2026-03-30

Rear Fascia Assembly (Model Y Standard) (Remove and Install)

교정 코드 10011400501 0.48 메모: 절차에서 명시적으로 언급하지 않는 한 위에 나열된 교정 코드 및 FRT는 연결된 절차를 포함하여 이 절차를 수행하는 데 필요한 모든 작업을 반영합니다. 명시적으로 지시하지 않는 한 교정 코드를 누적하지 마십시오. 참고: FRT와 그 생성 방법에 대한 자세한 내용은 표준 정비 작업시간의 내용을 참조하십시오. 메모: 아래 절차를 수행할 때 개인 보호의 내용을 참조하여 적절한 PPE를 착용했는지 확인하십시오. 참고: 안전하고 건강한 작업 사례는 인체공학적 주의 사항의 내용을 참조하십시오.

Warning IconA warning icon, calling your attention to a possibly risky situation
경고
이 절차는 초안입니다. 따라서 검증은 되었지만 경고 및 주의 사항이 누락되었을 수 있습니다. 고전압 시스템 및 구성 요소에서 또는 그 근처에서 작업하는 경우에는 안전 요구 사항을 준수하고 최고 수준의 주의를 기울여야 합니다.
  • 2026-03-16: Released new procedure.

탈거

  1. Open the LH rear door.
  2. Lower the LH rear window.
  3. Remove the LH rear fender garnish from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips, 2x tabs, Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish
  4. Remove the screw that secure the LH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, 8mm, 2 Nm
  5. Remove the LH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  6. Remove the bolt that secures the LH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, 10mm, 3.5 Nm
  7. Open the RH rear door.
  8. Lower the RH rear window.
  9. Remove the RH rear fender garnish from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips, 2x tabs Release from center of garnish and work your way outward towards both ends, Using clip prytool release clips at rear of fascia to avoid damage to garnish
  10. Remove the screw securing the RH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, 8mm, 2 Nm
  11. Remove the RH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  12. Remove the bolt that secures the RH corner of the rear fascia to the body,
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, 10mm, 3.5 Nm
  13. Remove the rear fascia diffuser front bolts (x2)
    Informational PurposesAn informational icon, calling your attention
    참고
    10mm, 5 Nm
  14. Release the rear fascia diffuser.
    Informational PurposesAn informational icon, calling your attention
    참고
    7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers
  15. Release the rear fascia assembly from the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Disengage locking tab, Recommend assistance, Place rear fascia on padded surface to avoid damage

장착

  1. Secure the rear fascia assembly onto the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x connector, Engage locking tab, Recommend assistance
  2. Secure the rear fascia diffuser.
    Informational PurposesAn informational icon, calling your attention
    참고
    7x bolts, 10mm, The five center bolts 5 Nm, both outside bolts 4 Nm, 6x push clips, 2x fastener covers, Apply Loctite 222 onto bolts
  3. Install the rear fascia diffuser front bolts.
    Informational PurposesAn informational icon, calling your attention
    참고
    2x bolts, 10mm, 5 Nm, Apply Loctite 222 onto rear aero shield bolts
  4. Install the bolt that secures the RH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, 10mm, 3.5 Nm
  5. Install the RH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  6. Install the screw that secures the RH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, 10mm, 2 Nm
  7. Install the RH rear fender garnish.
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips, 2x tabs, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
  8. Raise the RH rear window.
  9. Close the RH rear door.
  10. Install the bolt that secures the LH corner of the rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x bolt, 10mm, 3.5 Nm
  11. Install the LH tail lamp. See GUID-809F5D76-3278-4882-A1DA-DE4DD433696A.html.
  12. Install the screw that secures the LH rear fascia to the body.
    Informational PurposesAn informational icon, calling your attention
    참고
    1x screw, 8mm, 2 Nm
  13. Install the LH rear fender garnish to the vehicle.
    Informational PurposesAn informational icon, calling your attention
    참고
    11x clips, 2x tabs, Install ends of garnish into rocker panel and rear diffuser then work your way from rear towards front of garnish
  14. Return the 2nd row 60 seatback to vertical position.
    Informational PurposesAn informational icon, calling your attention
    참고
    Via trunk seat switch, Remove seatback protection if necessary
  15. Close the liftgate.
  16. Raise the LH rear window.
  17. Close the LH rear door.