2025-06-27

Brake Lines - Master Cylinder To HCU (RHD) (Remove and Replace)

교정 코드 3303010402 FRT 1.56 바고: 절차에서 명시적으로 언급하지 않는 한 위 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간을 참조하십시오. FRT 값에 대한 피드백을 제공하려면 ServiceManualFeedback@tesla.com으로 이메일을 보내십시오. 참고: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오.참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
브레이크 오일은 페인트를 녹입니다. 도장면에 유출된 브레이크 오일을 닦을 수 있도록 깨끗한 수건과 다량의 물을 준비해 두십시오.
Informational PurposesAn informational icon, calling your attention
참고
사용한 브레이크 오일은 현지 환경 규정에 따라 폐기합니다.

탈거

  1. Put the vehicle on a 2-post lift.
    Informational PurposesAn informational icon, calling your attention
    TIp
    Ensure the vehicle is not charging.
  2. Open the RH front door and lower the window.
  3. Remove the HEPA filter assembly. See HEPA Filter Assembly (Remove and Replace).
  4. Remove the underhood storage unit. See 후드 내 보관 유닛(탈거 및 교체).
  5. Disconnect LV power. See LV Power (Disconnect and Connect) (Modify).
  6. Remove the bolt and clips (x2) that attach the air intake duct, and then remove the air intake duct from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Gently pry pin out from the thermal beam then remove the duct from the bulkhead studs.
  7. Remove the LH and RH front wheels. See 휠 어셈블리(탈거 및 장착).
  8. Remove the front aero shield panel. See Aero Shield - Front (Remove and Replace).
  9. Position a fluid catcher underneath the front of the vehicle.
  10. Position a protective fender cover over the fan shroud.
  11. Disconnect the HVIL connector.
  12. Disconnect the A/C compressor logic connector.
  13. Release the clip that attaches the harness to the HV harness bracket.
  14. Remove the bolt that attaches the A/C compressor ground strap.
  15. Remove the clip that attaches the radiator inlet hose to the A/C compressor bracket.
  16. Release the retaining clips (x5) that attach the A/C compressor HV harness to the shock tower support brace.
  17. Release the clips (x4) that attach the coolant hose to the A/C compressor bracket.
  18. Remove the bolts (x2) that attach the A/C compressor and bracket to the shock tower support brace, and then move the components aside.
    Informational PurposesAn informational icon, calling your attention
    참고
    Support the A/C compressor while removing the bolts. Carefully move the A/C compressor and A/C compressor bracket towards the front of the vehicle.
  19. Disconnect the HCU connector.
  20. Release the HCU connector harness clip.
  21. Put absorbent material underneath the brake lines and brake fluid reservoir to catch any spilled fluid.
  22. Clean the area around the brake fluid reservoir cap, and then remove the brake reservoir cap.
  23. Remove the nut that attaches the master cylinder secondary brake line to the HCU.
  24. Remove the nut that attaches the master cylinder primary line to the HCU.
  25. Remove the master cylinder secondary line from the HCU.
  26. Remove the master cylinder primary line from the HCU.
  27. Release the clip that attaches the master cylinder brake lines to the rear of the HCU bracket.
  28. Release the clips (x3) that attach the master cylinder brake lines to the rear of the HCU bracket and body.
  29. Release the master cylinder brake lines from the clips, and then remove the brake lines from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    Take care not to spill brake fluid on vehicle

장착

  1. Install the master cylinder brake lines in the clips.
  2. Install the master cylinder brake lines to the rear of the HCU bracket to the body.
  3. Install the clip that attaches the master cylinder brake lines to the rear of the HCU bracket.
  4. Install the master cylinder primary brake line to the HCU.
  5. Install the master cylinder secondary brake line to the HCU.
  6. Install the nut that attaches the master cylinder primary brake line to the HCU (torque 18 Nm).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Start threading nut by hand to avoid cross threading.
  7. Install the nut that attaches the master cylinder secondary brake line to the HCU (torque 18 Nm).
    Warning IconA warning icon, calling your attention to a possibly risky situation
    경고
    Start threading nut by hand to avoid cross threading.
  8. Attach the clip that attaches the HCU harness to the HCU bracket.
  9. Connect the HCU connector.
  10. Install the bolts that attach the A/C compressor and bracket to the shock tower support brace (torque 31 Nm).
  11. Install the clips (x4) that attach the coolant hose to the A/C compressor bracket.
  12. Install the retaining clips (x5) that attach the A/C compressor HV harness to the shock tower brace.
    Informational PurposesAn informational icon, calling your attention
    참고
    Visually inspect the clips and replace any if damaged.
  13. Install the clip that attaches the radiator inlet hose to the A/C compressor bracket.
  14. Install the bolt that attaches the A/C compressor ground strap (torque 7 Nm).
  15. Install the clip that attaches the harness to the HV harness bracket.
  16. Connect the A/C compressor logic connector.
  17. Connect the HVIL connector.
  18. Connect LV power. See LV Power (Disconnect and Connect) (Modify).
  19. Remove the protective fender cover from the fan shroud.
  20. Remove the fluid catcher from underneath the vehicle.
  21. Locally connect a laptop with Toolbox 3 to the vehicle. See Toolbox 3(연결 및 연결 해제).
  22. 브레이크 오일 저장 탱크 브리더 캡 주위를 청소하고 캡을 탈거합니다.
  23. Add clean brake fluid to the full level in the bleeder reservoir.
  24. 깨끗한 브레이크 오일을 저장 탱크의 MAX 표시까지 보충합니다.
  25. Install the pressure bleeder adapter onto the vehicle brake reservoir.
  26. Connect power supply to the bleeder tool, and then turn the bleeder tool on.
  27. Set the brake bleed reservoir pressure to 30 PSI, and then attach the brake bleed reservoir to the brake bleed adapter.
  28. Bleed the inner valve of the LH front caliper.
    1. Remove the LH front caliper inner bleed valve cover, and then install the fluid catcher.
    2. Open the inner bleed valve and watch the fluid as it flows out of the caliper.
    3. In Toolbox, click on the Actions/Autodiag tab, search for "DPB Brake Fluid Change routine", and select the PROC_DPB_BRAKE-FLUID-CHANGE, click Run to start the routine.
      Informational PurposesAn informational icon, calling your attention
      참고
      This routine can be performed via the following touchscreen path: Chassis > Procedures > DPB Post Replacement > Bleed FL Caliper.
      Informational PurposesAn informational icon, calling your attention
      참고
      DPB will pressurize the brake system with impulses.
    4. Close the bleed valve when the pump stops.
    5. Make sure that the reservoir does not go empty, or that the catch bottle does not overfill.
    6. Repeat step 28.b through step 28.e until clean fluid without bubbles flows out of the caliper.
    7. Remove the fluid catcher, and then torque the LH front caliper inner bleed valve and install the inner valve cap.
      18.5 Nm (13.6 lbs-ft)
      Informational PurposesAn informational icon, calling your attention
      TIp
      다음 공구를 사용하는 것이 좋습니다.
      • 11mm 소켓
  29. Repeat 28 to bleed the inner valve of the RH front caliper.
    Informational PurposesAn informational icon, calling your attention
    참고
    To bleed the FR inner valve via the touchscreen, choose Chassis > Procedures > DPB Post Replacement > Bleed FR Caliper.
  30. Turn off and remove the pressure brake bleeder kit from the vehicle.
  31. Check the brake fluid level and top off as necessary.
  32. Install the service brake reservoir cap.
  33. Remove the absorbent material from underneath the brake booster assembly and the reservoir area.
  34. 정비 모드 또는 Toolbox를 사용하여 다음 루틴을 수행합니다(참조 항목: 0005 - 정비 모드):
    1. TEST-SELF_DPB_TMC-BRAKE-PEDAL-PRESSvia Toolbox: (link)via Service Mode Plus: chassis ➜ DPB Post Replacement ➜ Master Cylinder Stiffness Test
      Informational PurposesAn informational icon, calling your attention
      참고
    2. TEST-SELF_BRAKE_X_DPB-ESP-CORNER-STIFFNESS-TESTvia Toolbox: (link)via Service Mode Plus:
      • chassis ➜ DPB Post Replacement ➜ Corner Stiffness Test
      • chassis ➜ ESP Post Replacement ➜ Corner Stiffness Test
      Informational PurposesAn informational icon, calling your attention
      참고

      If the test fails due to leakage, identify and address the root cause of the leak.

      If the test fails due to stiffness, perform a brake fluid bleed procedure on the failed caliper.

      If the test still fails after completing the brake fluid bleed procedure on the failed caliper, proceed with the Brake Fluid Bleed/Flush (DPB) (Maintenance) Procedure.

    3. TEST-SELF_DPB_LEAKAGE-AND-AIR-MONITORINGvia Toolbox: (link)via Service Mode Plus: chassis ➜ DPB Post Replacement ➜ Leakage and Air Monitoring Test
      Informational PurposesAn informational icon, calling your attention
      참고
      If the routine fails, perform Brake Fluid Bleed/Flush (DPB) (Maintenance).
      Informational PurposesAn informational icon, calling your attention
      참고
      To perform this routine via the touchscreen: Chassis > Procedures > DPB Post Replacement > Leakage and Air Monitoring Test
  35. 브레이크 페달을 여러 번 밟아 브레이크 페달의 느낌과 동작이 적절한지 확인합니다.
  36. Exit Service Mode or disconnect the laptop if applicable (see 0005 - 정비 모드).
  37. Install the front aero shield panel. See Aero Shield - Front (Remove and Replace).
  38. Install the LH and RH front wheels. See 휠 어셈블리(탈거 및 장착).
  39. Install the air intake duct. See Duct - Air Intake (Remove and Replace).
  40. Install the HEPA filter assembly. See HEPA And Carbon Filters (Remove and Replace).
  41. Install the underhood storage unit. See 후드 내 보관 유닛(탈거 및 교체).
  42. Perform a road test to make sure there is proper pedal feel and brake performance.
    Informational PurposesAn informational icon, calling your attention
    참고
    서비스 방문에 시험 주행 교정 코드 00040100을 별도 활동으로 추가합니다.