25/06/2024 08:37:43

前照灯 - 调节(全球)(工具法)

校正代码 17400170 0.18 注意:除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。 注意:请参阅平均维修工时,深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈,请发送电子邮件至LaborTimeFeedback@tesla.com 注意:执行下述程序时,请参阅人员保护确认已穿戴适当的个人防护装备 (PPE)。 注意:除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。 注意:请参阅平均维修工时,深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈,请发送电子邮件至LaborTimeFeedback@tesla.com 注意:请参阅人员保护,确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。

  • 2024-06-13: Updated procedure to latest validation.

Adjustment

  1. 启用前照灯调节模式:
    1. 在车辆触摸屏上,点击Controls > Service > Adjust Headlights
    2. 如果系统提示您校准前照灯(图 A),请继续子步骤 c。如果系统提示您调节前照灯(图 B),请转至步骤 2。
      图 1. 图 A
      图 2. 图 B
    3. 按照触摸屏上的提示操作以校准前照灯。所有 4 项检查均由“红”变“绿”后,校准完成。
      Informational PurposesAn informational icon, calling your attention
      校准驾驶车程最长可达 2 公里(1.24 英里)。
      Informational PurposesAn informational icon, calling your attention
      为确保校准准确无误:
      • 启用驱动导轨后至少等待 1 秒,然后再换入Drive
      • 关闭所有车门,执行校准驾驶期间请勿打开车门。
      • 停车后至少等待 1 秒,然后再打开车门。
      • 车辆倒车距离不得超过 10 米。如果因车库条件而无法避免此情况,请在车辆离开车库后再开始前照灯校准。
    4. 前照灯校准完成后,可以对前照灯进行调节。继续执行下一步骤。
  2. Set vehicle ride height to "Low".
    Informational PurposesAn informational icon, calling your attention
    Using the touchscreen, touch Controls > Suspension > Low.
  3. Activate Jack Mode.
    Informational PurposesAn informational icon, calling your attention
    Using the touchscreen, touch Controls > Service > Jack Mode.
  4. Open the hood.
  5. Switch on the headlights.
  6. If not yet entered, enter the headlight adjustment mode through the touchscreen.
    Informational PurposesAn informational icon, calling your attention
    Using the touchscreen, touch Controls > Service > Adjust Headlights.
  7. Position headlight aimer in front of the LH headlight.
    Informational PurposesAn informational icon, calling your attention
    Position the headlight aimer at 30 cm (~ 12 in) distance from the surface of headlight lens. Adjust the height as necessary to match the center point of the headlight (81 cm/32 in).
  8. Power on the headlight aimer.
  9. Use the knobs on the base to adjust tester level.
  10. Use the visor/laser to line up the tester perpendicular to the axis between the hood struts.
    Informational PurposesAn informational icon, calling your attention
    If the headlight aimer can move between RH and LH headlights while maintaining the same laser angle projected onto the hood struts, it is set correctly - perpendicular to the car
  11. Regardless of the region, select TEST EC on the headlight aiming tool.
  12. Select Free test.
  13. Select Vehicle, and then use the + or - buttons to set the vehicle type to Tesla X.
  14. Select Headlight, use the + or - buttons to set the Headlight type to EU Asym, and then use the small - button next to the EU Asym field to select TMR.
  15. Select Light, and then use the + or - buttons to set the Light type to Bi-LED.
  16. Select Inclinat., and then use the + or - buttons to set the inclination to 0.0 %.
  17. Select Height, and then adjust to 81 cm using the +/- buttons.
  18. Press OK, and then press OK again to skip the fog light settings.
  19. Select the laser icon and adjust the tester horizontal and vertical position to align with the LH headlight markings.
  20. Turn off the laser guide.
  21. On the headlight tester tool, press the LH TMR button on the left side of the screen, and then press the TMR button at the bottom of the screen.
    Informational PurposesAn informational icon, calling your attention
    The "L" and "R" indicators at the bottom of the screen are reversed: "L" is on the right side and "R" is on the left side.
  22. On the vehicle touchscreen, touch Left.
  23. On the steering wheel, use the left scroll wheel to adjust the beam. When adjusted to within specification, the color of the beam indicator on the headlight tester tool will change from red to green.
    Informational PurposesAn informational icon, calling your attention
    There might be a delay between the scroll wheel input and the actual headlight adjustment output.
    图 3. Model Y shown, Model X similar
  24. Select the save icon to record results
  25. On the headlight tester tool, press the "Save" button to record the results for the LH headlight.
  26. Move the headlight tester tool to the RH headlight, position the tool ~ 30 cm (~ 12 in) from the front of the RH headlight lens.
  27. Align the tool to the RH headlight (see steps 19 and 20).
  28. On the headlight tester tool, press the RH TMR button on the right side of the screen, and then press the TMR button at the bottom of the screen.
    Informational PurposesAn informational icon, calling your attention
    The "L" and "R" indicators at the bottom of the screen are reversed: "L" is on the right side and "R" is on the left side.
  29. On the vehicle touchscreen, touch Right.
  30. On the steering wheel, use the left scroll wheel to adjust the beam level. When adjusted to within specification, the color of the beam indicator on the headlight tester tool will change from red to green.
    Informational PurposesAn informational icon, calling your attention
    There might be a delay between the scroll wheel input and actual headlight adjustment output.
    图 4. Model Y shown, Model X similar
  31. On the headlight tester tool, press the "Save" button to record the results for the RH headlight, and then press "Save" again to view the results for both headlights.
  32. Press the "Print" button to print out the results, if desired.
  33. Close the front trunk.
  34. On the touchscreen, exit the headlight adjustment mode.