23/01/2024 21:08:06

Knee Impact Foam - RH (NA) (Remove and Replace)

校正代码 1405010111 1405010112 注意:除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。 注意:请参阅平均维修工时,深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈,请发送电子邮件至LaborTimeFeedback@tesla.com 注意:请参阅人员保护,确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。

Warning IconA warning icon, calling your attention to a possibly risky situation
警告
尽管此程序已经过验证,但仍是一个草案。可能没有警告和注意事项。请遵守安全要求,处理或靠近高压系统和部件时,请谨慎操作。请将校正修理内容及反馈发送至ServiceDevelopment@teslamotors.com
  1. Open LH front door
  2. Lower LH front window
  3. Move LH front seat backward
  4. Open hood
  5. Remove rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    14x clips
  6. Power off vehicle from center display
    Informational PurposesAn informational icon, calling your attention
    Via Controls > Safety > Power Off, Select Power Off button at warning dialogue box
  7. Disconnect LV battery and First Responder Loop
    Informational PurposesAn informational icon, calling your attention
    2x connectors, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge
  8. Partially release LH front primary door seal
    Informational PurposesAn informational icon, calling your attention
    Release lower section of LH front primary door seal
  9. Remove LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    5x clips, 2x guide tabs
  10. Release LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    2x magnets,1x guide tab
  11. Remove connectors from LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    1x connector, 1x OBDII connector, Release OBDII connector by depressing tabs from front side
  12. Remove LH knee airbag bolt covers
    Informational PurposesAn informational icon, calling your attention
    2x covers
  13. Remove LH knee air bag bolts
    Informational PurposesAn informational icon, calling your attention
    4x bolts, EP10, 8.5 Nm, Discard bolts after removal
  14. Remove LH knee airbag assembly
    Informational PurposesAn informational icon, calling your attention
    1x connector, Peel back plastic film, Release by pulling back both white tabs simultaneously, Avoid straining harness, Only one tab visible in image matching tab is on opposite side
  15. Remove screws securing IP lower assembly to IP carrier
    Informational PurposesAn informational icon, calling your attention
    1x screw, T20, 2.3 Nm
  16. Remove IP lower assembly from IP carrier
    Informational PurposesAn informational icon, calling your attention
    13x tabs
  17. Remove screws securing IP carrier to cross car beam on lower LH side
    Informational PurposesAn informational icon, calling your attention
    3x screws, T20, 2.3 Nm, 2x datums
  18. Remove screws securing IP carrier to cross car beam at lower center
    Informational PurposesAn informational icon, calling your attention
    3x screws, T20, 2.3 Nm, 3x datums
  19. Remove RH Knee Impact Foam
    Informational PurposesAn informational icon, calling your attention
    Carefully pull the IP carrier outwards to remove RH Knee Impact Foam
  20. Install RH Knee Impact Foam
    Informational PurposesAn informational icon, calling your attention
    Carefully pull the IP carrier outwards to install RH Knee Impact Foam
  21. Install screws securing IP carrier to cross car beam at lower center
    Informational PurposesAn informational icon, calling your attention
    3x screws, T20, 2.3 Nm, 3x datums
  22. Install screws securing IP carrier to cross car beam on lower LH side
    Informational PurposesAn informational icon, calling your attention
    3x screws, T20, 2.3 Nm, 2x datums
  23. Install IP lower assembly to IP carrier
    Informational PurposesAn informational icon, calling your attention
    13x tabs
  24. Install screws securing IP lower assembly to IP carrier
    Informational PurposesAn informational icon, calling your attention
    1x screw, T20, 2.3 Nm
  25. Install LH knee airbag assembly
    Informational PurposesAn informational icon, calling your attention
    1x connector, Ensure airbag connector is fully engaged, Apply knee airbag label over squib assembly
  26. Install LH knee air bag bolts
    Informational PurposesAn informational icon, calling your attention
    4x bolts, EP10, 8.5 Nm, Install new bolts
  27. Install LH knee airbag bolt covers
    Informational PurposesAn informational icon, calling your attention
    2x covers
  28. Install connectors to LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    1x connector, 1x OBDII connector, Ensure tabs engage on OBDII connector
  29. Install LH footwell cover
    Informational PurposesAn informational icon, calling your attention
    2x magnets,1x guide tab
  30. Install LH IP end cap
    Informational PurposesAn informational icon, calling your attention
    5x clips, 2x guide tabs
  31. Install LH front primary seal
    Informational PurposesAn informational icon, calling your attention
    Verify seal is seated properly on all trim panels
  32. Connect First Responder Loop and LV battery
    Informational PurposesAn informational icon, calling your attention
    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
  33. Install rear underhood apron
    Informational PurposesAn informational icon, calling your attention
    14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
  34. Close hood
  35. Move LH front seat to original position
  36. Raise LH front window
  37. Close LH front door