Install bolts hand tight, Torque at later step
Loosely install outer bolts securing 3rd row seatback complete to body

Note
2x bolts, 11mm, 37 Nm, Install new bolts, Install bolts hand tight, Torque at later step
Loosely install bolt securing 3rd row RH front bracket outboardto body

Note
1x bolt, 11mm, 37 Nm, Install new bolt, Install bolt hand tight, Torque at later step
Loosely install bolt securing 3rd row LH front bracket outboardto body

Note
1x bolt, 11mm, 37 Nm, Install new bolt, Install bolt hand tight, Torque at later step
Torque inner bolts securing 3rd row seatback complete to body

Note
2x bolts, 11mm, 37 Nm
Torque outer bolts securing 3rd row seatback complete to body

Note
2x bolts, 11mm, 37 Nm
Torque bolt securing 3rd row RH front bracket outboard to body

Note
1x bolt, 11mm, 37 Nm
Torque bolt securing 3rd row LH front bracket outboard to body

Note
1x bolt, 11mm, 37 Nm
Connect 3rd row RH seat frame harness connector

Note
1x connector
Connect 3rd row LH seat frame harness connector

Note
1x connector
Install 3rd row RH seat cushion bolster

Note
1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide RH seat cushion bolster into seat frame complete
Install clip securing 3rd row RH seat frame harness to seat cushion bolster

Note
1x clip
Install 3rd row LH seat cushion bolster

Note
1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide LH seat cushion bolster into seat frame complete
Install clip securing 3rd row LH seat frame harness to seat cushion bolster

Note
1x clip
Connect 3rd row seat harness connector and secure seats cushion complete

Note
2x clips, 1x connector, 2x circular hooks, Insert buckles through holes, Slide rear inward then align front clips, Perform push-pull-push test
Install trunk tub onto vehicle

Note
2x push clips, 2x location holes
Install RH load floor bracket onto vehicle

Note
5x clips, 2x location pins
Install LH load floor bracket onto vehicle

Note
5x clips, 2x location pins
Install trunk sill trim onto vehicle

Note
4x clips, 2x location pins, Seat seal around edge of trim
Install trunk load floor onto vehicle
Install RH 2nd row seat to vehicle

Note
Recommend assistance, Caution not to damage any trim
Connect RH 2nd row seat connector

Note
1x connector, 1x clip, Partily lift seat assembly, Engage red locking tab
Install RH front seat into vehicle

Note
Recommend assistance, Install seat from front RH door opening, Assistant should be ready to support seatback once it is in the vehicle, Caution not to damage any trim
Secure RH front seat harness under RH front cabin carpet
Install RH front seat harness

Note
2x clips, 2x guide hooks, Tuck excess harness between harness bracket and body
Connect RH front seat harness to RH controller

Note
1x connector, Engage locking tab
Connect first responder loop and LV battery

Note
2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
Install HEPA filter assembly

Note
2x bolts, 10mm, 10 Nm, Pivot forward edge down past frunk assembly, Then carefully move rear edge past brake reservoir and into position, Gently press on RH side of filter to seat seal onto duct, Do not pinch washer hose inbetween HEPA filter assembly and body
Install rear apron

Note
16x trim clips, 3x locator pins, 2x clips, Replace any missing or damaged clips, Ensure pyrotechnic hood actuators are aligned with openings in apron
Close hood
Move RH 2nd row seat backward

Note
Adjust seat back if needed to avoid contacting other parts
Install RH 2nd row seat front bolts

Note
2x patch bolts, TP45, 33.5 Nm, Install new patch bolts
Move RH 2nd row seat forward

Note
Adjust seat back if needed
Install RH 2nd row seat rear bolts

Note
2x patch bolts, TP45, 33.5 Nm, Install new patch bolts
Move RH 2nd row seat to original position
Move RH front seat forward

Note
Adjust seatback if needed to avoid contacting headliner
Install seat belt retractor to RH front seat pre tensioner

Note
Insert retractor into seat pre tensioner, Make sure it locks into position with push-pull-push test
Install RH front seat rear bolts

Note
2x patch bolts, TP45, 33.5 Nm, Install new patch bolts
Move RH front seat backward
Install RH front seat front bolts

Note
2x patch bolts, TP45, 33.5 Nm, Install new patch bolts
Move RH front seat to original position
Install RH lower A pillar trim

Note
7x clips, 4x guide tabs, 1x push clip, Align front guide tabs then align slot with harness bracket and then push rear clip to secure, Make sure all clips and tabs fully seated
Install RH IP end cap

Note
5x clips, 2x guide tabs, Pull the seal over end cap
Install RH front primary door seal

Note
Verify seal is seated properly on all trim panels
ODIN 루틴 실행
ODIN 루틴 실행
PROC_EPB_X_SERVICE-MODE
via Service Mode:
Chassis ➜ Brakes ➜ EPB Service Mode
Chassis ➜ Brakes ➜ EPB Service Mode
via Service Mode Plus:Drive Unit ➜ Rear Drive Unit Replacement ➜ Release / Re-Engage Emergency Parking Brakevia Toolbox:(link)
ODIN 루틴 실행 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
Remove wheel chocks
Close liftgate
Raise all four windows
Close all four doors

Note
Unlatch doors before closing if necessary