2026-08-09

线束 - 车身 - 右侧（左驾驶） ((拆卸和更换))

校正代码 1710040042 2.46 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

  • 2026-04-13: Updated the specs of the bolt securing the RH retractor to the base of B-pillar from 15 mm to 13 mm.

拆卸

  1. Open all four doors
    注
    If vehicle is being powered down, Latch rear doors to prevent accidental closure
  2. Open trunk from exterior switch
  3. Lower all four windows.
  4. Place vehicle into tow mode
    注
    Via Controls > Service > ''Towing''
  5. Place wheel chocks to keep vehicle from moving
  6. Disconnect the LV battery power. See 低压电源 - 锂离子（断开和连接）.
  7. Remove RH IP end cap
    注
    5x clips, 2x guide tabs
  8. Release RH footwell cover
    注
    2x magnets, 1x guide tab, 1x connector
  9. Remove connectors from RH footwell cover
    注
    1x puddle light connector, 1x Speaker connector
  10. Remove clips securing passenger footwell duct
    注
    2x clips
  11. Disconnect glove box USB cable from car computer
    注
    1x connector, Release locking tab then release connector
  12. Remove screws securing glove box to IP
    注
    4x screws, T20, 2.3 Nm
  13. Release glove box from IP carrier
    注
    10x clips, 3x locator pins, 1x datum, Avoid damage to electromagnetic switch
  14. Disconnect the glove box connectors (x2).
  15. Remove RH passenger footwell duct from HVAC module
  16. Remove RH upper A-pillar trim
    注
    6x clips, 1x tether, 2x guide tabs,1x alignment pin, Pull inside of the upper portion of upper A-pillar, Depress 2x tabs to remove tether from body side, Then pull upper A-pillar upward to remove
  17. Remove RH sun visor bracket cover
    注
    4x clips, Extending the sun visor may allow for extra working room
  18. Remove RH sun visor fastener
    注
    1x screw, T25, 3.5 Nm, Extending the sun visor may allow for extra working room
  19. Remove RH sun visor from headliner area
    注
    Fold sun visor to the closed and folded down position but do not latch in place
  20. Disconnect RH sun visor connector
    注
    1x connector
  21. Remove clip for RH lower A-pillar trim
    注
    1x push clip
  22. Remove RH lower A-pillar trim
    注
    4x clips, 2x guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet
  23. Remove RH side rail assembly
    注
    4x clips, 2x locations, 4x tethers, Pull the upper corner of the side rail then work your way to bottom, Pull the lower side rail toward RH to release clips, Release tethers from bolted bungee tether
  24. Remove tether hooks from RH body
    注
    2x tether hooks, Discard after removal
  25. Push open RH coat hook
  26. Pry open RH coat hook screw cover
    注
    2x clips
  27. Remove RH coat hook screw
    注
    1x screw, T25, 2.5 Nm
  28. Release 2nd row seat cushion and disconnect harness
    注
    2x clips, 2x connectors, Press tabs backward then pull front edge up
  29. Fold 2nd row 40 seatback down
  30. Remove RH side bolster
    注
    1x locator clip, 3x guide tabs, Pull outward then slightly upward to remove
  31. Remove bolster plastic bracket from RH side body
    注
    2x clips, If necessary, depress the clips from behind, this bracket may come out with bolster. Discard after removal
  32. Remove RH C pillar assembly and move it aside
    注
    3x clips, 3x tabs, Pull rear C-pillar inward then forward to remove
  33. Remove RH lower B-pillar assembly
    注
    7x clips, 5x locator clips, Pull the trim panel outward in the direction of the arrow to release clip from lower B-pillar
  34. Remove RH middle B-pillar assembly
    注
    5x clips, 3x locator clips, Pull the bottom of the B-pillar middle trim panel into the vehicle, and then pull the upper part to release the remaining clips
  35. Release clips securing RH upper B-pillar assembly and move aside
    注
    3x clips,3x locator pins,Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips
  36. Remove LH side rail assembly
    注
    4x clips, 2x locations, 4x tethers, Pull the upper corner of the side rail then work your way to bottom, Pull the lower side rail toward RH to release clips, Release tethers from bolted bungee tether
  37. Remove tether hooks from LH body
    注
    2x tether hooks, Discard after removal
  38. Push open LH coat hook
  39. Pry open LH coat hook screw cover
    注
    2x clips
  40. Remove LH coat hook screw
    注
    1x screw, T25, 2.5 Nm
  41. Fold 2nd row 60 seatback down
    注
    Pull release, Fold down, Protect the seat cushion if necessary
  42. Remove LH side bolster
    注
    1x locator clip, 3x guide tabs, Pull outward then slightly upward to remove
  43. Remove bolster plastic bracket from LH side body
    注
    2x clips, If necessary, depress the clips from behind, this bracket may come out with bolster. Discard after removal
  44. Remove LH C pillar assembly and move it aside
    注
    3x clips, 3x tabs, Pull rear C-pillar inward then forward to remove
  45. Remove LH IP end cap
    注
    5x clips, 2x guide tabs
  46. Remove clip securing LH lower A-pillar assembly
    注
    1x push clip
  47. Remove LH lower A-pillar assembly
    注
    4x clips, 2x guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet
  48. Remove LH lower B-pillar assembly
    注
    7x clips, 4x locator clips, Pull the trim panel outward in the direction of the arrow to release clip from lower B-pillar
  49. Remove LH middle B-pillar assembly
    注
    5x clips, 3x locator clips, Pull the bottom of the B-pillar middle trim panel into the vehicle, and then pull the upper part to release the remaining clips
  50. Release clips securing the LH upper B-pillar assembly and move aside
    注
    3x clips,3x locator pins,Pull the bottom of the upper B-pillar toward inside of the car, then pull the top to release the remaining clips
  51. Release rear headliner from body
    注
    4x clips, 2x locator pins,loosen the rear of the headliner to facilitate the next step
  52. Remove package tray harness clips around C-pillar area
    注
    2x clips
  53. Disconnect package tray harness connector from RH body harness
    注
    1x connector
  54. Remove package tray
    注
    5x tabs, 3 at the rear of panel and 2 on the sides, Slide towards front of vehicle to remove
  55. Remove load floor
    注
    Use pull tab located at rear edge of panel
  56. Remove trunk sill trim assembly
    注
    4x clips, Pull corner upward to release clip on end then pull away from body for remaining clips
  57. Remove RH load floor bracket
    注
    4x clips, 2x locations, Release bracket front clips, then release clips at the bracket rear, and remove the floor bracket
  58. Remove trunk garnish assembly
    注
    6x clips, 4x locating tabs
  59. Remove clips for RH trunk side trim
    注
    2x clips
  60. Disconnect RH trunk task light connector
    注
    1x connector
  61. Remove RH trunk side trim
  62. Release harness connectors on left side of car computer
    注
    3x connectors, Release locking tab, then remove connector body
  63. Release harness clips from left of car computer
    注
    1x clips
  64. Release harness clips from lower of car computer
    注
    2x clips
  65. Disconnect connectors from car computer
    注
    4x connector
  66. Release RH body harness from RH body controller and A-pillar and move aside
    注
    3x clips
  67. Remove the bolt securing the RH body controller to vehicle
    注
    1x nyloc nut, 10mm, 6 Nm
  68. Remove RH body controller from vehicle
    注
    Move RH controller up and away from the vehicle body for easier access to the connector in the next step
  69. Disconnect J2 connector from RH body controller
    注
    1x connector, 1x locking tab, J2
  70. Disconnect J5 connector from RH body controller
    注
    1x connector, J5
  71. Disconnect J4 connector from RH body controller
    注
    1x connector, 1x locking tab, J4
  72. Disconnect J12 connector from RH body controller
    注
    1x connector, J12
  73. Disconnect seat connector from RH body controller
    注
    1x connector, 1x locking tab, J9
  74. Disconnect connector from the right body harness
    注
    1x connector
  75. Fold RH front main cabin carpet aside for access
    注
    1x clip
  76. Release harness clip from RH body controller
    注
    1x clip
  77. Disconnect connectors from harness clip at RH lower A-pillar area
    注
    3x connectors
  78. Disconnect DCDC positive cable from right body harness
    注
    1x connector, 1x clip. Pull up the red locking tab and then press
  79. Release the LH front seat harness from sill trim clips (x5).
  80. Disconnect LH harness connectors around RH lower B-pillar area
    注
    3x connectors
  81. Remove fixed harness connector bracket from RH b pillar area
    注
    1x connector bracket
  82. Remove bolt securing RH retractor to base of B-pillar
    注
    1x patch bolt, 13mm, 40 Nm, Discard patch bolt
  83. Disconnect harness connectors from RH retractor
    注
    2x connectors, 2 stage locking connectors, Lift the red tab to release the connector Disconnect connector after removing retractor from B-pillar
  84. Remove RH B-pillar impact accelerometer sensor
    注
    1x connector
  85. Disconnect RH body wiring harness and RH rear door wiring harness connectors from RH B-pillar area
    注
    1x connector
  86. Remove RH body harness clips from B-pillar area
    注
    3x clips
  87. Remove clip securing RH rear carpet of vehicle to body
    注
    1x clip
  88. Remove RH body harness ground strap around lower B-pillar
    注
    1x bolt, 10mm, 10 Nm
  89. Release RH body harness clips along RH front sill area
    注
    1x clip
  90. Remove RH B-pillar applique fasteners cover
    注
    4x clips, 1x tab, Release upper clips first, then slide tab out of body
  91. Remove bolts securing RH B-pillar applique to body
    注
    2x bolts, 8mm, 5 Nm
  92. Release RH B-pillar applique from vehicle
    注
    1x clip, 2x tabs, Release the bottom of the applique and slide the applique downward to remove, Use caution not to damage the connectors
  93. Disconnect B-pillar camera and RH antenna connector
    注
    2x connectors, Release red locking tab first before removing connector
  94. Release RH upper B-pillar bracket form body
    注
    2x bolts 10mm2.5 Nm
  95. Remove the RH body harness clips from B-pillar area
    注
    7x clips
  96. Disconnect RH body harness to the TCU connector
    注
    2x connector
  97. Disconnect HVC logic connector and install logic cap
    注
    1x connector, 1x cap, Release locking tab then push the handle downward to release connector
  98. Release positive LV output cover from PCS cable
    注
    1x cover
  99. Remove nut securing positive LV output from PCS cable and move cable aside
    注
    1x nut, 13mm, 15 Nm, Discard after removal
  100. Disconnect 40 seat back heater harness
    注
    1x connector
  101. Disconnect RH rear seat belt buckle connector
    注
    1x connector
  102. Remove clip securing RH rear seatbelt buckle harness to vehicle body
    注
    2x clips
  103. Remove RH body harness clips around lower C-pillar area
    注
    6x clips
  104. Disconnect RH 2nd row seat belt retractor connector
    注
    1x connector, 2 stage locking connectors, Lift the red tab to release the connector
  105. Disconnect harness connector for RH side curtain airbag
    注
    1x connector, 2 stage locking connectors, Lift the white tab to release the connector
  106. Disconnect RH antenna filter harness connector
    注
    1x connector. Gently disconnect the harness. Do not damage the heater grid
  107. Release the trunk harness connectors under package tray area
    注
    2x connectors
  108. Release trunk harness connectors bracket under package tray area
    注
    2x connector bracket
  109. Disconnect LH and RH parcel shelf speaker connectors
    注
    2x connector
  110. Remove the RH body harness clips around the upper C-pillar area
    注
    10x clips
  111. Disconnect RH power strut connector
    注
    1x connector
  112. Remove ground strap of body harness in RH area of the trunk
    注
    1x bolt, 10mm, 10 Nm
  113. Remove RH body harness clips around RH side of trunk area
    注
    1x connector bracket3x harness clips
  114. Disconnect connector from RH rear audio amplifier
    注
    3x connectors
  115. Remove wheel chocks
  116. Push vehicle onto lift
    注
    Recommend assistance, Note this vehicle can only be safely pushed for a very short distance and at very slow speed
  117. Raise and support the vehicle. See 举升车辆 - 双柱举升机.
  118. Loosen RH rear wheel
    注
    5x nuts, 21mm, 175 Nm
  119. Raise vehicle partially and lower lift onto locks
    注
    Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  120. Remove RH rear wheel
    注
    5x nuts, 21mm, 175 Nm
  121. Remove clips securing the RH rear wheel liner to body
    注
    8x push clips, 7x fan clips
  122. Remove RH rear wheel liner
  123. Disconnect RH side subframe harness connector
    注
    1x connector, Release locking tab
  124. Disconnect RH rear EBP harness from rear main body harness
    注
    1x connector, Release locking tab
  125. Remove RH body harness clips around RH subwoofer area
    注
    2x harness clips2x connector bracket
  126. Lower vehicle partially and set lift onto locks
    注
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
  127. Push grommet through RH side trunk bulkhead and feed harness through
    注
    1x grommet, Bulkhead around rear portion RH wheel liner area
  128. Remove RH body wiring harness from vehicle

安装

  1. Position RH body harness to vehicle for installation
    注
    Layout the position and direction of the new wiring harness on the vehicle for installation
  2. Push rear subframe portion of RH body harness through RH side trunk bulkhead
    注
    Check if the seal is in place after installation
  3. Install RH body harness clips around RH subwoofer area
    注
    2x harness clips2x connector bracket
  4. Connect RH rear EPB harness to rear main body harness
    注
    1x connector, Engage locking tab
  5. Connect RH side subframe harness connector
    注
    1x connector
  6. Raise the vehicle to a comfortable working height, and lower the lift onto locks.
    警告

    Make sure there is an audible click of the locks on both sides before lowering, otherwise the vehicle may tilt to one side.

    Make sure that the doors are clear of surrounding objects.

  7. Position the RH rear wheel liner for installation
  8. Install the clips securing RH rear wheel liner
    注
    8x push clips, 7x fan clips
  9. Install RH rear wheel
    注
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  10. Lower vehicle fully
    注
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  11. Remove lift arms from below vehicle
    注
    Lower rack arms fully and remove them from under vehicle
  12. Torque RH rear wheel
    注
    5x nuts, 21mm, 175 Nm
  13. Push vehicle away from lift
    注
    Recommend assistance, Note this vehicle can only be safely pushed for a very short distance and at very slow speed, Chock wheels.
  14. Place wheel chocks to keep vehicle from moving
  15. Connect connector on rear RH audio amplifier
    注
    3x connectors
  16. Install RH body harness clips around RH side of trunk area
    注
    1x connector bracket3x harness clips
  17. Install ground strap of body harness in RH area of the trunk
    注
    1x bolt, 10mm, 10 Nm
  18. Connect RH power strut connector
    注
    1x connector
  19. Install RH body harness clips around the upper C-pillar area
    注
    10x clips
  20. Connect LH and RH parcel shelf speaker
    注
    2x connectors
  21. Install trunk harness connectors bracket under package tray area
    注
    2x connector bracket
  22. Connect the trunk harness connectors under package tray area
    注
    2x connectors
  23. Connect RH antenna filter harness connector to RH connector to antenna grid
  24. Connect harness connector for RH side curtain airbag
    注
    1x connector,Press the connector. When the connector is fully seated, you will hear the click sound of the secondary locking pin returning
  25. Connect RH 2nd row seat belt retractor connector
    注
    1x connector, 2 stage locking connectors, Press the connector. When the connector is fully seated, you will hear the click sound of the secondary locking pin returning
  26. Install RH body harness clips around lower C-pillar area
    注
    6x clips
  27. Secure RH rear right seatbelt buckle harness to vehicle body
    注
    2x clips
  28. Connect RH rear seat belt buckle connector
    注
    1x connector
  29. Connect 40 seat back heater harness
    注
    1x connector
  30. Install positive LV output
    注
    1x nut, 13mm, 9 Nm, Make sure rubber boot is not pinched between cable terminal and pass through
  31. Install positive LV output cover to PCS cable
    注
    1x cover
  32. Remove logic cap and connect HVC logic connector
    注
    1x connector, 1x cap, Align connector then pull the handle to locking position get connector fully seated
  33. Install the RH body harness clips to B-pillar area
    注
    7x clips
  34. Connect RH body harness to TCU connector
    注
    2x connector
  35. Secure RH upper B-pillar bracket to body
    注
    2x bolts 10mm2.5 Nm
  36. Install the RH body harness ground strap around lower B-pillar
    注
    1x bolt, 10mm, 10 Nm
  37. Connect B-pillar camera and RH antenna connector
    注
    2x connectors, Secure red locking tab after installing connector
  38. Secure RH B-pillar applique to vehicle
    注
    1x clip, 2x tabs, Align B-Pillar applique into position and secure clips into body, Use caution not to damage the connectors
  39. Install bolts securing RH B-pillar applique to body
    注
    2x bolts, 8mm, 5 Nm
  40. Install RH B-pillar applique fasteners cover
    注
    4x clips, 1x tab, Slide tab into body first, then engage clips
  41. Install clip securing the RH rear main carpet to vehicle
    注
    1x clip
  42. Install RH body harness clips from B-pillar area
    注
    3x clips
  43. Connect RH body harness connector to RH rear door harness connector B-pillar area
    注
    1x connector
  44. Connect RH B-pillar impact accelerometer sensor connector
    注
    1x connector
  45. Make connections to RH retractor
    注
    2x connectors,Press the connector. When the connector is fully seated, you will hear the click sound of the secondary locking pin returning Installing connector, place retriever in B-pillar
  46. Install bolt securing RH retractor to base of B-pillar
    注
    1x patch bolt, 13mm, 40 Nm, Install new patch bolt (1004383-00-C)
  47. Install harness retaining bracket to RH B pillar body
    注
    1x connector bracket
  48. Connect the LH harness connectors around RH lower B-pillar area
    注
    3x connectors， Connect the connector and push in the red locking tab
  49. Install RH body harness clips along RH front sill area
    注
    1x clip
  50. Install clips securing LH seat harness to sill trim
    注
    5x clips, Tuck excess harness between harness bracket and body
  51. Connect connectors from harness clip at RH lower A-pillar area
    注
    3x connectors
  52. Secure harness clip to RH body controller
    注
    1x clip
  53. Connect connector to the right body harness
    注
    1x connector
  54. Unfold RH front main cabin carpet back to original position
    注
    1x clip
  55. Connect DCDC positive cable to right body harness
    注
    1x connector,1x clip Connect the connector and push in the red locking tab
  56. Connect J4 connector to RH body controller
    注
    1x connector, J4, Fully seat connector then engage lock
  57. Connect J2 connector to RH body controller
    注
    1x connector, J2, Fully seat connector then engage lock
  58. Connect J5 connector to RH body controller
    注
    1x connector, J5
  59. Connect J12 connector to RH body controller
    注
    1x connector, J12
  60. Connect seat connector to RH body controller
    注
    1x connector, 1x locking tab, J9
  61. Install RH body controller
    注
    1x W clip, Maneuver right body controller into position under IP carrier and align the W clip with body cut out, Then slide down controller to secure
  62. Install the bolt securing the right controller to body
    注
    1x nyloc nut, 10mm, 6 Nm,
  63. Secure RH body harness to RH body controller and A-pillar
    注
    3x clips
  64. Connect connectors to car computer
    注
    4x connector
  65. Instal harness connectors on left side of car computer
    注
    3x connectors. Install the plug in place and lock the locking tab
  66. Install harness clips from left of car computer
    注
    1x clips
  67. Install harness clips from lower of car computer
    注
    2x clips
  68. Install RH trunk side trim
  69. Connect RH trunk task light connector
    注
    1x connector
  70. Install clips for RH trunk side trim
    注
    2x clips
  71. Install trunk garnish assembly
    注
    6x clips, 4x locating tabs, Align locating tabs to slot, Verify trunk seal is fully seated along garnish
  72. Install RH load floor bracket
    注
    4x clips, 2x locations
  73. Install trunk sill trim assembly
    注
    4x clips, Align striker with center slot then 2 locators to slots then press to secure clips, Manipulate seal to overlap trim
  74. Install load floor
  75. Install package tray
    注
    5x tabs, 3 at the rear of panel and 2 on the sides, Slide towards rear of vehicle to install
  76. Connect package tray harness connector to RH body harness
    注
    1x connector
  77. Install package tray harness clips around upper C-pillar area
    注
    2x clips
  78. Install rear headliner to body
    注
    4x clips, 2x locator pins,Align the locating pin of the roof liner with the slot, and then push in the direction of the arrow to install the clip, ensuring that the seal overlaps with the trim
  79. Install LH coat hook screw
    注
    1x screw, T25, 2.5 Nm
  80. Close LH coat hook screw cover
    注
    2x securing tabs
  81. Install tether hook onto LH side rail assembly
    注
    2x tether hooks, Install new tether hook
  82. Install LH side rail assembly
    注
    4x clips, 2x locations, 2x tether hooks, Align the clips from bottom to top then press clips from top to bottom, Align the seal to sit on top of the trim
  83. Install LH upper B-pillar
    注
    3x clips,3x locator pins, Lower the seat belt slider to align it with the B-pillar panel, align the locating pin of the B-pillar upper trim panel with the slot, push in the direction of the arrow to install the clips after aligning them, Make sure the seal sits overlapping the trim
  84. Install LH middle B-pillar assembly
    注
    5x clips, 3x locator clips,Align the locator clips to slot, Then push in the direction of the arrow to install the clips after aligning them, Make sure the seal sits overlapping the trim
  85. Install LH lower B-pillar assembly
    注
    7x clips, 4x locator clips, Align the locator clips to slot, Then push in the direction of the arrow to install the clips after aligning them, Make sure the seal sits overlapping the trim
  86. Install LH C pillar assembly to body
    注
    3x clips, 3x tabs, Slide the back tabs into package tray then align clips
  87. Install bolster plastic bracket to LH side bolster
    注
    2x tabs, Install new bolster bracket
  88. Install LH side bolster
    注
    1x locator clip, 3x guide tabs, Align the bottom and side tabs then push inward to install
  89. Return 2nd row 60 seatback to vertical position
  90. Install LH lower A-pillar assembly
    注
    4x clips, 2x guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, Fully seat seal along trim
  91. Install clip securing LH lower A-pillar assembly
    注
    1x push clip
  92. Install LH IP end cap
    注
    5x clips, 2x guide tabs
  93. Install LH front primary seal
    注
    Verify seal is seated properly on all trim panels
  94. Install RH upper A-pillar trim
    注
    6x clips, 1x tether, 2x guide tabs,1x alignment pin, Slide bottom of trim along IP and speaker grill, attach tether to body side, Set clips starting at the bottom and work up, Pull seal over trim
  95. Connect RH sun visor connector
    注
    1x connector
  96. Install RH sun visor into headliner area
    注
    First push the connector and wire harness backward, then fold sun visor to the closed and folded down position but do not latch in place
  97. Install RH sun visor fastener
    注
    1x screw, T25, 3.5 Nm
  98. Install RH sun visor bracket cover
    注
    4x tabs
  99. Install RH coat hook screw
    注
    1x screw, T25, 2.5 Nm
  100. Close RH coat hook screw cover
    注
    2x clips
  101. Push RH coat hook closed
  102. Install the RH upper B-pillar
    注
    3x clips,3x locator pins,Lower the seat belt slider to align it with the B-pillar panel, align the locating pin of the B-pillar upper trim panel with the slot, push in the direction of the arrow to install the clips after aligning them, Make sure the seal sits overlapping the trim
  103. Install RH middle B-pillar assembly
    注
    5x clips, 3x locator clips,Align the locator clips to slot, Then push in the direction of the arrow to install the clips after aligning them, Make sure the seal sits overlapping the trim
  104. Install RH lower B-pillar assembly
    注
    7x clips, 5x locator clips,Align the locator clips to slot, Then push in the direction of the arrow to install the clips after aligning them, Make sure the seal sits overlapping the trim
  105. Install RH C pillar assembly to body
    注
    3x clips, 3x tabs, Slide the back tabs into package tray then align clips
  106. Install tether hook onto RH side rail assembly
    注
    2x tether hooks, Install new tether hook
  107. Install RH side rail assembly
    注
    4x clips, 2x locations, 2x tether hooks, Align the clips from bottom to top then press clips from top to bottom, Align the seal to sit on top of the trim
  108. Install bolster plastic bracket to RH side bolster
    注
    2x tabs, Install new bolster bracket
  109. Install RH side bolster
    注
    1x locator clip, 3x guide tabs, Align the bottom and side tabs then push inward to install
  110. Return 2nd row 40 seatback to vertical position
  111. Connect 2nd row seat harness and secure cushion
    注
    2x clips, 2x connectors, Insert buckles through holes, Slide rear inward then align front clips, Perform push-pull-push test
  112. Install RH lower A-pillar trim
    注
    4x clips, 2x guide tabs, Align the 2 front tabs then align the slot with harness bracket and then push rear clip to secure to lower B-pillar, Fully seat seal along trim
  113. Install clip for RH lower A-pillar trim
    注
    1x push clip
  114. Install RH passenger footwell duct to HVAC module
  115. Connect glove box assembly connectors
    注
    2x connectors
  116. Install glove box into IP carrier
    注
    10x clips, 3x locator pin, 1x datum
  117. Install screws securing glove box assembly to IP carrier
    注
    4x screws, T20, 2.3 Nm
  118. Connect glove box USB cable to car computer
    注
    1x connector, Engage locking tab
  119. Install clips securing passenger footwell duct
    注
    2x push clips
  120. Connect RH footwell cover connectors
    注
    3x connectors
  121. Install RH footwell cover
    注
    5x clips, 1x guide tab
  122. Install RH IP end cap
    注
    5x clips, 2x guide tabs
  123. Connect the LV battery power. See 低压电源 - 锂离子（断开和连接）.
  124. Close trunk via interior switch
  125. Hold brake pedal and select park on UI to disable EPB service mode
  126. Remove wheel chocks
  127. Raise all windows
  128. Close all four doors