2026-07-31

同轴电缆 - 侧转向灯 - 前 - 左右两侧（更换） ((拆卸和更换))

校正代码 17403032 2.88 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
  • 2026-07-09: Released new procedure.

Overlay

  1. Raise and support vehicle
    注
    Ensure vehicle is not charging
  2. Open LH front door
  3. Lower LH front window
  4. Open RH front door
  5. Lower RH front window
  6. Move RH front seat backward
  7. Remove the wiper module. See 前雨刮模块（左驾驶） ((拆卸和更换)).
  8. Remove fresh air intake assembly
    注
    2x studs, Lift cowl as needed
  9. Remove RH front wheel center cap
    注
    1x cap, Pull the inner side of the adjacent 2 claws on the wheel center cap by hands
  10. Loosen RH front wheel nuts
    注
    5x nuts, 21mm, 175 Nm
  11. Remove LH front wheel center cap
    注
    1x cap, Pull the inner side of the adjacent 2 claws on the wheel center cap by hands
  12. Loosen LH front wheel nuts
    注
    5x nuts, 21mm, 175 Nm
  13. Raise vehicle partially and lower lift onto locks
    注
    Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, Otherwise vehicle may tilt to the side
  14. Remove RH front wheel
    注
    5x nuts, 21mm, 175 Nm
  15. Partially remove RH front wheel liner
    注
    8x clips, 1x bolt, 10mm, 5 Nm
  16. Disconnect the front harness connectors for the RH side repeater and camera
    注
    2x connectors, Release locking tabs
  17. Remove LH front wheel
    注
    5x nuts, 21mm, 175 Nm
  18. Partially remove LH front wheel liner
    注
    8x clips, 1x bolt, 10mm, 5 Nm
  19. Disconnect the front harness connectors for the LH side repeater and camera
    注
    2x connectors, Release locking tabs
  20. Lower vehicle partially and set lift onto locks
    注
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
  21. Power off vehicle from center display
    注
    Via Controls > Safety > Power Off, Select Power Off button at warning dialog box
  22. Disconnect LV battery and first responder loop
    注
    2x connectors, Ensure that one minute has passed after window movement before performing the power-off, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge
  23. Disconnect thermal sub-harness from front controller
    注
    1x connector, Depress locking tab and rotate to release
  24. Remove bolts securing front controller shield assembly and remove from vehicle
    注
    2x bolts, 10mm, 8.5 Nm
  25. Disconnect front controller harness connectors
    注
    5x connectors, 1x harness guide, Release locking tab if equipped
  26. Remove bolt securing ground cable to front controller
    注
    1x bolt, 10mm, 8.5 Nm,
  27. Remove bolts securing front controller
    注
    3x bolts, 10mm, 10 Nm
  28. Tilt front controller forward for access
    注
    Lift cowl screen up appropriately
  29. Release LV negative harness clip from front controller
    注
    1x clip
  30. Remove front controller from vehicle
    注
    1x tab
  31. Release RH footwell cover
    注
    2x magnets, 1x guide tab, 1x connector
  32. Partially release RH front primary door seal
    注
    Release lower section of RH front primary door seal
  33. Remove RH IP end cap
    注
    5x clips, 2x guide tabs
  34. Remove RH lower A-pillar trim
    注
    4x clips, 2x guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet
  35. Remove RH knee airbag bolt covers
    注
    2x covers
  36. Remove RH knee airbag bolts
    注
    4x bolts, EP10, 8.5 Nm, Discard bolts after removal, brake loose e10 by hand then use e-ratchet to back off hardware
  37. Remove RH knee air bag assembly
    注
    1x air bag connector, 1x connector, Peel back plastic film, Release by pulling back both white tabs simutaneously, Avoid straining harness, Only one tab visible in image matching tab is on opposite side
  38. Remove clips securing passenger footwell duct
    注
    2x clips
  39. Disconnect glove box USB cable connector from car computer
    注
    1x connector, Release locking tab then release connector
  40. Remove screws securing glove box to IP
    注
    4x screws, T20, 2.3 Nm
  41. Release glove box from IP assembly
    注
    10x clips, 3x locator pins, 1x datum, Avoid damage to electromagnetic switch
  42. Remove glove box
    注
    2x connectors
  43. Remove RH passenger footwell duct from HVAC module
  44. Disconnect RH IP air wave duct thermistor connector
    注
    1x connector
  45. Remove RH IP air wave duct from HVAC module
  46. Unfold RH front main cabin carpet back to original position
    注
    1x locator clip
  47. Release windshield heater connecter
    注
    1x connector
  48. Release RH grommet from body
  49. Remove electrical tape securing harness bundle to rubber dust boot
    注
    Use a razor blaze, carefully cut electrical tape away to expose rubber dust boot
  50. Remove locking pin from connector
    注
    Carefully pry pin out of connector and fully remove locking pin
  51. Remove coax cable needed for the side repeater overlay terminal 2 (LHS)
    注
    Inspect all components for damage
  52. Remove coax cable needed for the side repeater overlay terminal 1 (RHS)
    注
    Inspect all components for damage
  53. Apply harness tape onto LH coax overlay cable before installation
    注
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  54. Apply harness tape onto RH coax overlay cable before installation
    注
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle
  55. Release frunk harness cover
    注
    3x tabs
  56. Position M3 LH coax overlay cable into place, Place through LH wheel liner
    注
    Pull till you have roughly 12 inches of cable towards the interior of the vehicle
  57. Pull LH coax overlay cable through frunk harness
    注
    Pull harness towards car computer, Route under brake booster lower connector
  58. Tape coax overlay onto fish nylon tape
  59. Release frunk harness cover
    注
    3x tabs
  60. Position M3 LH coax overlay cable into place, Place through LH wheel liner
    注
    Pull till you have roughly 12 inches of cable towards the interior of the vehicle
  61. Pull LH coax overlay cable through frunk harness
    注
    Pull harness towards car computer, Route under brake booster lower connector
  62. Tape coax overlay onto fish nylon tape
  63. Pull LH coax overlay cable through bulkhead and into interior cabin
  64. Remove nylon fish tape
    注
    Remove tape the pull nylon fish tape out of vehicle
  65. Pull RH coax overlay cable through RH grommet harness
    注
    Pull harness toward car computer under RH grommet main harness
  66. Position RH coax overlay cable into place, Place through RH wheel liner
    注
    Pull till you have roughly 6 inches of cable towards the interior of the vehicle
  67. Tape coax overlay onto fish nylon tape
  68. Pull RH coax overlay cable through bulkhead and into interior cabin
  69. Remove nylon fish tape
    注
    Remove tape the pull nylon fish tape out of vehicle
  70. Disconnect side repeater cameras connector from car computer
    注
    1x locking connector
  71. Remove locking pin from side repeater cameras connector
    注
    Carefully pry pin out of connector and fully remove locking pin
  72. Remove coax terminal 2 (LHS) cable from connector
    注
    Inspect all components for damage
  73. Remove coax terminal 1 (RHS) cable from connector
    注
    Inspect all components for damage
  74. Insert new side repeater coax terminal 1 (RHS) cable onto side repeater cameras connector
    注
    Ensure both coax cables are fully seated into connector, Audible locking and flush mounting to confirm
  75. Insert new side repeater coax terminal 2 (LHS) cable onto side repeater cameras connector
    注
    Ensure both coax cables are fully seated into connector, Audible locking and flush mounting to confirm
  76. Secure locking pin to connector
    注
    Align tabs of lock in connector housing, Ensure flush installation of locking pin to connector housing
  77. Connect side repeater cameras connector onto car computer
    注
    1x locking connector
  78. Position LH coax overlay cable onto frunk main harness, Secure cable onto harness using zip ties
    注
    7x zip-ties, Trim off excess material after harness has been secured
  79. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    注
    Cut the coax connector only
  80. Connect front harness connectors for LH side repeater and camera
    注
    2x connectors, Secure locking tabs
  81. Position RH coax overlay cable onto frunk main harness grommet, Secure cable onto harness using zip ties
    注
    3x zip-ties, Trim off excess material after harness has been secured
  82. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    注
    Cut the coax connector only
  83. Connect front harness connectors for the RH side repeater and camera
    注
    2x connectors, Secure locking tabs
  84. Secure RH grommet from body
    注
    Use electrical tape to wrap the end of the dust boot
  85. Secure frunk harness cover
    注
    3x tabs
  86. Secure windshield heater connector
    注
    1x connector
  87. Install LH front wheel liner to vehicle
    注
    8x clips, 1x bolt, 10mm, 5 Nm
  88. Install LH front wheel
    注
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  89. Install RH front wheel liner to vehicle
    注
    8x clips, 1x bolt, 10mm, 5 Nm
  90. Install RH front wheel
    注
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool, Torque at later step
  91. Lower vehicle until tires are touching ground
    注
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  92. Torque LH front wheel
    注
    5x nuts, 21mm, 175 Nm
  93. Install LH front wheel center cap
    注
    1x cap, Ensure that the cap is installed in place
  94. Torque RH front wheel
    注
    5x nuts, 21mm, 175 Nm
  95. Install RH front wheel center cap
    注
    1x cap, Ensure that the cap is installed in place
  96. Place front controller into vehicle for installation
    注
    1x tab
  97. Secure LV negative harness clip from front controller
    注
    1x clip
  98. Tilt front controller backward for installation
    注
    Lift cowl screen up appropriately
  99. Install bolts securing front controller
    注
    3x bolts, 10mm, 10 Nm
  100. Install bolt securing ground cable to front controller
    注
    1x bolt, 10mm, 8.5 Nm,
  101. Connect front controller harness connectors
    注
    5x connectors, 1x harness guide, Secure locking tab, if equipped
  102. Install front controller shield to front controller
    注
    2x bolts, 10mm, 8.5 Nm
  103. Connect thermal sub-harness to front controller
    注
    1x connector, Rotate fully to secure locking tab
  104. Install the wiper module. See 前雨刮模块（左驾驶） ((拆卸和更换)).
  105. Install fresh air intake assembly
    注
    2x studs, Lift cowl as needed
  106. Position frunk assembly to vehicle
    注
    8x clips, 3x locator pins, Ensure clips are aligned at thermal beam, Replace any clips if broken or missing
  107. Install bolts securing frunk assembly
    注
    4x bolts, 10mm, 5 Nm, Number of bolts may vary depending on build date
  108. Install access panel to frunk assembly
    注
    3x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push forward to secure clips
  109. Install fresh air gutter assembly
    注
    3x clips
  110. Install RH IP air wave duct to HVAC module
  111. Install clips securing RH IP air wave duct
    注
    2x push clips
  112. Connect thermistor connector RH IP air wave duct
    注
    1x connector
  113. Install RH passenger footwell duct to HVAC module
  114. Position glove box assembly
    注
    2x connectors
  115. Install glove box into IP assembly
    注
    10x clips, 3x locator pin, 1x datum, If necessary, Replace any clips that are broken
  116. Install screws securing glove box assembly to IP assembly
    注
    4x screws, T20, 2.3 Nm
  117. Connect glove box USB cable to car computer
    注
    1x connector, Engage locking tab
  118. Install clips securing passenger footwell duct
    注
    2x push clips, Ensure that the footwell duct is installed in place
  119. Install RH IP end cap
    注
    5x clips, 2x guide tabs
  120. lnstall seat lower section of RH front primary seal
    注
    Verify seal is seated properly on all trim panels
  121. Install RH knee air bag assembly
    注
    1x air bag connector, 1x connector, Ensure airbag connector is fully engaged, Place plastic film back over squib assembly
  122. Install RH knee airbag bolts
    注
    4x bolts, EP10, 8.5 Nm, use socket wrench to start hardware by hand to avoid cross threading. Avoid Over tightening Hardware during installation avoid using power tools
  123. Install RH knee air bag bolt covers
    注
    2x covers
  124. Install RH footwell cover
    注
    2x magnets, 1x guide tab, 1x connector
  125. Connect first responder loop and LV battery
    注
    2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated
  126. Install rear apron
    注
    14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
  127. Close hood
  128. Move RH front seat to original position
  129. Raise RH front window
  130. Close RH front door
  131. Verify operation of windshield washers and wipers
  132. Clear DAS Calibration through UI
    注
    Controls > Service > Camera Calibration, Select Clear Calibration, Verify calibration was cleared successfully, Wait for prompt to disappear automatically before continuing, Calibration in Progress message and progress icon will appear during the next drive cycle
  133. Raise LH front window
  134. Close LH front door
  135. Remove lift arms from below vehicle
    注
    Lower rack arms fully and remove them from under vehicle
  136. Vehicle will need to be driven by customer to complete calibration procedure. During this time DAS functions will be completely unavailable