校正代码 17403012 FRT 2.04 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

1. Raise and support vehicle
   注

   Ensure vehicle is not charging

   

   

   

2. Open LH front door

   

3. Lower LH front window

   

4. Open RH front door

   

5. Lower RH front window

   

6. Move RH front seat backward

   

7. Open hood

   

   

8. Remove rear apron
   注

   14x clips

   

   

9. Remove fresh air gutter assembly
   注

   3x clips

   

   

10. Remove LH wiper arm nut cover
    注

    1x cover

    

11. Release LH wiper arm hose nozzle
    注

    1x hose

    

    

12. Remove nut securing LH wiper arm to wiper module
    注

    1x nut, 15mm, 25 Nm

    

13. Remove LH wiper arm assembly from vehicle

    

    

14. Remove RH wiper arm nut cover
    注

    1x cover

    

15. Release RH wiper arm hose nozzle
    注

    1x hose

    

    

16. Remove nut securing RH wiper arm to wiper module
    注

    1x nut, 15mm, 25 Nm

    

17. Remove RH wiper arm assembly from vehicle

    

    

18. Release clips on the LH shock tower cover and move the tower cover to side
    注

    2x clips

    

    

19. Release clips on the RH shock tower cover and move the tower cover to side
    注

    2x clips

    

    

20. Remove LH hood hinge cover
    注

    2x clips,1x dowel hole

    

    

    

21. Remove RH hood hinge cover
    注

    2x clips,1x dowel hole

    

    

    

22. Disconnect main washer hose
    注

    1x clip

    

    

23. Remove clip securing FRL harness to cowl screen
    注

    1x clip

    

24. Remove clip securing main washer hose to cowl screen
    注

    1x clip

    

25. Remove cowl screen
    注

    2x push clips, 4x clipsRelease cowl from windshield retainer

    

    

    

    

    

26. Disconnect wiper module connector
    注

    1x connector, Do not place limbs within the linkage movement area as wiper arms will automatically transition to parking mode

    

27. Remove bolts securing wiper module to body
    注

    3x bolts, 10mm, 7 Nm

    

28. Remove wiper module from vehicle
    注

    Keep your fingers away from any potential pinch points and moving parts while connecting and installing the wiper module, Do not attempt to test the module until it is fully installed in the vehicle

    

    

29. Remove fresh air intake assembly
    注

    2x studs, Lift cowl as needed

    

    

    

    

30. Remove LH front wheel center cap
    注

    1x cap, Pull the inner side of the adjacent 2 claws on the wheel center cap by hands

    

    

31. Loosen LH front wheel nuts
    注

    5x nuts, 21mm, 175 Nm

    

32. Raise vehicle partially and lower lift onto locks
    注

    Set vehicle to a comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, Otherwise vehicle may tilt to the side

    

    

33. Remove LH front wheel
    注

    5x nuts, 21mm, 175 Nm

    

34. Partially remove LH front wheel liner
    注

    8x clips, 1x bolt, 10mm, 5 Nm

    

    

    

    

    

35. Disconnect the front harness connectors for the LH side repeater and camera
    注

    2x connectors, Release locking tabs

    

36. Lower vehicle partially and set lift onto locks
    注

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height

    

    

37. Power off vehicle from center display
    注

    Via Controls > Safety > Power Off, Select Power Off button at warning dialog box

    

    

38. Disconnect LV battery and first responder loop
    注

    2x connectors, Ensure that one minute has passed after window movement before performing the power-off, Release green locking tab, Press black tab then pull black connector lock outwards to release connection, Release red lock tab on FRL, Allow 2 minutes for all electrical circuits to fully discharge

    

    

    

    

39. Disconnect thermal sub-harness from front controller
    注

    1x connector, Depress locking tab and rotate to release

    

40. Remove bolts securing front controller shield assembly and remove from vehicle
    注

    2x bolts, 10mm, 8.5 Nm

    

    

41. Disconnect front controller harness connectors
    注

    5x connectors, 1x harness guide, Release locking tab if equipped

    

    

42. Remove bolt securing ground cable to front controller
    注

    1x bolt, 10mm, 8.5 Nm,

    

43. Remove bolts securing front controller
    注

    3x bolts, 10mm, 10 Nm

    

44. Tilt front controller forward for access
    注

    Lift cowl screen up appropriately

    

    

45. Release LV negative harness clip from front controller
    注

    1x clip

    

    

46. Remove front controller from vehicle
    注

    1x tab

    

    

    

    

47. Release RH footwell cover
    注

    2x magnets, 1x guide tab, 1x connector

    

    

48. Partially release RH front primary door seal
    注

    Release lower section of RH front primary door seal

    

49. Remove RH IP end cap
    注

    5x clips, 2x guide tabs

    

    

50. Remove RH lower A-pillar trim
    注

    4x clips, 2x guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release front tabs from carpet

    

    

51. Remove RH knee airbag bolt covers
    注

    2x covers

    

    

52. Remove RH knee airbag bolts
    注

    4x bolts, EP10, 8.5 Nm, Discard bolts after removal, brake loose e10 by hand then use e-ratchet to back off hardware

    

    

53. Remove RH knee air bag assembly
    注

    1x air bag connector, 1x connector, Peel back plastic film, Release by pulling back both white tabs simultaneously, Avoid straining harness, Only one tab visible in image matching tab is on opposite side

    

    

    

    

54. Remove clips securing passenger footwell duct
    注

    2x clips

    

55. Disconnect glove box USB cable connector from car computer
    注

    1x connector, Release locking tab then release connector

    

56. Remove screws securing glove box to IP
    注

    4x screws, T20, 2.3 Nm

    

    

    

57. Release glove box from IP assembly
    注

    10x clips, 3x locator pins, 1x datum, Avoid damage to electromagnetic switch

    

    

58. Remove glove box
    注

    2x connectors

    

    

59. Remove RH passenger footwell duct from HVAC module

    

    

60. Disconnect RH IP air wave duct thermistor connector
    注

    1x connector

    

61. Remove RH IP air wave duct from HVAC module

    

    

62. Fold RH front main cabin carpet aside for access
    注

    2x clips, Lift center piece and pull carpet back, Release seat harness from clips to allow carpet to fold back more

    

    

63. Release windshield heater connecter
    注

    1x connector

    

    

64. Release RH grommet from body

    

    

65. Remove electrical tape securing harness bundle to rubber dust boot
    注

    Use a razor blaze, carefully cut electrical tape away to expose rubber dust boot

    

    

66. Remove locking pin from connector
    注

    Carefully pry pin out of connector and fully remove locking pin

    

    

67. Remove coax cable needed for the side repeater overlay terminal 2 (LHS)
    注

    Inspect all components for damage

    

    

    

68. Apply harness tape onto LH coax overlay cable before installation
    注

    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is in the vehicle

    

    

    

69. Release frunk harness cover
    注

    3x tabs

    

    

70. Position M3 LH coax overlay cable into place, Place through LH wheel liner
    注

    Pull till you have roughly 12 inches of cable towards the interior of the vehicle

    

    

71. Pull LH coax overlay cable through frunk harness
    注

    Pull harness towards car computer, Route under brake booster lower connector

    

    

72. Tape coax overlay onto fish nylon tape

    

73. Pull LH coax overlay cable through bulkhead and into interior cabin

    

    

    

    

74. Remove nylon fish tape
    注

    Remove tape the pull nylon fish tape out of vehicle

    

    

75. Disconnect side repeater cameras connector from car computer
    注

    1x locking connector

    

    

    

76. Remove locking pin from side repeater cameras connector
    注

    Carefully pry pin out of connector and fully remove locking pin

    

    

77. Remove coax terminal 2 (LHS) cable from connector
    注

    Inspect all components for damage

    

    

    

78. Insert new side repeater coax terminal 2 (LHS) cable onto side repeater cameras connector
    注

    Ensure both coax cables are fully seated into connector, Audible locking and flush mounting to confirm

    

    

79. Secure locking pin to connector
    注

    Align tabs of lock in connector housing, Ensure flush installation of locking pin to connector housing

    

    

80. Connect side repeater cameras connector onto car computer
    注

    1x locking connector

    

    

    

81. Position LH coax overlay cable onto frunk main harness, Secure cable onto harness using zip ties
    注

    7x zip-ties, Trim off excess material after harness has been secured

    

    

    

    

82. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    注

    Cut the coax connector only

    

83. Connect front harness connectors for LH side repeater and camera
    注

    2x connectors, Secure locking tabs

    

84. Secure RH grommet from body
    注

    Use electrical tape to wrap the end of the dust boot

    

    

    

85. Secure frunk harness cover
    注

    3x tabs

    

    

86. Secure windshield heater connector
    注

    1x connector

    

    

87. Install LH front wheel liner to vehicle
    注

    8x clips, 1x bolt, 10mm, 5 Nm

    

    

    

    

    

88. Install LH front wheel
    注

    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool

    

89. Lower vehicle until tires are touching ground
    注

    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered

    

    

    

90. Torque LH front wheel
    注

    5x nuts, 21mm, 175 Nm

    

91. Install LH front wheel center cap
    注

    1x cap, Ensure that the cap is installed in place

    

92. Place front controller into vehicle for installation
    注

    1x tab

    

    

    

    

93. Secure LV negative harness clip from front controller
    注

    1x clip

    

94. Tilt front controller backward for installation
    注

    Lift cowl screen up appropriately

    

    

95. Install bolts securing front controller
    注

    3x bolts, 10mm, 10 Nm

    

96. Install bolt securing ground cable to front controller
    注

    1x bolt, 10mm, 8.5 Nm,

    

97. Connect front controller harness connectors
    注

    5x connectors, 1x harness guide, Secure locking tab, if equipped

    

98. Install front controller shield to front controller
    注

    2x bolts, 10mm, 8.5 Nm

    

99. Connect thermal sub-harness to front controller
    注

    1x connector, Rotate fully to secure locking tab

    

100. Install wiper module to vehicle
     注

     Keep your fingers away from any potential pinch points and moving parts while connecting and installing the wiper module, Do not attempt to test the module until it is fully installed in the vehicle

     

     

101. Install bolts securing wiper module
     注

     3x bolts, 10mm, 7 Nm

     

102. Connect wiper module connector
     注

     1x connector, Do not place limbs within the linkage movement area as wiper arms will automatically transition to parking mode

     

103. Install cowl screen to vehicle
     注

     2x push clips, 4x clips

     

     

     

     

     

104. Install LH shock tower cover
     注

     3x push clips

     

     

105. Install LH hood hinge cover
     注

     2x clips,1x dowel hole, Install the lower portion onto the hinge, then press straight up to fully seat the cover

     

     

     

106. Install RH shock tower cover
     注

     3x push clips

     

     

107. Install RH hood hinge cover
     注

     2x clips,1x dowel hole, Install the lower portion onto the hinge, then press straight up to fully seat the cover

     

     

     

108. Install clip securing washer hose to cowl screen
     注

     1x clip

     

109. Install clip securing harness to cowl screen
     注

     1x clip

     

110. Connect main washer hose
     注

     1x clip

     

111. Install RH wiper arm and hose assembly onto vehicle

     

     

112. Install nut securing RH wiper arm to wiper module
     注

     1x nut, 15mm, 25 Nm, Make sure the wiper tip is aligned between the two indicators at corner of windshield

     

113. Secure RH wiper arm washer nozzle
     注

     1x hose, Hose is routed below the arm

     

114. Install RH wiper arm nut cover
     注

     1x cover

     

115. Install LH wiper arm and hose assembly onto vehicle

     

     

116. Install nut securing LH wiper arm to wiper module
     注

     1x nut, 15mm, 25 Nm, Make sure the wiper tip is aligned between the two indicators at corner of windshield

     

117. Secure LH wiper arm washer nozzle
     注

     1x hose, Hose is routed below the arm

     

118. Install LH wiper arm nut cover
     注

     1x cover

     

119. Install fresh air intake assembly
     注

     2x studs, Lift cowl as needed

     

     

     

     

120. Position frunk assembly to vehicle
     注

     8x clips, 3x locator pins, Ensure clips are aligned at thermal beam, Replace any clips if broken or missing

     

     

     

     

     

121. Install bolts securing frunk assembly
     注

     4x bolts, 10mm, 5 Nm, Number of bolts may vary depending on build date

     

122. Install access panel to frunk assembly
     注

     3x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push forward to secure clips

     

     

123. Install fresh air gutter assembly
     注

     3x clips

     

     

124. Unfold RH front main cabin carpet back to original position
     注

     1x locator clip

     

     

     

125. Install RH IP air wave duct to HVAC module

     

     

126. Install clips securing RH IP air wave duct
     注

     2x push clips

     

127. Connect thermistor connector RH IP air wave duct
     注

     1x connector

     

128. Install RH passenger footwell duct to HVAC module

     

     

129. Position glove box assembly
     注

     2x connectors

     

     

130. Install glove box into IP assembly
     注

     10x clips, 3x locator pin, 1x datum, If necessary, Replace any clips that are broken

     

     

131. Install screws securing glove box assembly to IP assembly
     注

     4x screws, T20, 2.3 Nm

     

     

     

132. Connect glove box USB cable to car computer
     注

     1x connector, Engage locking tab

     

133. Install clips securing passenger footwell duct
     注

     2x push clips, Ensure that the footwell duct is installed in place

     

134. Install RH IP end cap
     注

     5x clips, 2x guide tabs

     

     

135. lnstall seat lower section of RH front primary seal
     注

     Verify seal is seated properly on all trim panels

     

136. Install RH knee air bag assembly
     注

     1x air bag connector, 1x connector, Ensure airbag connector is fully engaged, Place plastic film back over squib assembly

     

     

     

     

137. Install RH knee airbag bolts
     注

     4x bolts, EP10, 8.5 Nm, use socket wrench to start hardware by hand to avoid cross threading. Avoid Over tightening Hardware during installation avoid using power tools

     

     

138. Install RH knee air bag bolt covers
     注

     2x covers

     

     

139. Install RH footwell cover
     注

     2x magnets, 1x guide tab, 1x connector

     

     

140. Connect first responder loop and LV battery
     注

     2x connectors, Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated

     

     

     

141. Install rear apron
     注

     14x clips, Hold rear wall of frunk to keep from flexing while engaging front clips

     

     

142. Close hood

     

143. Move RH front seat to original position

     

144. Raise RH front window

     

145. Close RH front door

     

146. Verify operation of windshield washers and wipers

     

147. Clear DAS Calibration through UI
     注

     Controls > Service > Camera Calibration, Select Clear Calibration, Verify calibration was cleared successfully, Wait for prompt to disappear automatically before continuing, Calibration in Progress message and progress icon will appear during the next drive cycle

     

     

     

148. Raise LH front window

     

149. Close LH front door

     

150. Remove lift arms from below vehicle
     注

     Lower rack arms fully and remove them from under vehicle

     

151. Vehicle will need to be driven by customer to complete calibration procedure. During this time DAS functions will be completely unavailable