2025-06-27

Hose - Chiller To Battery - RHD (Remove and Replace)

교정 코드 1830020602 FRT 0.90 바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 ServiceManualFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오.참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

  • 2025-03-19: 새로운 절차가 공개되었습니다.

탈거

  1. RH 전면 도어를 열고 RH 전면 창문을 완전히 내립니다.
  2. 정비 모드를 활성화합니다. 참조 항목: 정비 모드.
  3. 차량 게이트웨이를 잠금 해제합니다. 참조 항목: 게이트웨이(잠금 해제).
  4. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드): PROC_VCFRONT_X_START-THERMAL-FILL-DRAINvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Start Thermal Fill/Drain
    • Thermal ➜ Coolant System ➜ Start Coolant Fill/Drain
    • Thermal ➜ Refrigerant System ➜ Start Refrigerant Fill/Drain
    via Service Mode Plus: Drive Inverter ➜ Front Drive Inverter Replacement ➜ Start Fluid Fill/Drain
  5. LV 전원을 연결 해제합니다. 참조 항목: LV Power (Disconnect and Connect) (Modify).
  6. 차량을 올려서 지탱합니다. 차량 들어 올리기 - 2 포스트 리프트를 참조하십시오.
  7. 전면 에어로 실드를 탈거합니다. 참조 항목: Aero Shield - Front (Remove and Replace).
  8. 냉각수 배출 용기를 HV 배터리의 LH 전면 아래에 배치합니다.
  9. 칠러-배터리 호스를 대시보드 크로스멤버에 고정하는 클립을 풉니다.
  10. 후면 후드 내 에이프런을 탈거합니다. 후드 내 에이프런 - 후면(탈거 및 교체)를 참조하십시오.
  11. HV 배터리 매니폴드 호스를 연결 해제한 다음 양쪽 호스에 플러그를 끼웁니다.
  12. 차량 밑에서 오일 배출 용기를 치운 다음 차량을 내립니다.
  13. 오일 배출 용기를 차량 전면 아래에 배치합니다.
  14. 서멀 빔에 외기 흡기 덕트를 고정하는 볼트를 탈거합니다(토크 4Nm).
  15. 벌크헤드의 스터드(2개)로부터 외기 흡기 덕트를 연결 해제한 다음 차량에서 덕트를 탈거합니다.
  16. 차량에서 LV 배터리를 탈거합니다. 참조 항목: LV Battery (Remove and Install).
  17. 칠러-배터리 호스를 A/C 컴프레서 브래킷에 고정하는 클립(2개)을 풉니다.
  18. 칠러-배터리 호스의 센서를 연결 해제합니다.
  19. 차량 컴퓨터 냉각수 연결부 아래에 흡수재를 배치하여 누출되는 냉각수를 수집합니다.
  20. 차량 컴퓨터 냉각수 호스를 차량 컴퓨터 냉각수 포트에 연결하는 스프링 클립(2개)을 푼 다음 호스를 연결 해제합니다.
  21. 차량 컴퓨터 냉각수 포트와 자동차 컴퓨터 냉각수 호스에 플러그를 끼웁니다.
  22. 칠러-HV 배터리 호스를 차량에서 탈거합니다.
    Informational PurposesAn informational icon, calling your attention
    참고
    차량 LH에서 호스를 탈거합니다.

장착

다음을 제외하고, 장착 절차는 탈거의 역순입니다.

  • LV 배터리를 장착하기 전 냉각수 진공 재충전을 수행합니다. 참조 항목: Cooling System - Vacuum Refill (Test/Adjust).
  • LV 배터리를 장착한 후 열 주입/배출 절차를 중단합니다. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드):PROC_VCFRONT_X_STOP-THERMAL-FILL-DRAINvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Stop Thermal Fill/Drain
    • Thermal ➜ Coolant System ➜ Stop Coolant Fill/Drain
    • Thermal ➜ Refrigerant System ➜ Stop Refrigerant Fill/Drain
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Stop Fluid Fill/Drain
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Stop Coolant Fill/Drain
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Stop Coolant Fill/Drain
  • 냉각수 공기 배출을 수행합니다.정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드):TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Toolbox: (link)via Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
  • 냉각수 수위를 검사하고 필요한 경우 보충합니다.