2025-11-22
饰板总成 - 前 (HW4)（拆卸和更换）
10011032 1.02
注意：除非本程序中另有明确规定，否则上述校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。
注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈，请发送电子邮件至ServiceManualFeedback@tesla.com。。
注意：执行下述程序时，请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。
- 2025-11-17: Replaced radar heater disconnect step with reference to rework procedure. Removed steps to reinstall and reconnect radar heater.
- 2023-11-30: Reorganized the procedure.
拆卸
- Remove the front fascia harness. See 拆卸 - HW4.
-
If the radar heater has not been permanently disconnected, perform the rework. See 加热器 - 雷达（返工）（2021 年 7 月 1 日之前生产的车辆） or 加热器 - 雷达（返工）（2021 年 7 月 1 日之后生产的车辆）.
-
Remove the screws (x3) that attach the LH front fascia lamp to the vehicle, then repeat this step on the RH side.
TIp推荐使用以下工具：
- 梅花 T25 套筒
- 4 英寸加长件
- 棘轮/扭矩扳手
-
Remove the tabs (x4) that attach the LH front fascia lamp to the vehicle, then repeat this step on the RH side.
TIp推荐使用以下工具：
- Small flat head screwdriver
-
Remove the clips (x2) that attach the front fascia foam to the vehicle.
-
Remove the bolts (x2) and release the clips (x4) that attach the valance to the front fascia assembly.
TIp推荐使用以下工具：
- 10 毫米深套筒
- 棘轮/扭矩扳手
-
Release the clips (x10) that attach the valance to the front fascia assembly.
-
Remove the bolts (x2) that attach the front fascia grille to the front fascia assembly.
TIp推荐使用以下工具：
- 梅花 T25 套筒
- 4 英寸加长件
- 棘轮/扭矩扳手
-
Release the tabs (x11) that attach the front fascia grille to the front fascia assembly, and then remove the grille from the assembly.
TIp推荐使用以下工具：
- 梅花 T25 套筒
- 4 英寸加长件
- 棘轮/扭矩扳手
-
Remove the screw and release the tabs (x6) that attaches the T badge support to the front fascia.
TIp推荐使用以下工具：
- 梅花 T25 套筒
- 棘轮/扭矩扳手
- Small flat head screwdriver
-
Remove the front fascia from the vehicle.
安装
-
Secure the tabs (x6), then install the screw that attach the T badge support to the front fascia.
3 Nm (2.2 lbs-ft)TIp推荐使用以下工具：- 梅花 T25 套筒
- 棘轮/扭矩扳手
- 4 英寸加长件
-
Secure the tabs (x11) that attach the grille to the assembly.
注Position tabs into place prior to applying pressure.注Verify the grille is fully seated.
-
Install the bolts (x2) that attach the front fascia grille to the front fascia assembly.1 Nm (.7 lbs-ft)TIp推荐使用以下工具：
- 梅花 T25 套筒
- 棘轮/扭矩扳手
- 4 英寸加长件
-
Install the clips (x2) that attach the front fascia foam to the vehicle.
-
Secure the tabs (x10) that attach the valence to the front fascia assembly.
注Position the tabs into place prior to applying pressure. Verify the valance is fully seated onto the front fascia assembly.
-
Fasten the clips (x4), and then install the bolts (x2) that attach the valance to the front fascia assembly.3 Nm (2.2 lbs-ft)TIp推荐使用以下工具：
- 梅花 T25 套筒
- 棘轮/扭矩扳手
- 4 英寸加长件
-
Install the screws (x3) that attach the LH front fascia lamp to the vehicle, then repeat this step on the RH side.2.5 Nm (1.8 lbs-ft)TIp推荐使用以下工具：
- 梅花 T25 套筒
- 棘轮/扭矩扳手
- 4 英寸加长件
-
Secure the tabs (x4) that attach the LH front fascia lamp to the vehicle, then repeat this step on the RH side.
-
Install the front fascia harness. See 安装 - HW4.
注