2026-07-02

执行常规检查 (Inspection)

校正代码 00030700 FRT 1.14 注意：除非本程序中另有明确规定，否则上文所列校正代码和 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

警告

本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。

2026-06-18: Released new procedure.

Procedure

Function check LH front door (exterior)

注
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
Function check all windows from the master switch

注
Check operation with door closed, Document any abnormal operation/noises
Function check LH rear door (exterior)

注
Inspect and note functionality for the door handle operation, and full range of motion of the door, From outside look for interference with brightwork and door to body, Function test closing button on door, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH rear door (exterior)

注
Inspect and note functionality for the door handle operation, and full range of motion of the door, From outside look for interference with brightwork and door to body, Function test closing button on door, Note noises such as creaks, groans and clicks, pauses or incomplete actions
Function check RH front door (exterior)

注
Inspect and note functionality for the door handle operation and full range of motion of the door, From outside look for interference with brightwork and door to body, Note any abnormalities
Function check the exterior lights

注
Recommend assistance, Check headlamps, fog lights, license plate, tail, brake, reverse, and side repeaters
Engage drive rails and activate windshield washer and wiper operation

注
Engage drive rails and hold down on the washer button, Verify wipers and washer is operating as intended
Function check horn
Open the hood.
Remove the rear underhood apron.
Remove the RH underhood apron.
Remove the LH underhood apron.
Remove the front underhood apron.
Remove the underhood storage unit access panel.
Remove the underhood storage unit carpet.
Remove the underhood storage unit from the vehicle.
Perform inspection of under hood area

注
Perform inspection of vehicle under hood area, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Inspect brake fluid level
Inspect coolant level and top off as necessary

注
Ensure that the fluid level is at the Max line, Top off fluid as required
Fill washer fluid reservoir

注
Fill the reservoir until the fluid level is visible just below the filler neck
Raise and support the vehicle.
Raise vehicle fully and lower lift onto locks

注
Set vehicle to comfortable working height, Ensure an audible click of locks on both sides is heard before lowering, Vehicle may tilt to the side if both locks are not engaged
Remove push clips securing front aero shield

注
5x push clips
Remove bolts securing front aero shield and remove from vehicle

注
9x bolts, 10mm, 6 Nm
Release mid aero shield

注
4x push clips
Remove mid aero shield

注
16x bolts, 10mm, 6 Nm
Check tire pressures

注
4x tires, Adjust to specification if necessary
Measure and record RH front tread depth

注
Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
Measure and record RH front brake pad thickness
Inspect RH front brake rotor condition

注
Check for excessive rust or wear, Minimum spec 30mm
Measure and record RH rear tread depth

注
Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
Measure and record RH rear brake pad thickness

注
Add line to replace if under 5mm
Inspect RH rear brake rotor condition

注
Check for excessive rust or wear, Minimum spec 26mm
Measure and record LH rear tread depth

注
Record at least 3 measurements: Inner, Middle, Add line to replace if under 5/32 inch tread remaining
Measure and record LH rear brake pad thickness
Inspect LH rear brake rotor condition

注
Check for excessive rust or wear, Minimum spec 26mm
Measure and record LH front tread depth

注
Record at least 3 measurements: Inner, Middle, Outer, Add line to replace if under 5/32 inch tread remaining
Measure and record LH front brake pad thickness

注
Add line to replace if under 5mm
Inspect LH front brake rotor condition

注
Check for excessive rust or wear, Minimum spec 30mm
Perform inspection of vehicle underside components front and rear

注
Perform inspection of vehicle underside front and rear, Check for signs of abnormal damage, wear, heavy rust, wiring damage, or impact damage, Pay attention to safety related component and note any items of significance
Inspect underside of vehicle for fluid leaks
Perform inspection of steering components

注
Check steering gear joints, fasteners, and electrical connections, Verify components are not bent or damaged
Perform inspection of suspension components

注
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform inspection of front suspension components

注
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Perform inspection of rear suspension components

注
Check conditions of ball joints and bushings, etc, Inspect for any loose fasteners, Carefully apply pressure with a pry bar as needed
Inspect underside of battery for damage
Install mid aero shield

注
16x bolts, 10mm, 6 Nm, Apply Loctite 222 onto mid aero shield bolts and install fasteners securing mid aero shield to vehicle
Position mid aero shield

注
4x push clips
Apply Loctite 222 onto front aero shield bolts and secure front aero shield to vehicle

注
9x bolts, 10mm, 6 Nm
Install push clips securing front aero shield

注
5x push clips
Lower vehicle fully

注
Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
Lower and remove the vehicle from the lift.
Install the underhood storage unit.
Install the underhood storage unit carpet.
Install the underhood storage unit access panel.
Install the front underhood apron.
Install the LH underhood apron.
Install the RH underhood apron.
Install the rear underhood apron.
Close the hood.
Perform a road test using a series of ABS-active stops and ensure proper brake pedal feel and performance

注
The vehicle must stop completely within 25 feet (7.6 meters) at 20 mph (32 kph), Confirm that no excessive vibration or noise is present
Inspect vehicles alignment

注
Confirm steering wheel is straight and no vibrations or noises are felt or heard from the suspension, On a flat road, at 35 mph (56 kph), the vehicle does not pull in either direction