2023-05-29

Horn - High Tone (Remove and Replace)

校正代码 17530102 0.30 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See 平均维修工时 to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure proper PPE is worn when performing the below procedure.

拆卸

Warning IconA warning icon, calling your attention to a possibly risky situation
警告
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components. Provide corrections and feedback to ServiceDevelopment@teslamotors.com.
  1. Open the LH front door.
  2. Lower the LH front window.
  3. Remove the LH front wheel. See Wheel Assembly (Remove and Install).
  4. Release the clips (x6) and push nut that partially attach the front portion of the LH front wheel house liner to the vehicle body, and then move the liner aside for access.
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • 卡子撬具
  5. Disconnect the low tone horn locking connector.
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • Small flat head screwdriver
    Informational PurposesAn informational icon, calling your attention
    注
    Release the red locking tab.
  6. Disconnect the high tone horn locking connector.
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • Small flat head screwdriver
    Informational PurposesAn informational icon, calling your attention
    注
    Release the red locking tab.
  7. Remove the nut that attaches the horn assembly to the vehicle body, and then remove the horn assembly from the vehicle.
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • 2 英寸加长件
    • 10 毫米深套筒
    • 回旋头棘轮/回旋头扭矩扳手
  8. Remove the nut that attaches the high tone horn to the horn assembly bracket, and then remove the high tone horn from the bracket.
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • 10 毫米套筒
    • Adapter 1/4in Dr. to 1/4in Hex Bit Quick Change
    • Cordless 1/4in Hex Driver

安装

  1. Position the high tone horn on the horn assembly bracket, and then install the nut that attaches the high tone horn to the bracket.
    9 Nm (6.6 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • 10 毫米套筒
    • Adapter 1/4in Dr. to 1/4in Hex Bit Quick Change
    • Cordless 1/4in Hex Driver
    • 带角度测量的扭矩扳手
  2. Position the horn assembly on the vehicle, and then install the nut that attaches the horn assembly to the vehicle body.
    12 Nm (8.8 lbs-ft)
    Informational PurposesAn informational icon, calling your attention
    TIp
    推荐使用以下工具：
    • 2 英寸加长件
    • 10 毫米深套筒
    • 回旋头棘轮/回旋头扭矩扳手
  3. Connect the high tone horn locking connector.
    Informational PurposesAn informational icon, calling your attention
    注
    Verify the red locking tab is fully seated and engaged.
  4. Connect the low tone horn locking connector.
    Informational PurposesAn informational icon, calling your attention
    注
    Verify the red locking tab is fully seated and engaged.
  5. Install the clips (x6) and push nut that attach the front portion of the LH front wheel house liner to the vehicle body.
  6. Install the LH front wheel. See Wheel Assembly (Remove and Install).
  7. Raise the LH front window.
  8. Close the LH front door.