2026-07-02
执行常规检查 (Inspection)
校正代码 00030700 FRT 0.90 注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。
警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
- 2026-06-18: Released new procedure.
Procedure
-
Function check LH front door (exterior)
注Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
-
Function check LH front door (interior)
注Inspect and note functionality for the interior door release, puddle lamps, and manual release cable, From inside look for interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions
-
Function check all windows from master switch
注Document any abnormal operation/noises
-
Function check wipers and spray jets
注Ensure hood and doors are closed prior to activating wipers, Inspect and note functionality for wipers and wiper jets, Check for full range of motion, speed of motion, interference with other components, noises such as creaks, groans and clicks, pauses or incomplete actions
-
Function check all driver controls
注Shift stalk, turn signals, steering wheel scroll wheels, horns
-
Function check steering column through UI
注Move the column to its extreme position in each direction using steering wheel buttons, Return to original position
-
Function check the exterior lights
注Recommend assistance, inspect and note functionality of Headlight (LH and RH), Side Repeater (LH and RH), Taillight (LH and RH), CHMSL, Fog Light (LH and RH), Reverse Light (LH and RH), Front Turn Signal (LH and RH), Rear Turn Signal (LH and RH)
-
Function check hazard light switch
-
Function check LH rear door (exterior)
注Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
-
Function check RH rear door (exterior)
注Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
-
Function check RH front door (exterior)
注Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note noises such as creaks, groans and clicks, pauses or incomplete actions
-
Open hood
-
Remove rear apron
注14x clips
-
Remove fresh air gutter assembly
注3x clips
-
Check coolant level in reservoir
-
Check brake fluid level
-
Fill washer reservoir with fluid
-
Install fresh air gutter assembly
注3x clips
-
Install rear apron
注14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips
-
Close hood
-
Raise and support vehicle
注remove charging equipment
-
Raise vehicle partially and lower lift onto locks
注Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, Otherwise vehicle may tilt to the side
-
Check all four tire pressures manually
注4x tires, 4x caps, Set to specification if necessary, Refer to the "Tire and Loading Information" label located on the driver side B-pillar, Inspect wheels and tires for any bulges or damage while checking/setting pressures
-
Record tread depth for LH front tire
注Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
-
Record tread depth for RH front tire
注Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
-
Record tread depth for LH rear tire
注Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
-
Record tread depth for RH rear tire
注Measure and record the outer, center, and inner tread depths, Measure the circumferential tire grooves only, Do not place the tire tread gauge probe on the molded treadwear indicators, Recommend replacement if tread depth is 4/32in (3mm) or less
-
Measure and record LH rear brake pad thickness
注Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect LH rear brake rotor condition
注Check for excessive rust or wear, Minimum spec 26mm
-
Measure and record RH rear brake pad thickness
注Recommend replacement if 2 mm or less, Check both inboard and outboard pads
-
Inspect RH rear brake rotor condition
注Check for excessive rust or wear, Minimum spec 26mm
-
Measure and record RH front brake pad thickness
注Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect RH front brake rotor condition
注Check for excessive rust or wear, Minimum spec 30mm
-
Measure and record LH front brake pad thickness
注Recommend replacement if 2mm or less, Check both inboard and outboard pads
-
Inspect LH front brake rotor condition
注Check for excessive rust or wear, Minimum spec 30mm
-
Raise vehicle fully and lower lift onto locks
注Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
-
Remove bolts securing front aero shield
注7x bolts, 10mm, 5 Nm
-
Remove front aero shield from studs
注2x nuts, 15mm, 8 Nm
-
Remove rear aero shield clips
注2x clips, One clip on LH side wheel liner, One clip on RH side wheel liner
-
Remove rear aero shield
注11x bolts, 10mm, 5 Nm
-
Remove LH rear suspension cover
注1x bolt, 10mm, 6 Nm, 2x tabs
-
Remove RH rear suspension cover
注1x bolt, 10mm, 6 Nm, 2x tabs
-
Perform visual inspection of HV battery enclosure
注Check for any dents, scrapes, or other damage
-
Inspect underside of vehicle for fluid leaks
-
Perform inspection of steering components
注Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
-
Perform inspection of front suspension components
注Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
-
Perform inspection of rear suspension components
注Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
-
Install RH rear suspension cover
注1x bolt, 10mm, 6 Nm, 2x tabs
-
Install LH rear suspension cover
注1x bolt, 10mm, 6 Nm, 2x tabs
-
Install rear aero shield
注11x bolts, 10mm, 5 Nm, Apply Loctite 222 onto rear aero shield bolts before installing
-
Install rear aero shield
注2x clips, One clip on LH side wheel liner, One clip on RH side wheel liner
-
Position front aero shield onto vehicle and secure with two nuts
注2x nuts, 15mm, 8 Nm, Hand-tighten the nuts to temporarily hold the panel in place
-
Install front aero shield bolts
注7x bolts, 10mm, 5 Nm, Apply Loctite 222 onto bolts before installing
-
Lower vehicle until tires are touching ground
注Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
-
Raise all four windows
-
Close all four doors
-
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance
注The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
-
Inspect vehicles alignment
注Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction