校正代码 140524011.2 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：执行下述程序时，请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。

1. Open the LH front door.
2. Lower both front windows.
3. Move the LH front seat backward.
4. Remove LH IP end cap
   注

   7x clips, 1x datum, Ensure clip at IP carrier is released fully before removal

   

   

   

5. Remove LH mid A-pillar trim
   注

   2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim

   

   

   

6. Remove IP LH mid panel
   注

   6x tabs

   

   

   

7. Remove LH sun visor bezel
   注

   6x clips, 5x tabs, Release clips, then slide bezel towards front of vehicle to release

   

   

   

   

8. Release LH upper A-pillar from body
   注

   2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Discard nut after removal

   

9. Remove LH upper A-pillar from vehicle
   注

   1x connector, 2x datums, 6x clips, Release clips and rotate pillar inboard to access connector, Release datums upward out of IP sub assembly

   

   

   

10. Adjust steering column fully out and fully down
    注

    Via UI > Controls > Steering , Use left steering wheel scroll wheel to adjust steering column

    

    

    

11. Open the RH front door.
12. Move the RH front seat backward.
13. Open the hood.

    

14. Power off the vehicle using the touchscreen.

    

15. Remove the rear underhood apron.

    

    

16. Disconnect the LV battery connector and First Responder Loop.

    

    

    

17. Remove RH IP end cap
    注

    3x clips

    

18. Remove RH mid A-pillar trim
    注

    2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim

    

    

    

19. Remove RH front door sill trim panel
    注

    8x clips, 3x datums

    

    

20. Remove RH lower A-pillar trim
    注

    1x bolt, T25, 5 Nm, 2x clips, 1x datum

    

    

    

21. Remove RH sun visor bezel
    注

    6x clips, 1x tab, Release clips, then slide bezel towards front of vehicle to release

    

    

    

22. Release RH upper A-pillar from body
    注

    2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Discard nut after removal

    

23. Remove RH upper A-pillar from vehicle
    注

    1x connector, 2x datums, Rotate pillar inboard to access connector, Release datums upward out of IP sub assembly

    

    

    

24. Release phone dock
    注

    4x clips, 2x datums, Pull up at bottom and swing out from under instrument panel

    

    

25. Remove phone dock
    注

    3x connectors, 1x clip, Take caution to release connector locks before pulling straight out of each socket to avoid damage

    

    

26. Release the IP service panel.

    

    

    

27. Release diagnostic and CAN harnesses from IP service panel
    注

    2x clips

    

    

28. Remove IP service panel
    注

    1x connector

    

    

29. Remove center display bracket bolts
    注

    2x bolts, 10mm, 11.5 Nm

    

    

30. Remove center display shroud
    注

    3x tabs, Slide display outwards until shroud fully clears IP and support, Release the bottom tabs and pull upward

    

    

31. Release center display coax and power connectors
    注

    2x connectors, 1x clip, Slide display rearward outwards from IP bracket and support during connector release

    

32. Remove center display
    注

    Slide rearward, Place on soft clean surface

    

33. Remove IP closeout panel
    注

    4x tabs

    

    

    

34. Remove IP RH mid Panel
    注

    14x tabs, 2 datums

    

    

35. Remove IP Decor
    注

    21x clips, 6x datums, 4x connectors, Release each IP decor connector clip from IP carrier then disconnect from IP harness

    

    

    

    

    

36. Remove RH front floor mat

    

37. Remove RH footwell cover
    注

    3x magnets, 1x connector, 4x datums

    

    

38. Remove RH console side carpet
    注

    11x clips, 2x datums

    

    

39. Remove fasteners securing RH knee air bag assembly to vehicle
    注

    2x bolts, 10mm, 8 Nm, 1x clip

    

40. Remove the RH knee air bag assembly from vehicle
    注

    2x connectors, 1x clip, 6x tabs, Release 2x locking tab on air bag connector

    

    

41. Release glove box
    注

    5x screws, T20, 3 Nm

    

    

42. Release glove box connectors
    注

    3x connectors

    

43. Remove USB outlet
    注

    2x screws, T20, 3 Nm, 1x clip

    

44. Remove glove box

    

45. Release passenger IP air duct temperature sensor connector
    注

    1x connector

    

46. Remove passenger IP air duct
    注

    2x push-pull rivets

    

    

47. Remove IP carrier cross beam screws
    注

    2x bolts, 10mm, 3 Nm

    

    

48. Release passenger IP airbag connectors
    注

    3x connectors, Pull down spring loaded locks simultaneously to release airbag connectors

    

    

49. Release RH lower instrument panel
    注

    3x screws, T20, 3 Nm

    

50. Release center lower instrument panel
    注

    6x screws, T20, 3 Nm

    

51. Release LH lower instrument panel
    注

    3x screws, T20, 3 Nm

    

52. Release instrument cluster harness
    注

    1x connector, 1x clip

    

    

53. Release IP trim harness
    注

    1x connector, 1x clip

    

    

54. Position lower instrument panel assembly away from IP sub-assembly
    注

    6x datums, Move top edge as far rearward as possible without excessive stress on assembly

    

55. Release IP ground harness
    注

    1x clip, 1x bolt, 10mm, 9 Nm, Note routing behind center display RH bracket. If using part revision 1562948-70-D on a Non-AP4 vehicle, add ground strap 1679240-00-A to aero lens assembly

    

56. Remove IP sub-assembly
    注

    Slide IP sub-assembly rearward, Lift assembly up from IP carrier, Ensure airwave vents and passenger air bag are clear of lower IP assembly, Remove assembly out through RH front door, Recommend assistance as needed

    

    

    

57. Install IP sub-assembly
    注

    4x datums, Slide IP sub-assembly into vehicle, Ensure passenger air bag and driver vent assembly have clearance past lower IP assembly, Engage IP sub-assembly datums into dash slots, Recommend assistance

    

    

    

58. Secure IP ground harness
    注

    1x clip, 1x bolt, 10mm, 3.5 Nm, Note routing behind center display RH bracket. If using part revision 1562948-70-D on a Non-AP4 vehicle, add ground strap 1679240-00-A to aero lens assembly

    

    

59. Secure IP trim harness
    注

    1x connector, 1x clip

    

    

60. Secure instrument cluster harness
    注

    1x connector

    

61. Position lower instrument panel assembly into IP sub-assembly

    

62. Secure LH lower instrument panel
    注

    3x screws, T20, 3 Nm

    

63. Secure center lower instrument panel
    注

    6x screws, T20, 3 Nm

    

64. Secure RH lower instrument panel
    注

    3x screws, T20, 3 Nm

    

65. Install IP carrier cross beam bolts
    注

    2x bolts, 10mm, 3 Nm

    

    

66. Secure passenger IP airbag connectors
    注

    3x connectors

    

67. Install passenger IP air duct
    注

    2x push-pull rivets

    

    

    

68. Secure passenger IP air duct temperature sensor connector
    注

    1x connector

    

69. Install IP Decor
    注

    21x clips, 6x datums, 4x connectors, Connect ambient bright harness, Secure each IP decor connector clip to IP carrier, Secure IP decor to lower instrument panel

    

    

    

    

    

70. Secure USB outlet
    注

    2x screws, T20, 2 Nm, 1x clip, Ensure USB socket flush in glove box

    

    

    

71. Secure glove box connectors
    注

    3x connectors, Route harness through glove box datums

    

72. Install glove box
    注

    5x screws, T20, 3 Nm

    

    

73. Install RH knee air bag assembly onto vehicle
    注

    2x connectors, 6x tabs, 1x clip, Hook tabs before fully seating, Use caution not to damage the connector/harness, Support the knee air bag while connecting the connector

    

    

    

74. Install fasteners securing RH knee air bag assembly to vehicle
    注

    2x bolts, 10mm, 8 Nm, 1x clip

    

75. Install RH console side carpet
    注

    11x clips, 2x datums

    

    

76. Install RH footwell cover
    注

    3x magnets, 4x datums, 1x connector

    

    

77. Install RH lower A-pillar trim
    注

    1x bolt, T25, 5 Nm, 2x clips, 1x datum

    

    

78. Install RH front door sill trim panel
    注

    8x clips, 3x datums

    

    

79. Install RH front floor mat

    

80. Position RH upper A-pillar to vehicle
    注

    1x connector, 2x datums, Secure RH upper A-pillar harness, Align datums into IP sub assembly, Rotate upper A-pillar panel into position

    

    

    

81. Secure RH upper A-pillar to body
    注

    2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Install new nut

    

82. Install RH sun visor bezel
    注

    6x clips, 1x tab, Insert tab and slide bezel towards rear of vehicle, then secure clips

    

    

83. Install RH mid A-pillar trim
    注

    2x clips, 3x datums, Verify weather seal is seated properly

    

    

    

84. Install RH IP end cap
    注

    3x clips

    

85. Install IP RH mid Panel
    注

    14x tabs, 2 datums

    

    

    

86. Install IP closeout panel
    注

    4x tabs

    

    

    

87. Route display harness behind LH display bracket

    

88. Secure center display coax and power connectors
    注

    2x connectors, 1x clip, Ensure strain relief clip is secure to linkage arm, Replace clip if damaged

    

89. Install center display shroud
    注

    3x tabs, Slide display downward until shroud tabs fully engages

    

    

90. Secure center display to IP carrier
    注

    2x bolts, 10mm, 11.5 Nm, Slide center display into IP carrier, Start RH bolt first

    

    

    

91. Secure IP service panel connector
    注

    1x connector

    

    

92. Secure diagnostic and CAN harnesses to IP service panel
    注

    2x clips

    

    

    

93. Install the IP service panel.

    

    

94. Install phone dock connections
    注

    3x connectors, 1x clip

    

    

95. Install phone dock
    注

    2x datums, 4 tabs, Slide datums forward into IP and secure tabs down into center console

    

    

96. Connect the First Responder Loop and LV battery connector.

    

    

97. Install the rear underhood apron.

    

    

98. Close the hood.
99. Move the RH front seat to its original position.
100. Calibrate the RH falcon wing door.

     

101. Close the RH front door.
102. Position LH upper A-pillar to vehicle
     注

     1x connector, 2x datums, 6x clips, Secure LH upper A-pillar harness, Align datums into IP sub assembly, Rotate upper A-pillar panel into position engaging clips fully

     

     

     

103. Secure LH upper A-pillar to body
     注

     2x bolts, 10mm, 5 Nm, 1x screw, T20, 2.5 Nm, 1x nyloc nut, 13mm, 5 Nm, Install new nut

     

104. Install LH sun visor bezel
     注

     6x clips, 5x tabs, Insert tabs and slide bezel towards rear of vehicle, then secure clips

     

     

105. Install IP LH mid panel
     注

     6x tabs

     

     

     

106. Install LH mid A-pillar trim
     注

     2x clips, 3x datums, Insert mid A-pillar trim into lower A-pillar trim, Secure clips into upper A-pillar and IP sub assembly, Verify weather seal is seated properly

     

     

     

107. Install LH IP end cap
     注

     7x clips, 1x datum

     

     

108. Adjust steering column back to original position
     注

     Via UI>Controls>Steering , Use left steering wheel scroll wheel to adjust steering column

     

     

     

109. Move the LH front seat to its original position.
110. Calibrate the LH falcon wing door.

     

111. Raise both front windows.
112. Close the LH front door.