2026-11-04

外侧护板 - 第一排座椅 - 左侧 - 驾驶员座椅 ((拆卸和更换))

校正代码 1307010122 FRT 0.18 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

  • 2026-11-04: Added information about the tab that attaches the side shield to the front seat.
  • 2026-07-17: Added a note to ensure that the seat is high enough to access the bolt securing the outboard side shield to the seat frame.

Hexagon - 1060071-00-A

Mini Ratchet Bit Set - 1450424-00-A

Note
In certain regions, if the 1st row outboard shield is supplied as an assembly with buttons and switch pre-installed, skip the steps of removing/installing the buttons and switch.

拆卸

  1. Open the LH front door.
  2. Move the driver's seat fully forward, and adjust the seat cushion height to maximum.
    CAUTION
    Do not allow the seat headrest to compress the sun visor as it might crack the mirror.
  3. 将安全带释放钥匙 (1133787-00-A) 插入到安全带预紧装置耦合的底部，以从预紧装置中松开安全带。
    Warning
    本程序所含视频仅作为补充材料予以概括说明。请遵循本程序所列的所有步骤，以避免部件损坏和/或人身伤害。
  4. Remove the bolt that attaches the driver seat outboard side shield to the seat frame.
    Tip
    推荐使用以下工具
    • 1/4 英寸无绳棘轮钻头
    Note
    Ensure the front of the seat is high enough to access the bolt.
  5. Pull the driver seat outboard side shield away from the seat frame to release the tab that attaches the side shield to the front of the seat frame.
  6. Pull the driver seat outboard side shield away from the seat frame to release the clip that attaches the side shield to the upper part of the seat frame.
    Warning
    本程序所含视频仅作为补充材料予以概括说明。请遵循本程序所列的所有步骤，以避免部件损坏和/或人身伤害。
  7. Disconnect the electrical harness from the backrest and cushion adjust switch connector, if so equipped.
  8. Remove the driver seat outboard side shield from the vehicle.
  9. Carefully release the clips that attach the seat cushion and seat back buttons to the driver seat backrest and cushion adjust switch, and then remove the buttons from the outboard side shield.
  10. Remove the screws securing the 8 way switch to LH front outer side cover, then remove LH front outer side cover from 8 way switch assembly.
    Tip
    推荐使用以下工具
    • 梅花 T20 套筒

安装

  1. Install the screws securing the 8 way switch to LH front outer side cover, then install LH front outer side cover from 8 way switch assembly.
    1.7 Nm (1.3 lbs-ft)
    Tip
    推荐使用以下工具
    • 梅花 T20 套筒
  2. Install the clips that attach the seat cushion and seat back buttons to the driver seat backrest and cushion adjust switch, and then install the buttons to the outboard side shield.
  3. Place the driver seat outboard side shield to the vehicle.
  4. Connect the electrical harness from the backrest and cushion adjust switch connector, if so equipped.
  5. Install the upper and lower part clips that attaches the side shield to the center of the seat frame.
  6. Push inward to secure the outboard side shield assembly tab to the front seat assembly, and then install the screw that attaches the driver seat outboard side shield to the seat frame.
    5 Nm (3.7 lbs-ft)
    CAUTION
    Carefully push the outboard side shield assembly to avoid damage.
    Tip
    推荐使用以下工具
    • 1/4 英寸无绳棘轮钻头
  7. Return the seat back to the original position.
  8. Install LH front seat belt retractor to seat.
  9. Raise LH front window.
  10. Close the LH front door.