校正代码 11334712 1.56 NOTE: Unless otherwise explicitly stated in the procedure, the above correction code and FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See 平均维修工时 to learn more about FRTs and how they are created. To provide feedback on FRT values, email ServiceManualFeedback@tesla.com. NOTE: See 人员保护 to make sure proper PPE is worn when performing the below procedure.

1. Open the LH front door.
2. Lower the LH front window.
3. Lower LH rear window
4. Open LH falcon wing door
5. Remove LH falcon door lower garnish
   注

   9x V-clips, Replace any damaged or missing clips, Take care not to damage door trim panel during removal

   

   

6. Remove LH rear decor trim panel
   注

   7x clips, 2x connectors

   

   

   

7. Remove bolts securing LH rear door panel to door
   注

   8x bolts, 10mm, 6 Nm

   

8. Raise LH rear window

   

9. Disconnect ultrasonic ECU
   注

   1x connector, Release black locking tab

   

10. Remove LH rear door trim panel
    注

    13x clips, 2x connectors

    

    

11. Open the hood.

    

12. Power off the vehicle using the touchscreen.

    

13. Remove the rear underhood apron.

    

    

14. Disconnect the LV battery connector and First Responder Loop.

    

    

    

15. Disconnect 2nd row head air bag connector
    注

    1x connector, Release orange lock and then disconnect

    

16. Remove bolts securing LH closeout panel to falcon door
    注

    10x bolts, T25, 8mm, 1.8 Nm

    

    

17. Release window motor from LH closeout panel
    注

    3x screws, T30, 1.8 Nm

    

18. Disconnect LH rear door controller
    注

    2x connectors

    

19. Release clips securing lower falcon door harnesses and connectors to LH closeout panel
    注

    7x clips

    

20. Release emergence release cable
    注

    Unclip and feed door release cable through LH closeout panel

    

21. Release LH rear closeout panel
    注

    2x tabs, Pull LH closeout panel away from door and lift window motor up to release

    

    

22. Remove LH rear closeout panel
    注

    1x clip

    

23. Remove spacer, spring, and cap from LH ultrasonic sensor

    

    

24. Disconnect LH ultrasonic sensor
    注

    1x connector, 1x clip

    

    

25. Remove LH ultrasonic sensor

    

26. Remove LH sensor carrier
    注

    Use heat gun to apply heat up to about 55 Celsius or 131 Fahrenheit and distance around 18 cm diameter of sensor carrier assembly to cover the 3 mounting areas, Used one hand to feel the areas behind the door skin to assure the heating areas locations

    

    

    

27. Remove LH Butyl Ultrasonic Holder
    注

    Use only plastic pry tools to assist pulling the butyl patch, pull as vertical as possible

    

28. Clean LH Butyl Ultrasonic Holder leftovers
    注

    Use only plastic tools, heating the butyl for a few seconds helps the use of IPA wipes, make sure the surface is completely clean and dry

    

    

29. Prepare Butyl Ultrasonic Holder
    注

    Place the patch with the wrap on the door and note the correct orientation, remove the wrap without touching the butyl area, clean the door installation location with IPA wipes one more time

    

    

30. Install LH Butyl Ultrasonic Holder
    注

    Place it as flat as possible on the door, make sure the sensor holder holes are properly aligned

    

31. Flatten LH Butyl Ultrasonic Holder
    注

    Use pressure roller from the center outwards to press the butyl patch and remove bubble gaps and creases

    

    

32. Clean LH ultrasonic mounting area
    注

    Use IPA wipes or isopropyl alcohol to clean the area, allow 1 minute to dry

    

33. Apply adhesion promoter to LH ultrasonic mounting area
    注

    Allow 1 minute to dry

    

34. Heat up LH Falcon door panel
    注

    Use heat gun and heat up the door skin. If necessary, use the infrared thermometer to check the temperature of door panel to at least 25 degrees C (77 degrees F) evenly

    

35. Install LH sensor carrier
    注

    Peel off stickers prior install, install with harness slot in lower position, use the force gauge to apply a force of 70 N to the top of each of the carrier pads for at least 10 seconds.

    

    

36. Prepare LH Ultrasonic sensor for installation
    注

    Use heat gun and IR temp gun to read temperature of door panel to install Ultrasonic sensor, heat up LH Falcon door panel to 25º C and sensor to 40º -50º C, use heat gun and IR temp gun as needed

    

    

37. Install LH ultrasonic sensor

    

    

38. Use force gauge to press sensor into door and secure
    注

    Attach the 22 mm tip to the force gauge, Press @ 50N for 10 seconds

    

39. Install spacer, spring, and cap to secure LH ultrasonic sensor

    

    

40. Connect LH ultrasonic sensor
    注

    1x connector, 1x clip, Engage red locking tab after securing connect

    

    

41. Secure window regulator harness
    注

    1x clip

    

42. Install release cable through LH closeout panel

    

43. Position LH window motor onto back of closeout panel
    注

    2x tabs

    

    

44. Install window motor to closeout panel
    注

    3x screws, T30, 1.8 Nm

    

45. Install LH closeout panel
    注

    10x bolts, T25, 8mm, 1.8 Nm

    

    

46. Connect ultrasonic ECU
    注

    1x connector, securing locking tab

    

47. Connect LH 2nd row head air bag connector
    注

    1x connector, Engage locking tab

    

48. Connect LH rear door controller
    注

    2x connectors

    

49. Install clips securing harnesses and connectors to LH closeout panel
    注

    7x clips

    

50. Install LH rear door trim panel
    注

    2x connectors, 13x clips, Install door trim starting from top and make sure the door trim tab is fitted correctly on the inner belt seal

    

    

51. Install bolts securing LH rear door panel to door
    注

    8x bolts, 10mm, 6 Nm

    

52. Install LH rear door decor trim panel
    注

    7x clips, 2x connectors, Take care not to damage door trim panel

    

    

    

53. Install LH rear lower door garnish
    注

    9x V-clips

    

    

54. Connect the First Responder Loop and LV battery connector.

    

    

55. Install the rear underhood apron.

    

    

56. Close the hood.
57. Calibrate LH and RH Falcon Wing doors from center display
    注

    Calibration required after LV system is powered down > Service > Calibrate Doors > Hold down Calibrate doors until doors cycle > Calibration Complete Message will appear

    

    

    

    

58. Raise the LH front window.
59. Close the LH front door.