23/04/2024 19:23:03
大灯 - 调节 - NA（工具法） (Test/Adjust)
校正代码 174000150 FRT 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。 注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
Adjust Headlights Using a Headlight Tester
Special tools required for this procedure:
| Supplier | Part Number | Description |
| Tesla | 1133367-00-A | HEADLIGHT TESTER, BEISSBARTH, MLD 815 |
- Open the LH front door and lower LH front window.
- Open the front trunk hood.
- Place the vehicle in Service Mode via touchscreen. See 维护模式.
- On the vehicle touchscreen, enter headlight adjustment mode: Controls > Service > Adjust Headlights.
- Turn on the headlights.
- Position the headlight tester tool ~11 in. (30 cm) from the front of the LH headlight lens.
- Adjust the height of the headlight tester tool to ~20.4 in. (68 cm) above the ground to align with the center point of the headlamp.
- Connect the headlight tester tool to an electrical outlet, and then turn on the headlight tester tool.
-
Adjust the knobs on the base of the
headlight tester tool until the tool is leveled, as indicated by the bubble gauge on the
tool.
注The bubble must be entirely inside of the center ring in order to properly align the headlights.
-
Turn on the alignment laser near the
top of the tool, and then rotate the tool as necessary to align the laser with the base of
both hood struts.
图 1. LH Hood Strut 
- On the headlight tester tool, select Test US, then select >Free Test.
- On the headlight tester tool, select Headlight, and then use the + or - buttons to change the Headlight type to "SAE".
- On the headlight tester tool, select Light, and then use the + or - buttons to change the Light type to LED.
-
On the headlight tester tool, select
Inclina., and
then use the + or
- buttons to set
the inclination.
注Inclination information is located on the headlight.
- On the headlight tester tool, select Height, and then + or - buttons to adjust to68CM.
- On the headlight tester tool, select OK.
- On the headlight tester tool, select OK again to proceed past fog light settings.
-
On the headlight tester tool, select
Laser to turn on
the headlight laser guide.
注Use of a flashlight can aid in finding marks, and shift vertical beam outboard 66mm from marking to properly align with light output.
-
On the headlight tester tool, select
Left low beam,
and then select Low
beam near the bottom of the screen.
注The "L" and "R" indicators at the bottom of the screen are reversed. For example, "L" is on the right side and "R" is on the left side.
-
On the steering wheel, select
Left and then use the left scroll wheel to adjust the beam
level: Target 0.00" +/- 1.0"
警告Do not sit in the vehicle, as this will affect headlight alignment.注There might be a delay between the scroll wheel input and actual headlight adjustment output.
- On the headlight tester tool, select Save to record the results.
- Roll the headlight tester tool to the RH headlight, and then position the tool ~30 cm from the front of the RH headlight lens.
-
On the headlight tester tool, select
Right low beam,
and then select Low
beam near the bottom of the screen.
注Make sure that High beam is not selected.注The "L" and "R" indicators at the bottom of the screen are reversed. For example, "L" is on the right side and "R" is on the left side.
-
On the steering wheel, select
Right and then use the right scroll wheel on the steering wheel
to adjust the beam level: Target 0.00" +/- 1.0"
警告Do not sit in the vehicle while using the scroll wheel as this will affect headlight alignment.注There might be a delay between the scroll wheel input and actual headlight adjustment output.
- On the headlight tester tool, select Save to record the results.
- On the headlight tester tool, select Save again to view test results.
- Close the front trunk hood.
- Raise LH front window.
- Close LH front door.