2023-06-23

Aero Lens - Instrument Panel (Remove and Replace)

校正代码 14050012 1.50 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See 平均维修工时 to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure proper PPE is worn when performing the below procedure.

  • 2023 年 4 月 20 日:添加了有关非 HW4 车辆附加接地带零件号的说明。
  • 2023 年3 月 31 日:添加了有关再制造基线/安装锁片的说明。
Warning IconA warning icon, calling your attention to a possibly risky situation
警告
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
Informational PurposesAn informational icon, calling your attention
更换流线型透镜总成时可能需要拆下某些基线/安装锁片。这属于正常情况,并不会对车辆功能造成不利影响。

拆卸

  1. 打开左前车门。
  2. 降下左侧和右侧前车窗。
  3. 将驾驶位座椅移至最后端。
  4. 拆下左侧仪表板端盖。请参阅End Cap - Instrument Panel - LH (Remove and Replace)
  5. 拆下 A 柱左侧中间饰板。请参阅Trim - A-Pillar - Middle - LH (Remove and Replace)
  6. 拆下左侧仪表板左中饰板。请参阅Trim - Middle - Instrument Panel - LH (Remove and Replace)
  7. 拆下左侧遮阳板边框 A 柱饰板。请参阅Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace)
  8. 拆下左侧 A 柱上部饰板。请参阅Trim - A-Pillar - Upper - LH (Remove and Replace)
  9. 将转向柱移至最后部,压至最底部。
  10. 打开右前车门。
  11. 将副驾位座椅移至最后端。
  12. 拆下前备箱后部挡板。请参阅Underhood Apron - Rear (Remove and Replace)
  13. 断开低压电源。请参阅LV Power (Disconnect and Connect)
  14. 拆下右侧仪表板端盖。请参阅End Cap - Instrument Panel - LH (Remove and Replace)
  15. 拆下右侧 A 柱中间饰板。请参阅Trim - A-Pillar - Middle - LH (Remove and Replace)
  16. 拆下右前门槛饰板。请参阅Trim - Sill Panel - Front - LH (Remove and Replace)
  17. 拆下右侧 A 柱下部饰板。请参阅Trim - A-Pillar - Lower - LH (Remove and Replace)
  18. 拆下右侧遮光板 A 柱饰板。请参阅Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace)
  19. 拆下右侧 A 柱上饰板请参阅Trim - A-Pillar - Upper - LH (Remove and Replace)
  20. 从中控台上拆下中控台手机底座总成。但不要从手机底座上取下感应式充电器。请参阅Phone Dock - Center Console (Remove and Replace)
  21. 从中控台上拆下仪表板维修面板总成。但不要从维修面板上拆下座舱温度传感器风扇。请参阅Service Panel - Instrument Panel (Remove and Replace)
  22. 拆下触摸屏。请参阅Touchscreen (HW3) (Remove and Replace)
  23. 松开将仪表板封闭板连接到仪表板的锁片(4 个),然后从仪表板上拆下封闭板。
  24. 拆下右侧仪表板中间饰板。请参阅Trim - Middle - Instrument Panel - RH (Remove and Replace)
  25. 拆下主仪表板装饰。请参阅Decor - Instrument Panel - Main (Remove and Replace)
  26. 拆下副驾位脚垫。
  27. 拆下副驾位脚部空间盖板。请参阅Cover - Footwell - Passenger (Remove and Replace)
  28. 拆下中控台右侧面板地毯。 请参阅Carpet - Side Panel - Center Console - LH (Remove and Replace)
  29. 拆下副驾位膝部气囊总成。但是,从仪表板拆下膝部气囊总成后,不要将部件从膝部气囊总成上拆下。请参阅Knee Airbag - Front Passenger (Remove and Replace)
  30. 拆下手套箱。请参阅Glove Box (Remove and Replace)
  31. 移除副驾位仪表板导管。请参阅Duct - Instrument Panel - Front Passenger (Remove and Replace)
  32. 拆下仪表板支架横梁固定用螺栓(2 个)。
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米套筒
  33. 断开副驾位安全气囊电气连接器(3 个)
    Informational PurposesAn informational icon, calling your attention
    同时拉下弹簧锁,松开安全气囊连接器。
  34. 拆下仪表板右下方螺钉(3 个)。
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  35. 拆下仪表板中下方螺钉(6 个)。
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    如果在非 HW4 车辆上使用 1562948-70-D 版本零件,则将接地带 1679240-00-a 添加到流线型透镜总成上。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  36. 拆下仪表板左下方螺钉(3 个)。
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  37. 松开仪表盘电气线束夹,然后断开电气连接器。
  38. 松开仪表板饰板电气线束,然后断开电气连接器。
  39. 将下部仪表板总成放置于远离仪表板分总成的位置。
    Informational PurposesAn informational icon, calling your attention
    基线(6 条)。
    Informational PurposesAn informational icon, calling your attention
    尽可能向后移动顶部边缘,但不要对总成施加过大的压力。
  40. 松开仪表板接地线束夹,然后拆下接地线束螺栓。
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米套筒
    Informational PurposesAn informational icon, calling your attention
    注意线束位于触摸屏右侧支架后方。
    Informational PurposesAn informational icon, calling your attention
    如果在非 HW4 车辆上使用 1562948-70-D 版本零件,则将接地带 1679240-00-a 添加到流线型透镜总成上。
  41. 在助手的帮助下,从车上拆下仪表板分总成。
    Informational PurposesAn informational icon, calling your attention
    向后滑动仪表板分总成,将其向上抬离仪表板支架。
    Informational PurposesAn informational icon, calling your attention
    确保气流出风口和副驾位安全气囊与下部仪表板总成无接触。
    Informational PurposesAn informational icon, calling your attention
    从右前门取出仪表板分总成。
  42. 断开气流通风系统电气连接器(4 个)。
    Informational PurposesAn informational icon, calling your attention
    将仪表板分总成朝上放置于一个受保护表面上以够到电气连接器。
  43. 拆下将仪表板流线型透镜总成固定到仪表板分总成上的螺钉(5 个)。
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  44. 向前旋转仪表板分总成,松开将其连接至仪表板流线型透镜总成的锁片(8 个)。
  45. 从仪表板分总成上拆下仪表板流线型透镜。
  46. 拆下副驾位出风口总成的螺钉(4 个)。
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  47. 拆下驾驶位出风口总成的螺钉(5 个)。
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  48. 松开右侧流线型透镜盖卡子。
  49. 松开左侧流线型透镜盖卡子。

安装

  1. 安装将驾驶侧出风口总成连接至仪表板流线型透镜的螺钉(5 个)。
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  2. 安装副驾位出风口总成的螺钉(4 个)。
    2 Nm (1.5 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  3. 紧固右侧流线型透镜端盖卡子。
  4. 紧固左侧流线型透镜端盖卡子。
  5. 将仪表板流线型透镜放到仪表板分总成上。
    Informational PurposesAn informational icon, calling your attention
    将仪表板分总成锁片(8 个)与仪表板流线型透镜对齐后装入。
  6. 将仪表板流线型透镜旋入仪表板分总成,并用锁片(8 个)将其紧固。
    Informational PurposesAn informational icon, calling your attention
    向后转动仪表板分总成以锁止锁片(8 个)。
  7. 安装将仪表板流线型透镜连接至仪表板分总成的螺钉(5 个)。
    2.5 Nm (1.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  8. 连接气流通风系统电气连接器(4 个)。
  9. 在助手的帮助下,安装仪表板分总成。
    Informational PurposesAn informational icon, calling your attention
    将仪表板分总成滑入车内。
    Informational PurposesAn informational icon, calling your attention
    确保副驾位气囊和驾驶位出风口总成与下部仪表板总成之间有间隙。
    Informational PurposesAn informational icon, calling your attention
    将仪表板分总成基线(4 条)插入仪表盘插槽。
  10. 安装仪表板接地线束固定用螺栓。
    3.5 Nm (2.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    在触摸屏右侧支架后布线。
    Informational PurposesAn informational icon, calling your attention
    如果在非 HW4 车辆上使用 1562948-70-D 版本零件,则将接地带 1679240-00-a 添加到流线型透镜总成上。
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米套筒
  11. 固定将仪表板饰板线束固定到车辆的夹子,然后连接电气连接器。
  12. 连接仪表盘线束电气连接器。
  13. 将下部仪表板总成放入仪表板分总成。
  14. 安装仪表板左下方螺钉(3 个)。
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  15. 安装仪表板中下方螺钉(6 个)。
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  16. 安装仪表板右下方螺钉(3 个)。
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 梅花 T20 批头
  17. 安装仪表板支架横梁固定用螺栓(2 个)。
    3 Nm (2.2 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具:
    • 10 毫米套筒
  18. 连接副驾驶位处安全气囊电气连接器(3 个)。
  19. 安装副驾位仪表板导管。请参阅Duct - Instrument Panel - Front Passenger (Remove and Replace)
  20. 安装主仪表板装饰。请参阅Decor - Instrument Panel - Main (Remove and Replace)
  21. 安装手套箱。请参阅Glove Box (Remove and Replace)
  22. 安装副驾位膝部气囊。请参阅Knee Airbag - Front Passenger (Remove and Replace)
  23. 安装中控台 RH 侧面板地毯。请参阅Carpet - Side Panel - Center Console - LH (Remove and Replace)
  24. 安装副驾位脚部空间盖板。请参阅Cover - Footwell - Passenger (Remove and Replace)
  25. 安装右侧 A 柱下部饰板。请参阅Trim - A-Pillar - Lower - LH (Remove and Replace)
  26. 安装右前门槛饰板。请参阅Trim - Sill Panel - Front - LH (Remove and Replace)
  27. 安装副驾位脚垫。
  28. 安装右侧 A 柱上饰板。请参阅Trim - A-Pillar - Upper - LH (Remove and Replace)
  29. 安装右侧遮光板 A 柱饰板。请参阅Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace)
  30. 安装右侧 A 柱中间饰板。请参阅Trim - A-Pillar - Middle - LH (Remove and Replace)
  31. 安装右侧仪表板端盖。请参阅End Cap - Instrument Panel - LH (Remove and Replace)
  32. 安装右侧仪表板中间饰板。请参阅Trim - Middle - Instrument Panel - RH (Remove and Replace)
  33. 紧固用于固定仪表板封闭板的锁片(4 个)。
  34. 安装触摸屏。请参阅Touchscreen (HW3) (Remove and Replace)
  35. 安装仪表板维修面板。请参阅Service Panel - Instrument Panel (Remove and Replace)
  36. 安装中控台手机底座。请参阅Phone Dock - Center Console (Remove and Replace)
  37. 重新连接低压电源。请参阅LV Power (Disconnect and Connect)
  38. 安装前备箱后部挡板。请参阅 Underhood Apron - Rear (Remove and Replace)
  39. 将副驾位座椅移回原位。
  40. 向下长按上部 B 柱按钮,校准右后车门。
  41. 关闭右前车门。
  42. 安装左侧 A 柱上饰板。请参阅Trim - A-Pillar - Upper - LH (Remove and Replace)
  43. 安装左侧遮光板 A 柱饰板请参阅Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace)
  44. 安装左侧仪表板中间饰板。请参阅Trim - Middle - Instrument Panel - LH (Remove and Replace)
  45. 安装左侧仪表板端盖。请参阅End Cap - Instrument Panel - LH (Remove and Replace)
  46. 安装 A 柱左侧中间饰板。请参阅Trim - A-Pillar - Middle - LH (Remove and Replace)
  47. 将转向柱复位。
  48. 将驾驶位座椅靠背移回原位。
  49. 向下长按上部 B 柱按钮,校准左后车门。
  50. 升起左侧和右侧前车窗。
  51. 关闭左前车门。