교정 코드 00030700 FRT 0.84 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. Function check LH front door (exterior)
   참고

   Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions

   

2. Function check all windows from master switch
   참고

   Document any abnormal operation/noises

   

3. Function check wipers and spray jets
   참고

   Ensure hood and doors are closed prior to activating wipers, Inspect and note functionality for wipers and wiper jets, Check for full range of motion, speed of motion, interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions

   

4. Function check all driver controls
   참고

   Shift stalk, turn signals, steering wheel scroll wheels, horns

   

5. Function check exterior lights
   참고

   Recommend assistance, inspect and note functionality of Headlight (LH and RH), Side Repeater (LH and RH), Taillight (LH and RH), CHMSL, Fog Light (LH and RH), Reverse Light (LH and RH), Front Turn Signal (LH and RH), Rear Turn Signal (LH and RH)

   

   

   

6. Function check hazard light switch

   

7. Function check LH rear door (exterior)
   참고

   Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions

   

8. Function check RH rear door (exterior)
   참고

   Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions

   

9. Function check RH front door (exterior)
   참고

   Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions

   

10. Open hood

    

    

11. Remove rear apron
    참고

    16x trim clips, 3x location pins, 2x clips

    

    

    

    

12. Check brake fluid level
    참고

    Top off if necessary

    

13. Inspect coolant level and top off as necessary
    참고

    Ensure that fluid level is at Max line, Vacuum fill required if greater than 1L lost during repair

    

14. Fill washer reservoir with fluid

    

15. Install rear apron
    참고

    16x trim clips, 3x location pins, 2x clips, Replace any missing or damaged clips, Ensure pyrotechnic hood actuators are aligned with openings in apron

    

    

    

16. Close hood

    

    

17. Raise vehicle partially and lower lift onto locks
    참고

    Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side

    

    

18. Remove bolts securing front aero shield
    참고

    7x bolts, 10mm, 5 Nm

    

19. Remove front aero shield
    참고

    2x nuts, 15mm, 8 Nm

    

    

    

20. Remove rear aero shield clips
    참고

    2x clips, One clip on LH side wheel liner, One clip on RH side wheel liner

    

    

21. Remove rear aero shield
    참고

    11x bolts, 2x tabs, 10mm, 5 Nm

    

    

22. Remove LH rear suspension aero cover
    참고

    2x tabs, 1x bolt, 10mm, 5 Nm

    

    

23. Remove RH rear suspension aero cover
    참고

    2x tabs, 1x bolt, 10mm, 5 Nm

    

    

24. Record tread depth for LH rear tire
    참고

    Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less

    

25. Measure and record LH rear brake pad thickness
    참고

    Recommend replacement if 2mm or less, Check both inboard and outboard pads

    

26. Inspect LH rear brake rotor condition
    참고

    Check for excessive rust or wear, Minimum spec: See technical data

    

27. Record tread depth for RH rear tire
    참고

    Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less

    

28. Measure and record RH rear brake pad thickness
    참고

    Recommend replacement if 2 mm or less, Check both inboard and outboard pads

    

29. Inspect RH rear brake rotor condition
    참고

    Check for excessive rust or wear, Minimum spec : See technical data

    

30. Record tread depth for RH front tire
    참고

    Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less

    

31. Measure and record RH front brake pad thickness
    참고

    Recommend replacement if 2mm or less, Check both inboard and outboard pads

    

32. Record tread depth for LH front tire
    참고

    Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less

    

33. Measure and record LH front brake pad thickness
    참고

    Recommend replacement if 2mm or less, Check both inboard and outboard pads

    

34. Inspect LH front brake rotor condition
    참고

    Check for excessive rust or wear, Minimum spec: See technical data

    

35. Perform visual inspection of all brake pipes and hoses
    참고

    Pay special attention to brake junction points

    

    

36. Check all four tire pressures manually
    참고

    4x tires, Set to specification if necessary, Refer to the "Tire and Loading Information" label located on the driver side B-pillar, Inspect wheels and tires for any bulges or damage while checking/setting pressures

    

37. Raise vehicle fully and lower lift onto locks
    참고

    Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged

    

    

38. Perform visual inspection of HV battery enclosure
    참고

    Check for any dents, scrapes, or other damage

    

39. Inspect underside of vehicle for fluid leaks
    참고

    Pay special attention to hose connection points

    

    

40. Inspect RH front brake rotor condition
    참고

    Check for excessive rust or wear, Minimum spec: See technical data

    

41. Perform inspection of front suspension components
    참고

    Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed

    

    

    

    

    

    

    

42. Perform inspection of rear suspension components
    참고

    Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed

    

    

    

    

    

    

    

    

    

43. Perform inspection of steering components
    참고

    Check steering gear joints and electrical connections, Verify components are not bent or damaged

    

    

    

    

    

44. Install RH rear suspension cover
    참고

    2x tabs, 1x bolt, 10mm, 5 Nm, Apply Loctite 222 onto rear suspension cover bolt

    

    

    

45. Install LH rear suspension aero cover
    참고

    2x tabs, 1x bolt, 10mm, 5 Nm, Apply Loctite 222 onto rear suspension aero cover bolt

    

    

    

46. Install rear aero shield
    참고

    2x tabs, 11x bolts, 10mm, 5 Nm, Position rear datums first, Apply Loctite 222 onto rear aero shield bolts

    

    

    

    

47. Install rear aero shield clips
    참고

    2x clips, One clip on LH side wheel liner, One clip on RH side wheel liner

    

    

48. Position front aero shield onto vehicle
    참고

    2x datums, 2x nuts, 15mm, 8 Nm, Hand-tighten the nuts to temporarily hold the panel in place

    

    

    

49. Install front aero shield onto vehicle
    참고

    7x bolts, 10mm, 5 Nm, Apply Loctite 222 onto front aero shield bolts and install fasteners to front aero shield

    

    

50. Remove vehicle from lift
    참고

    Lower rack arms fully and remove from under vehicle

    

51. Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance
    참고

    The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present

    

52. Inspect vehicles alignment
    참고

    Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction