校正代码 21153002 FRT 0.54 注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

1. Open the LH front door.
2. Lower both front windows.
3. Open the RH front door.
4. Move the RH front seat backward.
5. Open the hood.

   

6. Power off the vehicle using the touchscreen.

   

7. Remove the rear underhood apron.

   

   

8. Disconnect the LV battery connector and First Responder Loop.

   

   

   

9. Remove RH front floor mat

   

10. Remove RH footwell cover
    注

    3x magnets, 1x connector, 4x datums

    

    

11. Remove RH console side carpet
    注

    11x clips, 2x datums

    

    

12. Remove RH front door sill trim panel
    注

    8x clips, 3x datums

    

    

13. Remove RH IP end cap
    注

    3x clips

    

14. Remove RH mid A-pillar trim
    注

    2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim

    

    

    

15. Remove RH lower A-pillar trim
    注

    1x bolt, T25, 5 Nm, 2x clips, 1x datum

    

    

    

16. Fold RH front cabin carpet aside for access

    

17. Release harness from RH footrest panel
    注

    1x clip

    

18. Release RH footrest panel
    注

    2x bolts, 10mm, 5 Nm, 2x nut, 10mm, 5 Nm

    

19. Remove RH footrest panel
    注

    Fold RH primary support carpet up, Rotate RH footrest panel out of vehicle

    

    

20. Release connector to connectivity module
    注

    1x connector, Move release lock rearward before removal

    

    

21. Put on ESD wrist strap and connect to vehicle ground

    

22. Remove the car computer top cover fasteners
    注

    6x screws, T10, 1.4 Nm, Discard after removal

    

23. Remove car computer cover

    

    

24. Remove connectivity board mounting screws
    注

    5x screws, T10, 0.7 Nm, Discard after removal

    

25. Slide the connectivity board down to separate connector and remove
    注

    1x connector, Ensure full disengagement of connectivity board before attempting to remove

    

    

26. Slide the connectivity board in to the PCB connector
    注

    1x connector, 1x datum, Align datum with slot in connectivity card and fully engage

    

    

    

27. Install mounting screws to secure connectivity board
    注

    5x screws, T10, 0.7 Nm, Install new fasteners

    

28. Install car computer cover

    

    

29. Install top cover mounting screws
    注

    6x screws, T10, 1.4 Nm, Install new screws

    

30. Remove ESD wrist strap

    

31. Install connector to connectivity module
    注

    1x connector, Slide lock underneath connector

    

    

32. Connect the First Responder Loop and LV battery connector.

    

    

33. Install the rear underhood apron.

    

    

34. Close the hood.
35. Place vehicle in service mode with touchscreen
    注

    Select Controls > Software , Touch and hold "Model" for 2 seconds then release, Use the screen keyboard to type "service" into dialog box and select OK button, Select "X" at upper left corner to exit 'Service Settings' dialogue box

    

    

    

36. Reinstall firmware via UI
    注

    Via Controls > Service Mode > Software Reinstall, Select Reinstall button at Software Reinstall dialogue box, Reinstall will begin immediately, Once firmware redeploy is complete, Verify release notes are present via UI

    

    

37. Once firmware redeploy is complete, Verify release notes are present via UI
    注

    If redeploy fails then error message will appear

    

38. 运行 ODIN 例行程序 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
39. Install RH footrest panel
    注

    Rotate RH footrest panel onto vehicle, Fold RH primary support carpet down

    

    

40. Secure RH footrest panel
    注

    2x bolts, 10mm, 5 Nm, 2x nut, 10mm, 5 Nm

    

41. Secure harness to RH footrest panel
    注

    1x clip

    

42. Fold RH main carpet back into place

    

43. Install RH footwell cover
    注

    3x magnets, 4x datums, 1x connector

    

    

44. Install RH lower A-pillar trim
    注

    1x bolt, T25, 5 Nm, 2x clips, 1x datum

    

    

45. Install RH mid A-pillar trim
    注

    2x clips, 3x datums, Verify weather seal is seated properly

    

    

    

46. Install RH IP end cap
    注

    3x clips

    

47. Install RH front door sill trim panel
    注

    8x clips, 3x datums

    

    

48. Install RH front floor mat

    

49. Move the RH front seat to its original position.
50. Calibrate the RH falcon wing door.

    

51. Raise the RH front window.
52. Close the RH front door.
53. Calibrate the LH falcon wing door.

    

54. Verify BT, WiFi, and LTE are functioning properly

    

55. Raise the LH front window.
56. Close the LH front door.