교정 코드 NEW 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

1. Open all four doors

   

2. Lower all four windows

   

3. Open hood

   

   

4. Open liftgate

   

   

5. ODIN 루틴 실행 PROC_ICE_X_ENTER-SERVICE-MODEvia Toolbox:(link)
6. ODIN 루틴 실행
7. Access chassis system routines using UI
   참고

   Select Chassis > Brakes

   

   

8. ODIN 루틴 실행 PROC_EPB_X_SERVICE-MODEvia Service Mode:
   • Chassis ➜ Brakes ➜ EPB Service Mode
   • Chassis ➜ Brakes ➜ EPB Service Mode
   via Service Mode Plus:Drive Unit ➜ Rear Drive Unit Replacement ➜ Release / Re-Engage Emergency Parking Brakevia Toolbox:(link)
9. Set wheel chocks
   참고

   Warning: After this action, tire wedges will be set to prevent the vehicle from rolling freely

   

10. Partially remove LH front primary door seal from body

    

    

11. Remove LH IP end cap
    참고

    5x clips, 2x guide tabs

    

    

12. Remove LH lower A pillar trim from body
    참고

    7x clips,4x guide tabs, 1x push clip, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet

    

    

    

13. Release LH front seat harness from sill trim clips
    참고

    4x clips

    

    

14. Pull LH front seat harness from under LH front cabin carpet

    

15. Move LH front seat forward
    참고

    Adjust seat back if needed to avoid contacting headliner

    

16. Remove LH front seat rear bolts
    참고

    2x patch bolts, TP45, 33.5 Nm, Discard patch bolts after removal

    

17. Move LH front seat backward

    

18. Remove LH front seat front bolts
    참고

    2x patch bolts, TP45, 33.5 Nm, Discard patch bolts after removal

    

19. Release seat belt retractor from LH front seat pre tensioner
    참고

    Insert seat belt release tool in bottom of retractor to release

    

    

20. Partially release RH front primary door seal
    참고

    For remove RH IP end cap, RH lower A pillar trim, RH front B pillar trim

    

    

21. Remove RH IP end cap
    참고

    5x clips, 2x guide tabs

    

    

22. Remove RH lower A pillar trim
    참고

    7x clips, 4x guide tabs, 1x push clip, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet

    

    

    

    

23. Release RH front seat harness from sill trim clips
    참고

    4x clips

    

    

24. Pull RH front seat harness from under RH front cabin carpet

    

25. Move RH front seat forward
    참고

    Adjust seatback if needed to avoid contacting headliner

    

26. Remove RH front seat rear bolts
    참고

    2x patch bolts, TP45, 33.5 Nm, Discard patch bolts after removal

    

27. Move RH front seat backward

    

28. Remove RH front seat front bolts
    참고

    2x patch bolts, TP45, 33.5 Nm, Discard patch bolts after removal

    

29. Release seat belt retractor from RH front seat pre tensioner
    참고

    Insert seat belt release tool in bottom of retractor to release

    

    

    

30. Move LH 2nd row seat backward
    참고

    Adjust seat back if needed to avoid contacting other parts

    

31. Remove front bolts securing LH 2nd row seat
    참고

    2x patch bolts, TP45, 33.5 Nm, Discard patch bolts after removal

    

32. Move LH 2nd row seat forward
    참고

    Adjust seat back if needed

    

33. Remove rear bolts securing LH 2nd row seat
    참고

    2x patch bolts, TP45, 33.5 Nm, Discard patch bolts after removal

    

34. Adjust LH 2nd row seat position for removal
    참고

    Center seat on tracks to minimize risk of damage to trim during removal

    

    

35. Move RH 2nd row seat forward
    참고

    Adjust seat back if needed

    

36. Power off vehicle from center display
    참고

    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box

    

    

37. Remove rear apron
    참고

    16x trim clips, 3x datums, 2x clips

    

    

    

    

38. Remove HEPA filter assembly
    참고

    2x bolts, 10mm, 10 Nm, Pivot rear edge up past brake reservoir then lift up to clear frunk assembly

    

    

    

    

39. Disconnect LV battery and first responder loop
    참고

    2x connectors, Ensure that one minute has passed after window movement before performing the power-off, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge

    

    

    

    

    

40. Disconnect LH 2nd row seat connector
    참고

    1x connector, 1x clip, Partily lift seat assembly, Release red locking tab and then press white tab to disconnect connector

    

    

41. Remove LH 2nd row seat from vehicle
    참고

    Recommend assistance, Caution not to damage any trim, Protect the seat upholstery when the seat is outside of the vehicle

    

    

42. Disconnect LH front seat harness connector from LH controller
    참고

    1x connector, Release locking tab

    

    

43. Remove LH front seat from vehicle
    참고

    Recommend assistance, With assistant supporting seat back from 2nd row seat, Remove seat from front LH door opening, Caution not to damage any trim, Protect the seat upholstery when the seat is outside of the vehicle

    

    

    

44. Disconnect RH front seat harness connector from RH body controller
    참고

    1x connector, Release lock then remove

    

45. Remove RH front seat from vehicle
    참고

    Recommend assistance, With assistant supporting seatback from 2nd row seat, Remove seat from front RH door opening, Caution not to damage any trim, Protect the seat upholstery when the seat is outside of the vehicle

    

    

46. Remove trunk load floor from vehicle

    

    

47. Remove trunk sill trim from vehicle
    참고

    4x clips, 2x loaction pins

    

    

48. Remove LH load floor bracket from vehicle
    참고

    5x clips, 2x location pins

    

    

    

49. Remove RH load floor bracket from vehicle
    참고

    5x clips, 2x location pins

    

    

    

50. Remove trunk tub from vehicle
    참고

    2x push clips, 2x location holes

    

    

    

51. Remove 3rd row seat cushion
    참고

    2x clips, 1x connector, 2x circular hooks, Press tabs backward then pull front edge up, Press rear seat cushion and lift the front seat cushion

    

    

    

    

    

52. Release clip securing 3rd row LH seat frame harness to seat cushion bolster
    참고

    1x clip

    

    

53. Remove 3rd row LH seat cushion bolster
    참고

    1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide LH seat cushion bolster towards front of vehicle to remove

    

54. Release clip securing 3rd row RH seat frame harness to seat cushion bolster
    참고

    1x clip

    

    

55. Remove 3rd row RH seat cushion bolster
    참고

    1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide RH seat cushion bolster towards front of vehicle to remove

    

    

    

56. Disconnect 3rd row LH seat frame harness connector
    참고

    1x connector

    

57. Disconnect 3rd row RH seat frame harness connector
    참고

    1x connector

    

58. Remove bolt securing 3rd row RH front bracket outboard to body
    참고

    1x bolt, 11mm, 37 Nm, Discard bolt after removal

    

59. Remove bolt securing 3rd row LH front bracket outboard tobody
    참고

    1x bolt, 11mm, 37 Nm, Discard bolt after removal

    

60. Remove inner bolts securing 3rd row seatback complete to body
    참고

    2x bolts, 11mm, 37 Nm, Discard bolts after removal

    

61. Remove outer bolts securing 3rd row seatbelt and seat back
    참고

    2x bolts, 11mm, 37 Nm, Discard bolts after removal

    

    

62. Remove 3rd row seatback complete from vehicle
    참고

    2x location pins, First lift up, Then move the entire body backward, Remove 3rd row seatback complete through the liftgate, Recommended assistant assistance

    

    

    

63. Partially release LH rear primary door seal from body
    참고

    For remove LH lower C pillar trim, LH trunk side trim, LH upper C pillar trim.

    

    

64. Remove LH lower C pillar trim from body
    참고

    7x clips, 1x guide tab, Pull the trim upward to release all clips

    

    

65. Remove LH trunk pocket bracket
    참고

    2x clips, 1x metal clip, Removal may vary depending on vehicle build, 7-seater option may require using plastic trim tool remove pocket bracket, Use thick portion of part’s material as pry point

    

    

    

    

    

66. Release LH trunk side trim clips from body
    참고

    14x clips, 2x location pins, 2x guide tabs, Release the LH trunk side trim clips to facilitate the removal of the C pillar upper trim.

    

    

    

    

67. Disconnect LH 3rd row seat switch connector
    참고

    1x connector

    

68. Remove trunk side trim assembly from vehicle
    참고

    1x clip, 1x power outlet connector

    

    

    

69. Release LH upper C pillar trim clips from body then move aside
    참고

    10x clips, 4x location pins, 3x guide tabs, 1x dump switch connector, 1x release cable, Do not remove the decorative trim after it is released, as there is a charging port release cable and seat switch connector at the rear of the trim

    

    

    

    

    

70. Remove LH 3rd row duct B section from vehicle
    참고

    1x edge clip, 2x tabs

    

    

    

    

71. Remove rear end lower panel assembly from center console
    참고

    5x clips, 3x guide pins, 2x tabs, Parallel backward removal, Attention, be careful when removing as there is a speaker connector at the rear end lower panel

    

    

    

    

72. Disconnect cup holder speaker connector
    참고

    1x connector

    

73. Remove rear bolts securing center console to vehicle
    참고

    2x bolts, 10mm, 7 Nm

    

    

74. Remove console LH front side panel from center console
    참고

    14x clips, 1x location pin, Use trim tool starting at top edge to release upper clips, Pull bottom to release remaining clips, Use caution and pull panel straight away from console, If panel is peeled off it could be damaged

    

    

75. Remove LH front exterior bolts from center console
    참고

    2x bolts, 10mm, 7 Nm

    

76. ODIN 루틴 실행
77. Remove RH front exterior bolts from center console
    참고

    2x bolts, 10mm, 7 Nm

    

78. Release center console connector
    참고

    1x connector

    

79. Disconnect harness connector from right front of center console
    참고

    1x connector, 1x clip

    

    

80. Remove center console assembly from vehicle
    참고

    Tilt rear of console upward, Pull assembly towards rear of vehicle, Then tilt front of console upward and remove through second row, Recommended assistant support

    

    

81. Release LH front cabin carpet cover
    참고

    2x magnets, 2x datums

    

    

82. Release OBD port from LH cabin carpet cover
    참고

    2x tabs, Press black tabs to unlock then push upwards out of footwell cover

    

    

83. Disconnect E-CALL speaker connector
    참고

    1x connector

    

84. Remove LH hush panel assembly
    참고

    6x clips, 1x connector

    

    

    

85. Remove LH front cabin carpet
    참고

    2x push clips

    

    

    

86. Release front RH cabin carpet cover from driver footwell hush panel
    참고

    2x magnets, 2x datums

    

    

87. Remove driver footwell hush panel
    참고

    1x connector, 7x tabs, 2x location pins

    

    

88. ODIN 루틴 실행
89. Partially release LH rear primary door seal from body
    참고

    For remove LH rear B pillar trim, LH lower C pillar trim

    

    

90. Remove LH lower B pillar trim from body
    참고

    2x location pins, 8x clips, 1x push clip, Release top side clips. Pull upper then lower half trim inward to release all clips.

    

    

    

    

    

91. Release clip securing LH B pillar lower air duct from body
    참고

    1x edge clip

    

92. Remove LH upper B pillar trim assembly from body then move aside
    참고

    5x clips, 2x location pins, Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips.

    

    

    

    

    

93. Remove LH B pillar duct B section from vehicle
    참고

    2x tabs

    

    

    

94. Remove double-sided tape underneath LH B-pillar applique

    

    

95. Release LH upper B-pillar applique clip from body
    참고

    1x clip, Insert the clip molding remover tool into the position 7.5cm below the left B-pillar camera, Ensuring that the tool is located under the B-pillar trim seal

    

    

96. Release LH lower B-pillar applique clips from body
    참고

    2x clips, 1x location pin, Insert the clip molding removal tool into the bottom of the left B-pillar, Facing upwards by 6cm position, Ensure tool is below B-pillar applique seal

    

    

97. Slide LH B-pillar applique down
    참고

    1x guide tab, Slide B-pillar applique down slightly to release assembly from body, Camera harness is connected, Do not fully remove applique

    

    

98. Release LH applique seal clip and remove from body
    참고

    1x trim clip, Slide clip prytool underneath clip to disengage from body, Clip is glued to seal, If prytool is engaged at seal clip will tear away

    

    

99. Disconnect B-pillar NFC connector
    참고

    1x connector, Disengage locking tab

    

    

100. Disconnect LH B-pillar camera connector
     참고

     1x connector

     

     

     

101. Clean residual adhesive from LH B-pillar and clean surface with IPA wipe
     참고

     Allow 1 minute for IPA to dry

     

     

102. Clean residual adhesive from LH B-pillar applique

     

     

103. Replace double-sided tape on B-pillar applique seal
     참고

     Cut two sections of tape to match original adhesive strips, Apply to seal at indicated locations

     

104. Disconnect front main harness from LH body harness
     참고

     1x connector, Connector X909

     

105. Disconnect LH body harness from left controller
     참고

     3x connectors, Connector J2, Connector J4, Connector J5, Release locking tabs

     

     

     

106. Release front main harness ground on LH A-pillar
     참고

     1x bolt, 10mm, 10 Nm

     

107. Disconnect headliner harness connector
     참고

     1x connector, Release locking tab

     

108. Release LH body harness clips from LH A-pillar
     참고

     3x clips

     

     

109. Release LH body harness from LH front sill
     참고

     3x clips, 1x datum

     

     

110. Partially release left and right second row carpet
     참고

     4x clips, The partially raised carpet makes it convenient to remove the wiring harness

     

     

     

     

111. Release LH body harness clips under front seats and center console
     참고

     3x clips, 1x guide pin

     

     

     

112. Remove harness clip from 3rd row head duct
     참고

     1x clip

     

113. Disconnect LH body harness connector from RCM
     참고

     1x connector, Disengage locking tab

     

114. Disconnect LH body harness connectors from below RH front seat
     참고

     2x connectors, Disengage locking tab

     

115. Remove LH B-pillar duct A section
     참고

     1x clip, First remove clip, Then disconnect duct connection, And remove it upward

     

     

     

     

116. Release LH body harness from lower B-pillar
     참고

     5x clips

     

     

117. Release LH body harness from upper B-pillar
     참고

     3x clips, Pull harness section into cabin from applique area

     

     

     

118. Disconnect LH front retractor connectors
     참고

     2x stage locking connectors, Lift the orange tab to release the connector

     

119. Disconnect LH B pillar accelerometer sensor connector
     참고

     1x connector, Do not push down on Red tab, Pull red tab to disengage lock, Pull again to release connector

     

120. Disconnect LH rear door harness connector from B-pillar area
     참고

     1x connector, 2x clips

     

     

121. Remove LH body harness from under front seats and center console
     참고

     Ensure that the LH body harness is drawn without resistance

     

122. Remove LH body harness ground strap from LH rear sill area
     참고

     1x bolt, 10mm, 10 Nm

     

123. Install inflatable air bag to support LH rear cabin carpet
     참고

     Use inflatable air bag to support the LH rear cabin carpet for enough space to remove the busbar bolt

     

124. Remove clip securing 2nd row LH seat harness to ancillary bay
     참고

     1x clip, Please make sure to thread the harness of the second row seats through the carpet

     

     

125. Release LH body harness from rear body and move aside
     참고

     1x clip

     

126. Release clips LH body harness to rear body and move aside
     참고

     2x clips

     

127. Partially release LH rear quarter panel NVH clips from body
     참고

     2x clips

     

128. Disconnect LH 2nd row retractor connector
     참고

     1x connector, Lift orange locking tab then release the connector

     

     

129. Remove rear headliner assembly
     참고

     3x clips, 1x location pin, 2x tether clips, Discard tether clips after removal, Release trim panel horizontally toward front of vehicle

     

     

     

     

     

130. Push open LH coat hook

     

     

131. Open LH coat hook bolt cover
     참고

     1x locking tab

     

     

132. Remove LH coat hook bolt
     참고

     1x bolt, T25, 2.5 Nm

     

133. Partially release LH rear section headliner from body
     참고

     4x clips, 3x tabs, 1x location pin, 1x tether, Depress 2x tabs to remove tether from body side

     

     

     

     

     

134. Remove bolt securing LH C pillar air bag ramp assembly from body
     참고

     1x bolt, 10mm, 5 Nm

     

135. Remove LH C pillar air bag ramp assembly from body
     참고

     1x location tab, 1x metal clip

     

     

136. Disconnect LH power strut connector
     참고

     1x connector

     

137. Disconnect harness connector for LH side curtain air bag
     참고

     1x connector, 2 stage locking connectors, Lift the white tab to release the connector

     

     

138. Release LH body harness clips around LH C-pillar area
     참고

     14x clips

     

     

     

139. Disconnect LH body harness from charge port ECU
     참고

     2x connectors

     

140. Remove LH body harness ground strap from LH side trunk area
     참고

     1x bolt, 10mm, 10 Nm

     

141. Disconnect connectors from chargeport assembly
     참고

     2x connectors, Disengage locking tab

     

142. Remove wheel chocks and push vehicle onto lift
     참고

     Recommend assistance, Note this vehicle can only be safely pushed for a very short distance and at very slow speed, close all doors enough as needed to fit between the lift and latch rear doors to prevent accidental closure, Replace wheel chocks once vehicle in correct position

     

143. Raise and support vehicle
     참고

     Ensure vehicle is not charging, Remove charging cable if it's plugged in

     

     

     

144. Remove LH rear fender garnish from vehicle
     참고

     12x clips, 1x location pin, Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish

     

     

     

145. Remove RH rear fender garnish from vehicle
     참고

     12x clips, 1x location pin, Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish

     

     

     

146. Apply masking tape around LH corner of rear upper fascia

     

147. Release LH trough trim lower clips from rear fascia
     참고

     3x clips

     

     

148. Remove bolt securing LH corner of rear fascia to body
     참고

     1x bolt, 10mm, 3.5 Nm

     

149. Remove screw securing LH rear fascia to body
     참고

     1x screw, 8mm, 2 Nm

     

150. Apply masking tape around RH corner of rear upper fascia

     

151. Release RH trough trim lower clips from rear fascia
     참고

     3x clips

     

     

152. Remove bolt securing RH corner of rear fascia to body
     참고

     1x bolt, 10mm, 3.5 Nm

     

153. Remove screw securing RH rear fascia to body
     참고

     1x screw, 8mm, 2 Nm

     

154. Raise vehicle fully and lower lift onto locks
     참고

     Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged

     

     

155. Remove rear fascia diffuser front bolts
     참고

     2x bolts, 10mm, 5 Nm

     

156. Release rear fascia diffuser
     참고

     7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers

     

     

     

     

     

157. Lower vehicle partially and set onto locks
     참고

     Raise lift off locks, Then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height

     

     

     

158. Release rear fascia assembly from body
     참고

     1x connector, Disengage locking tab, Recommend assistance, Place rear fascia on padded surface to avoid damage

     

     

     

     

159. Release LH body harness clips fromt body
     참고

     2x clips

     

160. Remove LH body harness from rear fascia center brkt
     참고

     1x harness clip, 2x tabs

     

     

161. Raise vehicle fully and lower lift onto locks
     참고

     Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged

     

     

162. Disconnect LH rear EPB harness connector
     참고

     1x connector, Disengage yellow locking tab

     

163. Release LH body harness clips from LH RUB area
     참고

     2x clips

     

164. Lower vehicle partially and set onto locks
     참고

     Raise lift off locks, Then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height

     

     

     

165. Push LH body harness through LH wheelhouse outer assembly
     참고

     1x grommet, Harness passes through LH wheelhouse outer assembly

     

166. Remove LH body harness from vehicle

     

     

167. Position LH body harness onto vehicle

     

     

168. Push LH body harness through LH wheelhouse outer assembly
     참고

     1x grommet, Harness passes through LH wheelhouse outer assembly, Make sure to install grommet in proper orientation

     

     

169. Raise vehicle fully and lower lift onto locks
     참고

     Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged

     

     

170. Secure LH body harness clips to LH RUB area
     참고

     2x clips

     

171. Connect LH rear EPB harness connector
     참고

     1x connector, Engage yellow locking tab

     

172. Lower vehicle partially and set onto locks
     참고

     Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height

     

     

173. Install LH body harness clips fromt body
     참고

     2x clips

     

174. Installl LH body harness to rear fascia center brkt
     참고

     1x harness clip, 2x tabs

     

     

175. Secure rear fascia assembly onto body
     참고

     1x connector, Engage locking tab, Recommend assistance

     

     

     

     

176. Install bolt securing LH corner of rear fascia to body
     참고

     1x bolt, 10mm, 3.5 Nm

     

177. Secure LH trough trim lower clips onto rear fascia
     참고

     3x clips

     

     

178. Install screw securing LH rear fascia to body
     참고

     1x screw, 8mm, 2 Nm

     

179. Install LH rear fender garnish onto vehicle
     참고

     12x clips, 1x location pin, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish

     

     

     

180. Install bolt securing RH corner of rear fascia to body
     참고

     1x bolt, 10mm, 3.5 Nm

     

181. Secure RH trough trim lower clips onto rear fascia
     참고

     3x clips

     

     

182. Install screw securing RH corner of rear fascia to body
     참고

     1x screw, 10mm, 2 Nm

     

183. Install RH rear fender garnish onto vehicle
     참고

     12x clips, 1x location pin, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish

     

     

     

184. Remove masking tape from LH corner of rear upper fascia

     

185. Remove masking tape from RH corner of rear upper fascia

     

186. Raise vehicle fully and lower lift onto locks
     참고

     Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged

     

     

187. Secure rear fascia diffuser
     참고

     7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers, Apply Loctite 222 onto bolts

     

     

     

     

     

     

188. Install rear fascia diffuser front bolts
     참고

     2x bolts, 10mm, 5 Nm, Apply Loctite 222 onto rear aero shield bolts

     

     

189. Lower vehicle fully
     참고

     Raise lift off locks, Then hold lock release lever to keep locks free while vehicle is lowered

     

     

     

190. Remove vehicle from lift
     참고

     Lower rack arms fully and remove from under vehicle

     

191. Push vehicle away from lift
     참고

     Recommend assistance, Place wheel chocks to keep vehicle from moving, Note this vehicle can only be safely pushed for a very short distance and at very slow speed

     

192. Connect connectors to chargeport assembly
     참고

     2x connectors, Engage locking tab

     

193. Install LH body harness ground strap to LH side trunk area
     참고

     1x bolt, 10mm, 10 Nm

     

194. Secure LH body harness clips around LH C-pillar area
     참고

     14x clips

     

     

     

195. Connect harness connector for LH side curtain air bag
     참고

     1x connector, Press the connector. When the connector is fully seated, you will hear the click sound of the secondary locking pin returning

     

196. Connect LH power strut harness connector
     참고

     1x connector

     

197. Install LH C pillar air bag ramp assembly onto body
     참고

     1x location tab, 1x metal clip

     

     

198. Install bolt securing LH C pillar air bag ramp assembly to body
     참고

     1x bolt, 10mm, 5 Nm

     

199. Partially secure LH rear section of headliner to body
     참고

     4x clips, 3x tabs, 1x location pin, 1x tether, Secure tether to body, Ensure that the seal covers the interior trim panel

     

     

     

     

     

     

200. Install LH coat hook bolt
     참고

     1x bolt, T25, 2.5 Nm

     

201. Close LH coat hook screw cover
     참고

     1x locking tab

     

     

202. Push LH coat hook closed

     

     

203. lnstall rear headliner assembly
     참고

     3x clips, 1x location pin, 2x tether clips, Install new tether clips, Secure trim panel horizontally toward rear of vehicle.

     

     

     

     

204. Connect LH 2nd row retractor connector
     참고

     1x connector, When the connector is fully seated, You will hear the "click" sound

     

     

205. Partially secure LH rear quarter panel NVH clips to body
     참고

     2x clips

     

206. Fasten clips LH body harness to rear body
     참고

     2x clips

     

207. Install LH body harness onto rear body
     참고

     1x clip

     

208. Install clip securing 2nd row LH seat harness to body
     참고

     1x clip, Please make sure to thread the harness of the second row seats through the carpet

     

     

209. Remove inflatable air bag from LH rear cabin carpet

     

210. Install LH body harness to under front seats and center console
     참고

     Ensure there is no resistance when arranging the LH body harness

     

211. Install LH rear door harness connector to B-pillar area
     참고

     1x connector, 2x clips

     

     

212. Connect LH B pillar accelerometer sensor connector
     참고

     1x connector, Engage locking tab

     

213. Connect LH front retractor connectors
     참고

     2x connectors, Press the connector. When the connector is fully seated, You will hear the click sound of the secondary locking pin returning

     

214. Secure LH body harness to upper B-pillar
     참고

     3x clips, Feed applique section of harness through body opening

     

     

     

215. Secure LH body harness to lower B-pillar
     참고

     5x clips

     

     

216. Connect LH body harness connectors to below RH front seat
     참고

     2x connectors, Engage locking tab

     

217. Connect LH body harness connector to RCM
     참고

     1x connector, Engage locking tab

     

218. Install harness clip to 3rd row head duct
     참고

     1x clip

     

219. Secure LH body harness clips under front seats and center console
     참고

     3x clips, 1x guide pin

     

     

     

220. Install LH B-pillar duct A section
     참고

     1x clip, Pass duct through seat riser, Then connect the duct interface, And finally install the clip

     

     

     

     

221. Install left and right second row carpet
     참고

     4x clips, Make sure the duct is installed in place

     

     

     

     

     

     

222. Secure LH body harness clips to LH front sill area
     참고

     3x clips, 1x location pin

     

     

223. Secure LH body harness clips to LH A-pillar
     참고

     3x clips

     

     

224. Connect headliner harness connector
     참고

     1x connector, Engage locking tab

     

225. Secure front main harness ground on LH A-pillar
     참고

     1x bolt, 10mm, 10 Nm

     

226. Connect LH body harness to left controller
     참고

     3x connectors, Connectors J2 J4 J5, Engage locking tabs

     

     

     

227. Connect front main harness to LH body harness
     참고

     1x connector, Connector X909

     

228. Connect LH B-pillar camera connector
     참고

     1x connector

     

     

229. Connect LH B-pillar NFC connector
     참고

     1x connector, Engage locking tab

     

230. Install LH B-pillar applique onto vehicle
     참고

     2x clips,1x location pin, 1x guide tab, Slide B-pillar applique up into position, Ensure trim clips are lined up, gently engage and lock clips

     

     

     

     

     

231. Secure upper LH B-pillar seal clip
     참고

     1x trim clip, Position upper LH B-pillar seal, Engage trim clip and secure to body

     

     

232. Secure lower LH B-pillar seal
     참고

     2x double sided tape, Gently press areas of double sided tape to engage and secure to body

     

     

233. Install LH B pillar duct B section onto vehicle
     참고

     2x tabs

     

     

     

234. Install LH upper B pillar trim assembly onto body
     참고

     5x clips, 2x location pins, Slide the seat belt through the hole, Lower the seat belt slider to align it with the B-pillar panel, align the location pin of the B-pillar upper trim panel with the slot, push in the direction of the arrow to install the clips after aligning them, Install lower air vent

     

     

     

     

     

235. Restore clip securing LH lower air duct to body
     참고

     1x edge clip

     

236. Install LH lower B pillar trim onto body
     참고

     2x location pins, 8x clips, 1x push clip, Align the location tabs to slot, push in the direction of the arrow to install the clips after aligning them

     

     

     

     

     

237. Partially install LH rear primary door seal
     참고

     Verify seal is seated properly on all trim panels

     

     

238. Install RH front cabin carpet to vehicle
     참고

     2x push clips

     

     

     

     

239. Install driver footwell hush panel
     참고

     1x connector, 7x tabs, 2x location pins, Align air vent with grill

     

     

     

240. Secure front RH cabin carpet cover to driver footwell hush panel
     참고

     2x magnets, 2x datums

     

     

241. Install LH front cabin carpet
     참고

     2x push clips, Ensure carpet seated properly

     

     

     

242. Connect E-CALL speaker connector
     참고

     1x connector

     

243. Install OBD port
     참고

     2x tabs, Ensure black tabs in lock position

     

     

244. Install LH hush panel
     참고

     6x clips, 1x connector

     

     

     

245. Secure LH front cabin carpet cover
     참고

     2x magnets, 2x datums, Align air vents with grills

     

     

246. Install center console assembly to vehicle
     참고

     Tilt front of console downward, Slide assembly towards front of vehicle and tilt rear of console down into place

     

     

247. Connect harness connector to right front of center console
     참고

     1x connector, 1x clip

     

     

248. Secure center console connector
     참고

     1x connector

     

249. Install RH front exterior bolts to center console
     참고

     2x bolts, 10mm, 7 Nm

     

250. Install console RH front side panel to center console
     참고

     15x clips, 1x location pin, Ensure all clips and pin seat properly

     

     

251. Install LH front exterior bolts to center console
     참고

     2x bolts, 10mm, 7 Nm

     

252. Install console LH front side panel to center console
     참고

     14x clips, 1x location pin, Ensure all clips and pin seat properly

     

     

253. Install rear bolts securing center console to vehicle
     참고

     2x bolts, 10mm, 7 Nm

     

     

254. Connect cup holder speaker connector
     참고

     1x connector

     

255. Install rear end lower panel assembly to center console
     참고

     5x clips, 3x guide pins, 2x tabs, Parallel forward installation

     

     

     

     

     

256. Install LH 3rd row duct B section to vehicle
     참고

     1x edge clip, 2x tabs

     

     

     

     

257. Secure LH upper C pillar trim clips to body
     참고

     10x clips, 4x location pins, 3x guide tabs, 1x dump switch connector, 1x release cable, When installing, it is necessary to note that the air vents must be fully joined, Seat seal around edge of trim.

     

     

     

     

     

     

258. Position trunk side trim assembly to vehicle
     참고

     1x clip, 1x power outlet connector

     

     

     

259. Connect LH 3rd row seat switch connector
     참고

     1x connector

     

260. Secure LH trunk side trim clips to body
     참고

     14x clips, 2x location pins, 2x gudie tabs, Seat seal around edge of trim

     

     

     

     

261. Position trunk side trim assembly to vehicle
     참고

     1x clip, 1x power outlet connector

     

     

     

262. Connect LH 3rd row seat switch connector
     참고

     1x connector

     

263. Secure LH trunk side trim clips to body
     참고

     14x clips, 2x location pins, 2x gudie tabs, Seat seal around edge of trim

     

     

     

     

264. Install LH trunk pocket bracket
     참고

     2x clips, 1x metal clip, Installation may vary depending on vehicle build, 7-seater option may require using plastic trim tool install pocket bracket, Use thick portion of part’s material as pry point

     

     

     

     

     

265. Install LH lower C pillar trim onto body
     참고

     7x clips, 1x guide tab, Align guide tabs, Then press down to securing all clips

     

     

266. Partially install LH rear primary door seal onto body

     

267. Install 3rd row seatback complete onto vehicle
     참고

     2x location pins, Recommended assistant assistance

     

     

     

268. Loosely install inner bolts securing 3rd row seatback complete to body
     참고

     2x bolts, 11mm, 37 Nm, Install new bolts, Install bolts hand tight, Torque at later step

     

269. Loosely install outer bolts securing 3rd row seatback complete to body
     참고

     2x bolts, 11mm, 37 Nm, Install new bolts, Install bolts hand tight, Torque at later step

     

     

270. Loosely install bolt securing 3rd row LH front bracket outboardto body
     참고

     1x bolt, 11mm, 37 Nm, Install new bolt, Install bolt hand tight, Torque at later step

     

271. Loosely install bolt securing 3rd row RH front bracket outboardto body
     참고

     1x bolt, 11mm, 37 Nm, Install new bolt, Install bolt hand tight, Torque at later step

     

272. Torque inner bolts securing 3rd row seatback complete to body
     참고

     2x bolts, 11mm, 37 Nm

     

273. Torque outer bolts securing 3rd row seatback complete to body
     참고

     2x bolts, 11mm, 37 Nm

     

     

274. Torque bolt securing 3rd row RH front bracket outboard to body
     참고

     1x bolt, 11mm, 37 Nm

     

275. Connect 3rd row RH seat frame harness connector
     참고

     1x connector

     

276. Torque bolt securing 3rd row LH front bracket outboard to body
     참고

     1x bolt, 11mm, 37 Nm

     

277. Connect 3rd row LH seat frame harness connector
     참고

     1x connector

     

278. Install 3rd row RH seat cushion bolster
     참고

     1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide RH seat cushion bolster into seat frame complete

     

     

     

279. Install clip securing 3rd row RH seat frame harness to seat cushion bolster
     참고

     1x clip

     

     

280. Install 3rd row LH seat cushion bolster
     참고

     1x bolt, 11mm, 37 Nm, 1x location pin, 1x tab, Slide LH seat cushion bolster into seat frame complete

     

     

281. Install clip securing 3rd row LH seat frame harness to seat cushion bolster
     참고

     1x clip

     

     

282. Connect 3rd row seat harness connector and secure seats cushion complete
     참고

     2x clips, 1x connector, 2x circular hooks, Insert buckles through holes, Slide rear inward then align front clips, Perform push-pull-push test

     

     

     

     

283. Install trunk tub onto vehicle
     참고

     2x push clips, 2x location holes

     

     

     

284. Install RH load floor bracket onto vehicle
     참고

     5x clips, 2x location pins

     

     

     

285. Install LH load floor bracket onto vehicle
     참고

     5x clips, 2x location pins

     

     

     

286. Install trunk sill trim onto vehicle
     참고

     4x clips, 2x location pins, Seat seal around edge of trim

     

     

     

287. Install trunk load floor onto vehicle

     

     

288. Close liftgate

     

     

289. Install RH front seat into vehicle
     참고

     Recommend assistance, Install seat from front RH door opening, Assistant should be ready to support seatback once it is in the vehicle, Caution not to damage any trim

     

     

290. Secure RH front seat harness under RH front cabin carpet

     

291. Install clips securing RH seat harness to sill trim
     참고

     4x clips, Tuck excess harness between harness bracket and body

     

     

292. Connect RH front seat harness to RH controller
     참고

     1x connector, Engage locking tab

     

293. Install RH lower A pillar trim
     참고

     7x clips, 4x guide tabs, 1x push clip, Align front guide tabs then align slot with harness bracket and then push rear clip to secure, Make sure all clips and tabs fully seated

     

     

     

     

294. Install RH IP end cap
     참고

     5x clips, 2x guide tabs, Pull the seal over end cap

     

     

     

295. Install RH front primary door seal
     참고

     Verify seal is seated properly on all trim panels

     

     

296. Install LH front seat into vehicle
     참고

     Recommend assistance, Install seat from front LH door opening, Assistant should be ready to support seat back once it is in the vehicle, Caution not to damage any trim

     

     

     

297. Secure LH front seat harness under LH front cabin carpet

     

298. Install clips securing LH seat harness to sill trim
     참고

     4x clips, Tuck excess harness between harness bracket and body

     

     

299. Connect LH front seat harness connector to LH controller
     참고

     1x connector, Engage locking tab

     

     

300. Install LH lower A pillar trim
     참고

     7x clips, 4x guide tabs, 1x push clip, Align guide tabs with body and harness bracket then push downwards to secure

     

     

     

301. Install LH IP end cap
     참고

     5x clips, 2x guide tabs

     

     

302. Partially install LH front primary door seal
     참고

     Verify seal is seated properly on all trim panels

     

     

303. Install LH 2nd row seat to vehicle
     참고

     Recommend assistance

     

     

304. Connect LH 2nd row seat connector
     참고

     1x connector, 1x clip, Partily lift seat assembly, Engage red locking tab

     

     

305. Connect first responder loop and LV battery
     참고

     2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

     

     

     

     

     

     

306. Install HEPA filter assembly
     참고

     2x bolts, 10mm, 10 Nm, Pivot forward edge down past frunk assembly, Then carefully move rear edge past brake reservoir and into position, Gently press on RH side of filter to seat seal onto duct, Do not pinch washer hose inbetween HEPA filter assembly and body

     

     

     

     

     

     

307. Install rear apron
     참고

     16x trim clips, 3x locator pins, 2x clips, Replace any missing or damaged clips, Ensure pyrotechnic hood actuators are aligned with openings in apron

     

     

     

308. Close hood

     

     

309. Move RH 2nd row seat to original position

     

310. Move LH 2nd row seat backward
     참고

     Adjust seat back if needed to avoid contacting other parts

     

311. Install LH 2nd row seat front bolts
     참고

     2x patch bolts, TP45, 33.5 Nm, Install new patch bolts

     

312. Move LH 2nd row seat forward
     참고

     Adjust seat back if needed

     

313. Install LH 2nd row seat rear bolts
     참고

     2x patch bolts, TP45, 33.5 Nm, Install new patch bolts

     

314. Move LH 2nd row seat to original position

     

315. Move RH front seat backward

     

316. Install RH front seat front bolts
     참고

     2x patch bolts, TP45, 33.5 Nm, Install new patch bolts

     

317. Move RH front seat forward
     참고

     Adjust seatback if needed to avoid contacting headliner

     

318. Install RH front seat rear bolts
     참고

     2x patch bolts, TP45, 33.5 Nm, Install new patch bolts

     

319. Install seat belt retractor to RH front seat pre tensioner
     참고

     Insert retractor into seat pre tensioner, Make sure it locks into position with push-pull-push test

     

     

320. Move RH front seat to original position

     

321. Move LH front seat backward

     

322. Install LH front seat front bolts
     참고

     2x patch bolts, TP45, 33.5 Nm, Install new patch bolts

     

323. Move LH front seat forward
     참고

     Adjust seat back if needed to avoid contacting headliner

     

324. Install LH front seat rear bolts
     참고

     2x patch bolts, TP45, 33.5 Nm, Install new patch bolts

     

325. Install seat belt retractor to LH front seat pre tensioner
     참고

     Insert retractor into seat pre tensioner, Make sure it locks into position with push-pull-push test

     

     

326. Move LH front seat to original position

     

327. ODIN 루틴 실행
328. ODIN 루틴 실행 PROC_EPB_X_SERVICE-MODEvia Service Mode:
     • Chassis ➜ Brakes ➜ EPB Service Mode
     • Chassis ➜ Brakes ➜ EPB Service Mode
     via Service Mode Plus:Drive Unit ➜ Rear Drive Unit Replacement ➜ Release / Re-Engage Emergency Parking Brakevia Toolbox:(link)
329. Remove wheel chocks

     

330. ODIN 루틴 실행 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
331. Raise all four window

     

332. Close all four doors
     참고

     Unlatch doors before closing if necessary