29/05/2023 18:33:08

喇叭 - 低音（拆卸和更换）

校正代码 17530302 0.30 注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至LaborTimeFeedback@tesla.com。 注意：执行下述程序时，请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。

拆卸

Warning IconA warning icon, calling your attention to a possibly risky situation
警告
尽管此程序已经过验证，但仍是一个草案。可能没有警告和注意事项。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。请将校正修理内容及反馈发送至ServiceDevelopment@teslamotors.com。
  1. Open the LH front door.
  2. Lower the LH front window.
  3. Remove the LH front wheel. See 轮毂总成（拆卸和安装）.
  4. Release the clips (x6) and push nut that partially attach the front portion of the LH front wheel house liner to the vehicle body, and then move the liner aside for access.
    提示： 推荐使用以下工具：
    • 卡子撬具
  5. Disconnect the low tone horn locking connector.
    提示： 推荐使用以下工具：
    • Small flat head screwdriver
    Informational PurposesAn informational icon, calling your attention
    注
    Release the red locking tab.
  6. Disconnect the high tone horn locking connector.
    提示： 推荐使用以下工具：
    • Small flat head screwdriver
    Informational PurposesAn informational icon, calling your attention
    注
    Release the red locking tab.
  7. Remove the nut that attaches the horn assembly to the vehicle body, and then remove the horn assembly from the vehicle.
    提示： 推荐使用以下工具：
    • 2 英寸加长件
    • 10 毫米深套筒
    • 回旋头棘轮/回旋头扭矩扳手
  8. Remove the nut that attaches the low tone horn to the horn assembly bracket, and then remove the low tone horn from the bracket.
    提示： 推荐使用以下工具：
    • 10 毫米套筒
    • Adapter 1/4in Dr. to 1/4in Hex Bit Quick Change
    • Cordless 1/4in Hex Driver

安装

  1. Position the low tone horn on the horn assembly bracket, and then install the nut that attaches the low tone horn to the bracket.
    9 Nm (6.6 lbs-ft)
    提示： 推荐使用以下工具：
    • 10 毫米套筒
    • Adapter 1/4in Dr. to 1/4in Hex Bit Quick Change
    • Cordless 1/4in Hex Driver
    • 带角度测量的扭矩扳手
  2. Position the horn assembly on the vehicle, and then install the nut that attaches the horn assembly to the vehicle body.
    12 Nm (8.8 lbs-ft)
    提示： 推荐使用以下工具：
    • 2 英寸加长件
    • 10 毫米深套筒
    • 回旋头棘轮/回旋头扭矩扳手
  3. Connect the high tone horn locking connector.
    Informational PurposesAn informational icon, calling your attention
    注
    Verify the red locking tab is fully seated and engaged.
  4. Connect the low tone horn locking connector.
    Informational PurposesAn informational icon, calling your attention
    注
    Verify the red locking tab is fully seated and engaged.
  5. Install the clips (x6) and push nut that attach the front portion of the LH front wheel house liner to the vehicle body.
  6. Install the LH front wheel. See 轮毂总成（拆卸和安装）.
  7. Raise the LH front window.
  8. Close the LH front door.